Just Put Super Glue on the Led Bulb and you will be amazed
Vložit
- čas přidán 3. 03. 2023
- Just put super glue and baking soda on the led bulb and you will be amazed by how it fixes the dead led bulb and brings it back to life! You can easily try this simple repair tricks at home no tools or soldering welding required.
I hope you enjoy this video of How to TAKE APART and REPAIR an LED lamp WITHOUT A SOLDERING IRON. DIY LED lamp repair.
Nice! You replaced a DED with a home made conductive DED - dark emitting diode with unknown resistance and now the other LEDs may or may not be overdriven 😀 will it cause a fire? Who knows!
Ya. Not exactly a safe practice to be promoting. I'm kinda surprised utube hasn't taken it down.
@@strangelyfamiliar1729 Probably because the LEDs are low voltage.
Sure, the bulb is either 120V AC or 220V AC, but each LED is 3V or less.
However, this would not be a good idea if several LEDs are blown.
@@BlondieSL leds can have voltage drops greater than 3 ive seen 6 and it wouldnt be to suprising if they didnt go higher
@@strangelyfamiliar1729Nah, they're too busy harassing and demonitizing DonutOperater 🍩 😂
Para que todo eso ,Estas fácil remplazar el diodo
How to risk electrocution to salvage a $4 light bulb... this is genius.
More work than the cost of a bulb.
@@CaptainBob42I was able to get LED bulbs at the Goodwill - a box of 4 cost one dollar for 60 watt bulbs.
Here in Arkansas the electric cooperatives donate 4pack led bulbs to habitat for humanity and goodwill to sell for a dollar per 4pack. Keeps good bulbs in people's homes and gives those two organizations a little cash
$4!!?? More like .40¢
@@CaptainBob42 to go buy a new bulb will waste 1 to 2 hours compared to repairing the light bulb which cost less than 30minute if you are expert at the technique (3minute as shown in the video), and at no cost either. You should time what you do, you'd be surprised at the time wasted going to shop.
I don't know that I would recommend it. You probably noticed that it is much brighter than before because after shorting the contacts, you've increased the current through each one.
increased the voltage, not current?
@@paulshlasko3608 Yes the voltage does increase but it also causes the LED's to draw more current. You would notice it as they will get hotter than normal. Most of these cheap bulbs do not employ a constant current in their design.
@@StevenCookFX Thanks!
Fixing an old led. Light strip, using a volt. Regulator. They will handle more voltage. Without issues. Someone thru away' a motion sensor light strip. I wired a regulator adaptor, to voltage regulator. Straight to lights. & turn voltage up 2-3 more than specified. Plugged to a timer. Been working for years.
That’s a hell of a lot of work to avoid having to buy a replacement bulb!
Though I agree it is, it's all about the project, not the product.
how is 3 minute took a lot of work? your hourly-wage divide by 20 (3minute). What is the cost of buying new bulb? hourly-wage times 2 (2hour).
Do they sell solder in your country?
Penemuan ide yang sangat mantap👏
Bagus sekali.. idenya👍
Graphite powder is also sold in a dispenser tube because it's used as a lubricant for many different purposes.
vvörkett häl ön squakey ´Döörce -:-
and is pillce´? vFv
@@cv507 If I translated this correctly, yes, it is good for eliminating squeaks and noises caused by mechanical friction.
"Just put super glue on the LED bulb" Plus 153 other things using every ingredient known to man.
А капельку припоя паяльником нельзя было нанести, чем так извращаться?
Графит имеет небольшое сопротивление в отличии от припоя, именно поэтому лампочка может поработать немного дольше, чем от простого припоя.
Остальные светодиоды уже слегка поджарены, поэтому что припой, что графит - бесполезное извращение.
@@mihailmirov8032
Разницы нет графит или припой потому что драйвер все равно будет поддерживать заданный ток но припаять то легче
@@andrey8688
Согласен: извращение
@@coffeemn8032 ?
Hola boa tarde .
parabens gostei muito.
Eu sou Antonio de vicosa minas.
Now the remaining leds will burn a bit brighter and have less life in them. Why not using a small resistor and prolong the led lives? 😋
I Preffer to replace dead LED with good one (for example from donor bulb) and use multimeter to detecd dead one (not metalic tweezers) and of course not under current! Superglue is good to glue plastic cover back...
excellent
It would have been a lot easier and a lot of less time to have soldered the end of the not working chip to make the circuit and nothing more.
