Introducing the NTB7L BreakFree® Power Tube Bender

The NEW BreakFree® Power Tube Bender allows you to bend a tube to customized angles by pressing a single controller switch.
For those of you who did not get a chance to see an in-person demo, Be sure to watch this 10-min video which shows you in-depth what’s included in the kit, how to use it, and how to master the tube bending tasks.
.
.
#NTB7L #PowerTubeBender #NAVAC #NAVACtools #worksmarter #hvactools #hvac #hvaclife #airconditioning #hvactechnician #hvacservice #hvactech #heating #hvacr #hvacinstall #hvacrepair #cooling #ac #heatingandcooling #hvactools #airconditioner #refrigeration #hvaclove #hvaccontractor #contractor #hvacquality #maintenance #hvacmaintenance #acrepair #hvachacks #hvacinstall

[@chrispan8037]

Looking good ！

[@NAVAC]

Thank you! Cheers!

[@HVACShopTalk]

Good job AK

[@AKHVAC]

Thanks man, trying to knock some rust off!

[@own0805]

wow good to see you again ak. hopefully you can upload videos again on your personal channel @

[@justwork_hvac]

Awesome 🤟💯🌎

[@keenanwalker6597]

Might have to grab this add it to my navac swaging kit. Only thing I wish was it did past 90. I 180 power bender would be game changer or one that dude hard pipe like the rems

[@NAVAC]

Thanks for the suggestion!

[@20antman]

Hey I see this tool makes a nice 90 degree. But can I put a mark on my cooler then know where my bend will be? Or I just have to bend then cut my copper to fit in place?

[@nmhvactech5474]

This is my biggest question. Where are the marks to get a precise length dimension bend? I like to bend almost everything to my measurements, no extra braze joints!!

[@techbass9440]

Should work like any other bender. Line up you bend offset from the center of the mandrel you should be golden.

[@drewpally]

Will it bend 3/8 stainless .365?

[@ELDIESTRODIY]

And everyone ask about other material and radio silence we guess just soft Cooper

[@NAVAC]

HI, our NTB7L Power Tube Bender is recommended for use only on soft copper. Thank you.

[@MiguelRR1975]

Is this work for emt conduit?

[@Jamie.W]

What's the comparison on the radius to a ratcheting. Same or little tighter.

[@Jamie.W]

@AKHVAC it looks to be a little tighter then the cps I have.

[@daveg8918]

Hey Andrew question is this unit for sale yet??

[@AKHVAC]

You can pre order it from TruTech Tools today to lock yours in, all NAVAC distributors should begin receiving theirs in late March/early April 👍

[@daveg8918]

@@AKHVAC thank you very much!! I did order it today from tru tech

[@123mrchilango]

It doesn’t work for reverse bend
I try it couple times and mess up my copper or I get a defective piece?

[@NAVAC]

Please contact [e-mail].

[@yzzuwnitsuj7551]

Ok well i build and plumb auto car wash equipment. I work with 1/2" and 3/4" stainless steel tubing, you say this is just for soft copper? I bend ALOT of stainless tubing by hand, not a ratcheting crossbow but just a hamd bender, if this could bend my stainless id buy immediately

[@emypena]

This thing is already $488 and still without the revese bending accessory is too expensive

[@neiadvv]

This machine do pipe ripe L?

[@AKHVAC]

ACR soft copper only

[@cn81821]

此產品哪個國家製造？

[@nando5302]

Giveaway???…

[@NAVAC]

Not a bad idea….we will chew on that once they come in!

[@FernandoGarcia-lv3mj]

😍😍😍😍😍