This is the smps circuit, the 220 V to 12VDC AC circuit, with a maximum current 60A. This circuit is still being tested, you can do it, but be careful with 220v voltage. I will redesign this smps circuit, with full protection and voltage feedback. Soon, wait for me. Download file PWM here: update... Facebook group : bit.ly/CreativeElectronic #SMPS #12Vto220V #Inverter
friend compliments for your work and your efforts you were simply born for electronics and you seem to love what you do I wish you good luck greetings from serbia
Good video, but are you willing to share the schematic anytime soon?, i'd like to ask more questions if it doesnt bother you, it will be extremely helpful if you replay because ive been trying to make one for quite sometime.
The circuit is cool , easily ONLY put this vídeo in low speed same 0.5 , the voltage folow the number of turns on secundary . Thanks and wating for the protection .. bye bye
Sir, I've designed a 24V half-bridge SMPS with an IR2153 IC. I'm getting a 24V output, but when I connect a load, the voltage drops to below half of 24V. What is the problem, and how can I fix it?
No. the o/p of the ic is not sufficient to drive 10 mosfets. You need to use some gate drivers. Or you can synchronize more sg3525 to get more power(like paralleling smps)
test chơi thôi, chứ nguồn này ít ai chơi đẩy kéo lắm. dùng nửa cầu sẽ an toàn hơn (fet chỉ cần điện áp thấp ) , biến áp đơn giản hơn ( 1 cuộn ). mình chưa có thời gian thiết kế lại , vài hôm nữa có time ngồi thiết kế bộ nguồn 100A 12V hoặc 24V chuyên dùng test inverter thay ắc quy cho ngon.
Sir I have a UPS transformar I want to convert or rewind that transformer to 20 0 20volt 5amp . Pls tell . Primary coil SWG.? Primary Coil turn.? Secondary Coil SWG? Secondary Coil turn.? Bobin Size of my transformer is 4.3cmx 5cm
Primary voltage= 220v Primary turns= 461turns Primary wire size= 0.538mm diameter( check for the SWG no using SWG gauge table) Secondary voltage= 20V with center tap(20v 0 20v) Secondary turns= 44 turns using bifilar winding technique( that's winding two closely spaced parallel winding) Google about it to understand Secondary wire size= 1.785mm diameter The above calculation is based on 1) 50Hz frequency 2) 1Tesla of Magnetic induction or flux density 3) 4A/mm²(or 500cmil/A) Current density. Note: increasing the flux density lowers the number of turns but gives rise to higher temperature rise
WIRE GAZE, TRANCE , ???? BOHUT KUCH AAP NE DIKHAYA AUR BOLA NAHI. 2ND CAPACITOR KA VALUE , RESISTANCE VALUE , 1ST TRANSFORMER KA VOLTAGE, PRIMARY & SECONDARY ???? KUCH NAHI DIKHAYA. AUR BOLA GAYA. VIDEO KARNE KE TIME PE PLEASE YE SAB DHAYAN DIJIYE.
This is the smps circuit, the 220 V to 12VDC AC circuit, with a maximum current 60A. This circuit is still being tested, you can do it, but be careful with 220v voltage. I will redesign this smps circuit, with full protection and voltage feedback. Soon, wait for me.
Download file PWM here: update...
Facebook group : bit.ly/CreativeElectronic
#SMPS
#12Vto220V
#Inverter
Weating for complete design?
please make acomplete design video i am still waiting for it
interesting for wait
you put 3 bulbs =210 watts
but 12×60=720 so u need 10 bulbs for 60 apm.
Still waiting for complete circuit diagram and detail thanks
friend compliments for your work and your efforts
you were simply born for electronics and you seem to love what you do
I wish you good luck
greetings from serbia
❤❤Awesome just remembered me to do something thanks😊
Good video, but are you willing to share the schematic anytime soon?, i'd like to ask more questions if it doesnt bother you, it will be extremely helpful if you replay because ive been trying to make one for quite sometime.