Complimenti davvero idea ottima,mi mancava 👍👍👍💯👏👏👏
I think I'll just buy a new light, instead of going through this hassle.
Yeah no joke! Not even close to being worth it
There are some people that unfortunately cannot afford to buy a new light bulb, but might have graphite and glue lying around. This could mean the difference between light or none.
Potevi fare direttamente un ponticello di stagno sui terminali del led bruciato ed gli altri si accendevano lo stesso. Chi garantisce che la caduta della corrente sulla mescola che hai fatto (se c'è) sia uguale con gli altri led? Perché in questo modo aumenti la corrente sui altri Led e saranno destinati a una vita molto corta. L'unica soluzione valida è sostituire il led bruciato, e se riesci aggiungere ancora uno in più nella serie, succede che abbassi la corrente sui ogni led, così aumenti la loro vita.
unbedingt gelbes Isolierband nehmen !!! Die LED Lampe wird nach der Reparatur aber nicht mehr lange halten, da jetzt alle restlichen LEDs zuviel Strom kriegen und durchbrennen.
…oder die restlichen LEDs sterben eher an Überspannung, wenn es eine Reihenschaltung ist.😊
how about soldering a bridge connection with a 30 gauge wire? Better solution.
nope. Why do people offer suggestions that know nothing about electronics? Especially when sometimes it could lead to damage or worse.
Umständlicher geht wohl kaum noch! Was für ein Supertipp!!!
Vielleicht umständlich, aber - wenn's funktioniert - auf jeden Fall nachhaltig! 👍
Es geht nicht um die Nachhaltigkeit, sondern die Art der Reperatur. Hättest auch draußen Rost von Metal kratzen könnnen, diesen Rost mit Rostumwandler wieder in leitfähiges Metal umwandeln können, dann dieses in feine Späne zermalen mit leitfähigem Bindemittel versehen und das als Lotersatz nehmen können.
Vielleicht etwas umständlich, aber auf jeden Fall nachhaltig!
Should have a voice included to know the name of the products used.
Should have used a voice to warn you you are overdriving the circuit and could cause a fire in your beloved home.
Don't do it!
@@DanBlackRacingwho said it was for their own home?
Showing a dumb solution without any explanation + give it an even more stupid title. YT in 2023.
Anyone, who DOES REALLY understand, what is happening in this video, is also able to de-solder the defect LED and replace it by a new one or some diode with similar specs of a resistor, matching the voltage loss in the circuit.
But solving the issue by mixing some obscure combination of - I suppose - baking powder and graphite, which will give an unknown resistance + harden it with CA, which might burn and ignite the whole plastic bulb/shell ... that's a no-go!!!!!
Exactly. I wouldn't click on the video, but I was curious, what people say in the comments... To my disappointment many people think this is a good solution. It's really not.
He's also playing around live mains voltage and doesn't give any warning in the video! :/
De-soldering on these aluminium clad boards is not as easy as you mught think even with a fairly hefty iron. Try - you might be surprised at just how awkward they are to work on - as the aluminium substrate works as a giant heatsink!
@@guyteigh3375 80w + massive tip + silver soldering wire (lead-like melting temperature)
I noticed that when blobbing solder onto the open trace after scraping the dud led off.
It was a real pig to make the solder bead stick and i had to preheat the board with the iron first and use flux
I feel like Mr. Wonderful trying not to get angry after watching this
I remember we used to fix TV backing lights and we did something similar.
Это дорого !можно использовать фольгу от шоколадки +изолента, замкнуть контакт светодиоды который сгорел
а проводок слабо взять и не выёживаться с пинцетом и изолентой.
ᵃ ʸ них ещё паяльников не изобрели
Доктор Дью придёт в восторг от этого лайфкака )
А впаять рабочий светодиод слабо?
Folyo bant yapıştırsan yeterliydi. Ancak o ampül kısa sürede patlar yine de.
BRAVO
А спаять дорожки не проще?
Графит имеет небольшое сопротивление в отличии от припоя, именно поэтому лампочка может поработать немного дольше, чем от простого припоя.
@@mihailmirov8032 не факт что дольше, по своему опыту, есть у меня лампы которые светят уж около года с спаянными дорожками сгоревшего светодиода, а сгорел один светодиод в лампочке отработав месяца три. Есть конечно лампы которые горят по несколько лет, и норм. Здесь как повезет, пути господни неисповедимы)) и потом, если графит имеет сопротивление он может греться, возможно и не хило
@@user-ij2oi2dj9j Раз на раз не приходится?!
