I have the same problem mate with bamboo leaf🍃 doesn't matter which way the wind is blowing they wind up in the pond! Cracking set up and cheers for doing the vids👍
Rectangular ponds have 4 dead spots and kills a good flow of circulation A good design with a good skimmer, and half those leaves would never make it to where they start to sink.
Koi select , quality setup but those 🍂 would do my Nut in , so personally would put a fine mesh over pond in 🍂y season stop all that and stop any potential leaching from leafs that could possibly cause issue’s. But what a pond 👍🏻
Hi. Your pond looks awesome. The filters are massive - impressive moving bed. Can not over filter. My 2 tougths. If you extend the inlet to the pumps with an extended mesh like the oase drum combi might help with the blocking. Also Like to see the video how you going to clean the settling tank.
Wow great set up! Forgive for asking but is your pond made of Reinforced Concrete? And then do you just paint it with a suitable waterproof paint. Here in the UK everybody is obsessed with fibre glass and EPDM liners. I think particularly fibre glass is not environmentally friendly. Would be very interested to know. Your fish look amazingly healthy and water clear to the bottom. Fab!
from what i could see, your skimmers are not working correctly. The idea of a skimmer is to pull the water surface tension which drags everything on the surface into the skimmer.... but with yours, the surface water does not appear to pull the water surface tension.
@@koiselectsa it looks as if your skimmer is too low and therefor is not working. the water is free flowing over the submerged skimmer door (flap weir) and most of the volume of water that enters the skimmer is not surface water... its in the name, the surface water should be what is being skimmed from the pond... as for your other skimmer, it appears to be at the correct height but i did not see the surface water being pulled into the that skimmer either. Maybe there is not enough water being pumped out of the skimmer boxes, but as you mentioned that you are pumping a lot of water, i can only assume the skimmer door is missing, or stuck fully open, and the other one is definately submerged and maybe something else as well. it is easy to investigate and figure it out. look in the top access door/clean out and check the flap weir. only surface water should be flowing over it... the inside of your skimmer should have a lower surface height than the pond and the pond water should be flowing into the skimmer box like a tiny waterfall over the skimmer door (flap weir).
A few leaves for 2 months of the year is a small sacrifice for a cracking pond. Great set up and filtration 👍
Amazing filter system lovely pond and fish stay safe
I have the same problem mate with bamboo leaf🍃 doesn't matter which way the wind is blowing they wind up in the pond! Cracking set up and cheers for doing the vids👍
Nice one Q. Your system set up perfect an neat! Well done 👌
Love your pond mate please update more video love it
Very nice setup 👌
Rectangular ponds have 4 dead spots and kills a good flow of circulation A good design with a good skimmer, and half those leaves would never make it to where they start to sink.
Koi select , quality setup but those 🍂 would do my Nut in , so personally would put a fine mesh over pond in 🍂y season stop all that and stop any potential leaching from leafs that could possibly cause issue’s. But what a pond 👍🏻
Hi. Your pond looks awesome. The filters are massive - impressive moving bed. Can not over filter.
My 2 tougths. If you extend the inlet to the pumps with an extended mesh like the oase drum combi might help with the blocking.
Also Like to see the video how you going to clean the settling tank.
5 seconds in..nicely laid out and plumbed.
Thanks so much
I’ve watched all your videos especiely the ones your spawning g breeding koi! Keep the good work up💪👍
Thanks my friend
👍
I have the same problem mate
Wow great set up! Forgive for asking but is your pond made of Reinforced Concrete? And then do you just paint it with a suitable waterproof paint. Here in the UK everybody is obsessed with fibre glass and EPDM liners. I think particularly fibre glass is not environmentally friendly. Would be very interested to know. Your fish look amazingly healthy and water clear to the bottom. Fab!
it's a reinforced wall pretty thick 60cm I think. serious engineering involved. all tanks are fiberglassed
thanks for the vid, are you planning o bakki shower and/or protein skimmer for the pond?
both in time. at the moment just wanted to get it habitable for the fish
Hello. its good one. Let me know the product and company name.
Is this the same pump.
Question for you. How did you decide which pumps to use. Thanks in advance. Arthur
Hi I'm looking at flow of full pond volume every hour. I need high volume pumps that have low wattage. Right now mine do 120w and 18kl an hour
How did you decide to use those pumps and how many gallons per each pump. Thanks Arthur
18500 liters per hour 120 watts each. Makes sense and they cost about 4500 rand
What does rand mean. I’m in the USA I don’t understand. Only USA CURENCY
Hello how deep is your pond sir?
It's 2m
Why the need for a settlement chamber with a drum filter? You're just trapping waste in the water column. The RDF isnt doing what it was intended to.
from what i could see, your skimmers are not working correctly. The idea of a skimmer is to pull the water surface tension which drags everything on the surface into the skimmer.... but with yours, the surface water does not appear to pull the water surface tension.
Thanks, what do u think the problem is
@@koiselectsa it looks as if your skimmer is too low and therefor is not working. the water is free flowing over the submerged skimmer door (flap weir) and most of the volume of water that enters the skimmer is not surface water... its in the name, the surface water should be what is being skimmed from the pond... as for your other skimmer, it appears to be at the correct height but i did not see the surface water being pulled into the that skimmer either. Maybe there is not enough water being pumped out of the skimmer boxes, but as you mentioned that you are pumping a lot of water, i can only assume the skimmer door is missing, or stuck fully open, and the other one is definately submerged and maybe something else as well.
it is easy to investigate and figure it out. look in the top access door/clean out and check the flap weir. only surface water should be flowing over it... the inside of your skimmer should have a lower surface height than the pond and the pond water should be flowing into the skimmer box like a tiny waterfall over the skimmer door (flap weir).