But the out put rectifier inductor is too small for 60amps
The circuit is cool , easily ONLY put this vídeo in low speed same 0.5 , the voltage folow the number of turns on secundary . Thanks and wating for the protection .. bye bye
Its not 60A SMPS,
can we get reup without FB,? i dont use that and i hate it..
Plz give us direct link of daigram
The link which is given there is no daigram it my 3rd comment
No schematic diagram
NO parts number
It's garbage😡
We are waiting for this project...
Bạn giỏi quá. That's very good
thanks bro
there are 4 components that I don't know would you mind to tell me that 4 components? 2 resistor, 1 coil and 1 caps
What is the value of resistor and should I add a fr107 diode too?
Паял полевики IRFP460, а по концовки полевики совсем другие стоят.Они даже не в корпусе ТО 247.Не надо бабушку обманывать...
How to understand nothing shown
Please share schematic
I like your video's
Can you make 220vac to 30vdc @ 10amp constant current general purpose bench power supply circuit? Please. . .
ok, wait me
7:15 he try steal the show
Schematic Sir
Awesome video
thanks bro
Good job
Sir, I've designed a 24V half-bridge SMPS with an IR2153 IC. I'm getting a 24V output, but when I connect a load, the voltage drops to below half of 24V. What is the problem, and how can I fix it?
Measure the voltage and current on the bulbs.
ITs amazing dear..
what type smps primer 100+100 turn....normal HB smps only 20 to 40 turn winding...
but nice design
i cannot find the schematics in facebook
Please make a simple smps welding machine
Good idea, I will do it.
@@PhdHungplease. I am waiting
@@PhdHung when you do it. please inform me
Sir can i use smps transformer for these circuit
IRF460 and you can put IRFZ44
no. irfz44 vdss 0nly 55v
Dear bro you have told all the secrets except schematic......please share it also...
This is a test version, I will soon make a better version, wait for me.
Pls try to make a 120V to 12v 60A.
Circuit diagram
ok, wait me update
IRF250n mosfet can use
Sir me i asked you..?
What if 43n60 replace to 50n60
The other part of power supply can damage?
It still works fine
Hello, please can get in contact with you?
I have some questions and will need your help to guide me.
210W÷12V=17.5A tell me where is 60A😊
Very good tnx
Push pull isn't suitable for this voltages and it need MOSFETs with atlest 3 times of input voltage ,
yes, Half-bridge is the better option
can you share this circuit please
Sir Move to place of sg3525 and any other drive in place of driver drive such as tl494 drives will work. Any drive
Haha sir.
With this schematic, can i get 100a? .. With 10x mosfet?..
No. the o/p of the ic is not sufficient to drive 10 mosfets. You need to use some gate drivers. Or you can synchronize more sg3525 to get more power(like paralleling smps)
I have seen many projects which claimed 4 volt 2amp battery gives 12 volt 10 amps, thats totally false
Can you show me the URL that is false ??
Nice video bro plz make Mppt solar charge controller pcb video
bạn ơi ko có mạch dập dòng rò dc đặt vào 2 chân của mạch chỗ sơ cấp hả bạn
test chơi thôi, chứ nguồn này ít ai chơi đẩy kéo lắm. dùng nửa cầu sẽ an toàn hơn (fet chỉ cần điện áp thấp ) , biến áp đơn giản hơn ( 1 cuộn ). mình chưa có thời gian thiết kế lại , vài hôm nữa có time ngồi thiết kế bộ nguồn 100A 12V hoặc 24V chuyên dùng test inverter thay ắc quy cho ngon.
Hoặc dùng cầu h
What if I use Voltage doubler? The Input is 110 volts to doubled as 220 Vac. The power is the same?
If the doubler can handle 800W then it should work, but still do your research because im not 100% sure
OK thanks sir I am waiting for your help me
12v 200AH 2000w power supply ki need h sir kaise bnaye
Please complete ASAP
I have build pwm by using scheme from home 102. And it running an inverter well. Where was the gdt in this project? Please share the gdt part, thanks
IRFP460 500V NO NO NO 2SK2749 900V YES
Não gosto de vídeos mudos
12v 60amp????
3 lamp ~±100 w...60a?..no
Thanks.