@@mihailmirov8032 согласен))
So the title of this video should be:
What is the quickest way to get to the intensive care unit.
I totally agree with you on the idea of sustainability. repair instead of buying new. but this can be life threatening. even with low power supply. every body reacts differently. then rather make a video in which the right tool is at the start and a note at the beginning of the video.
Si ahora hay menos resistencia y más corriente por los LEDS ,por lo que se fundirán más rápido.
correcto lo realize con soldadura y solo dura 3 dias lo recomendable es conseguir otro led y ponerlo o alguna resistencia.
This was entertaining to watch. But I am just gonna toss that broken bulb and buy a new one.
exactly the point and safe too 👍
@@thonrioflorido4316 I spend less time cooking thanksgiving dinner.
You may have money, but not a creative mind.
@@Valahlawnmual-mc8iz Money buys creative minds.
@@Prabhu2086 but you can't buy it for yourself, you just can buy the works.
Qué es esa cosa blanca, sal, bicarbonato, harina qué es ? Yo vi, que otro señor le ponía en pedazo de aluminio y lo cubre con aislante.
Интересно! А долго так лампа проработает?
Кому как повезёт... Я паял не одну - некоторые горят несколько месяцев, а изредка какие-то всего 5 минут.
How many people do you think will get an electrical shock trying to save a $2 LED bulb? This is the opitomy of "cheap bastard" ... sometimes its just easier to buy a new one. I'll add this to my list of "things i'll never try" ...
Don't you own a soldering gun?
It's best to buy just another one
And on the tips and hacks we will be showing you how to make a home made fire extinguisher for those annoying electrical fires.
У вас наверное за качеством следят , а у нас всё китайское , отвратительное качество товаров
The remaining LEDs will overvolt slightly buf if they have a large tolerance range they will be fine.
The amperage remains the same so there is no fire risk from overheating but as some have said on here a small resistor is a more elegant way of doing it.
I would just blob the the open trace with solder and be damned with a fast and dirty fix as it is not worth any more time and attention than this.
The bulb was cheap trash anyway so a blob of solder and squirt of glue is all its worth and time spent on it remains killed.
@@MrDegsy69 Actually the next weakest LED will fail. I have worked with these LED's and they are not forgiving. The circuits they employ are cheap and do not do constant current. So no you are incorrect the current increases.
LED bulb output 10 to 20 watt of power, it doesn't output enough energy to create fire. For comparison if you had hot-iron for soldering that is 10watt, you will never reach sufficient heat to solder, so how can LED light bulb with such power catch fire?
Lehim yapabilirdin.Ayrıca bu şekilde arızalı ledi kısadevre edince devredeki diğer ledlerin gerilimi artar ampul kısa süre sonra tekrar arızalanır.Kısa devre yerine arızalı ledi değiştirsen daha iyi olurdu.
Akım kaynağı artık. gerilim otomatik ayarlanıyor.
Que es ese polvo blanco?
What is that white powder uou use ??
Small cobber wire around the dead diod I've seen work amd fast.
works till the next weakest LED burns out.
What was that aerosol spray that was sprayed on the superglue?
Water. For faster hardening.
Activator
Good job 👌
What’s a bulb like that cost three bucks ? You’ve got about five dollars for the repairs there. Not counting labor.
Que' es el producto blanco que se mezcla con el grafito de la mina del la'piz ...
Most LED bulbs are designed to fail, as the LEDs are over driven, shorting a LED is making its life worse. A better thing to do is, remove one of the two resistors, that over drive the LEDs and lower your electric bill 💡
Very interesting. Im sure if i did it, id learn something, but id never have the time. Its 1:45AM, and im just eating dinner (cold)
Quello bianco è sale o bicarbonato?
А что еще добавили в порошок
Wow amazing
Did he just touch 230 V with a conducting pincher which had some electric tape on it? Or maybe it is 110 V?
serbuk putih itu apa bang
All i can say is you must have a lot of time on your hands...lol Good job
And sincerely - I hope this dude has a good health plan. The way he solved problems will inevitably lead to others - sooner than later.
.... mi piace, ma alla fine cosa hai spruzzato?