Whether the torodil transformer can be used in it
Please share the frequency for this project. Please redesign this project.
I made this project but both MOSFETS are burn
Thanks bro
did you choose the inductor and capacitor value randomly or you calculate ?
plz reply me
This is not for conputers and servers you could just use common values
Where is the circuit ?
Is there any possible to recharging battery
Sir I have a UPS transformar I want to convert or rewind that transformer to 20 0 20volt 5amp .
Pls tell .
Primary coil SWG.?
Primary Coil turn.?
Secondary Coil SWG?
Secondary Coil turn.?
Bobin Size of my transformer is
4.3cmx 5cm
Primary voltage= 220v
Primary turns= 461turns
Primary wire size= 0.538mm diameter( check for the SWG no using SWG gauge table)
Secondary voltage= 20V with center tap(20v 0 20v)
Secondary turns= 44 turns using bifilar winding technique( that's winding two closely spaced parallel winding) Google about it to understand
Secondary wire size= 1.785mm diameter
The above calculation is based on
1) 50Hz frequency
2) 1Tesla of Magnetic induction or flux density
3) 4A/mm²(or 500cmil/A) Current density.
Note: increasing the flux density lowers the number of turns but gives rise to higher temperature rise
@@okpalamichael4162 Do we need to remove existing primary winding also? Can't we just rewind new secondary.
Can I drive half bridge using this module and gate drive transformer?
Yes, it will work fine, using frequencies greater than 15Khz.
WIRE GAZE, TRANCE , ???? BOHUT KUCH AAP NE DIKHAYA AUR BOLA NAHI. 2ND CAPACITOR KA VALUE , RESISTANCE VALUE , 1ST TRANSFORMER KA VOLTAGE, PRIMARY & SECONDARY ???? KUCH NAHI DIKHAYA. AUR BOLA GAYA. VIDEO KARNE KE TIME PE PLEASE YE SAB DHAYAN DIJIYE.
I have 12volt 5 amp battery charger output12 voltage ok but amp not showing whats the problem please solve it and make a video on it
Sir please l request to have a 12vdc to AC 220v/60ampier circuit board made it now for power supplies inverter circuit board
yes, wait me
This trafo with gap?
Bhai ap kis contry se ho
Can I link a video of the method of making a oscillator in the video 😘
Are you using 1200V IGBT?
Mình đang có ý tưởng dùng mạch SG3525 để cấp xung cho MOSFET và nguồn nuôi cho SG3525 được hạ áp bằng tụ
Nên dùng con IR2153 ấy b
Please edit the video or make a statement @homemade 102
Resistor across gate and source is 10K ?
Iron tranformee for what.....??
Please make using this to charging battery
Boa noite amigo tem como você disponibilizar o o diagrama elétrico da fonte de 60 amperes
plese give circuit daygram how u connect all the components
Tda7294ic DC to DC no working
Mạch này vẫn hồi tiếp được phải không ạ anh?
Agar bole saktey ho tou bol k btao.agar goongey behrey ho tou ap ye kam na kro
awesome....
sir can you make the same circuit with the two mosfets in half bridge mode
YES you can
12V 60A from 220VDC work?
ok. work
Excelente
Bhai is videos Mai kuch samaj Mai nahi Aya feedback kese Kam Kare ga
Sir use any sg3525 drive board
Yes, if I had time, I would do it
60A really ?????
Amigo passa o esquema por favor
I'm want to buy board 12v 60a
Nice make full circuit with protection can u design for 100v 0v 100v 20amp for amplifier
yes, wait me
Please file updates
DIAGRAMA POR FAVOR
Sir I request to you that a kit are indactiv I load work as a transformer.other moter work on this device
Hello
design?????
I will redesign.
Please give me circuit diagram
what is the wire used in transformer enameled copper or bar wire(insulated or non insulated)
Non insulated of course
2x 900v mosfet
sir plese tel me if i want 12-0-12 so wt i do
Sir please upload components list and circuit pdf
request schema...
60A paku 5mm aja merah itu cuma ujung kabel.
plz sir help me my 30 v dc 30 amp varaible Power supply make vedios plz
Sir i need this module please help me