👍👍👍👍👍👍👍
Why don't you use a soldering iron? Solder them together in 5 minutes and you're done. You don't need a pencil, sandpaper, or glue. Today, soldering iron can be found in every home.
another person who has no electronics knowledge giving bad advice doesn't help. The bulb will run for a few mins then fail again as another led will burn out.
Столько лишних действий, просто паяльником можно выпаять старый диод и напаять олово.
Before cutting into a PVC pipe, mark the area to be cut and use a pipe cutter or saw to make a clean, straight cut.🤩
what
I use a table saw. MUCH quicker. Just….make sure it’s not still attached to the outlet when doing so…..RIP Uncle Steve.
@@Nosroc2004 Ol' Uncle Steve had a really electrifying personality.
@@felixmadison5736 get I am not your uncle... J/K heheh
Where is he cutting into PVC? that plastic on the bulb is not PVC it has a higher temp range and allows light to diffuse from the LED's through it.
Why not buy a new bulp, than risk of being electrified or burning your house down.
Sir, may i know what is the white thing mixed with the pencil lead ?
It appears to be baking soda. commonly used with superglue. Don't do this btw its stupid. Either get someone to help you that knows electronics or go buy a new one. Not worth a fire hazard.
😊 some people ain't got the money to just go and buy a $4 $5 lightbulb better than sitting in the dark
Are you kidding? You can literally pick these up for a quid a dollar..... anyone can afford it.
If you can't afford a 25¢ bulb, then you can't afford the electric to keep it turned on either.
Dollar stores sell lightbulbs for $1.25
way more info is needed and if that pencil was supposed to have been made of lead, well...
Egy csepp forrasztó is elég lett volna vagy egy kis darab alufólia.
What is the white powder
Japanese Techonlogy
А не проще ли капнуть каплю припоя на зачищенное место и не переводить карандаш и клей?))
Конечно проще. Это каждый сможет. Но зачем же просто, когда можно сложно?
All depends on what your time is worth right, a bulb is less than $5 but true we live in a disposable culture.
پینسل کے کارٹون میں وائٹ کلر کی کیا چیز بنائی ہے
What is the white powder you mixed with the pencil core ?
Carbonato
Baking soda, it hardens the super glue. The graphite makes the mixture conductive.
hope
What was the white powder you mixed with grafit
Baking soda, it hardens the super glue. The graphite makes the mixture conductive.
Je suggère vivement d'ajouter un avertissement clair sur le risque d'électrocution. A la première électrocution avec ou sans conséquence, l'apprenti sorcier ou sa famille peut attaquer en justice !!!
Anyone who does this in their home, and doesn't care if they burn it down, then have at it!
There's no danger in this! All he's doing is bypassing the dead cell. Don't you know these run on DC anyway?
@@SerpentLord Yes, but I have heard of them catching on fire.
Great! There are inventors who, through their groundbreaking ideas and inventions, change the world and improve our lives in incredible ways. I admire one such inventor for his creativity and ingenuity. His inventions have revolutionized so many areas of our lives, from the way we communicate to the way we perform medical treatments.
It's hard to imagine how different our lives would be without this inventor's inventions. He is truly an inspiration, someone who has positively influenced the world in such a significant way. His incredible contributions to society have shown what is possible when one works hard and uses their imagination.
I am grateful for his work and for showing us how far-reaching the impacts of inventions can be. His work will forever be a part of human history, and I am proud that there are inventors out there who can change the world.
Wow. You created another account to pat yourself on the back for such a dangerous and lame fix? haha
Ok good job Timmy B+ set it on my desk, and go on to recess.
@whollenbeck8 I was literally thinking that too!😂
Not a good idea to fix a bulb like that, but, you did give me an idea of how to fix a flexible circuit board.
Depending on the flexible circuit board. if its one of those ones that cannot be heated or it curls up then you need to get the special tape. It only lets current flow one way and they use it for flex cable on Phones etc.. (mostly the LCD glass) google - Anisotropic Conductive Film (ACF) or tape
better to buy a new one
Nice, but that's a lot of work to rescue a dead bulb.
What was the white powder?
baking powder
Cocaine.
That's the secret.
Il n'y a pas que du bicarbonate et de colle...?
And how many men does it take to change a lightbulb?
Ma la polvere bianca, cos'è, bicarbonato? E quale funzione avrebbe?
I just wasted 30 min of my life ? That's what I learned
ممتاز .
So what was the white powder added to the graphite? Salt, sugar, baking powder, what?
Baking soda, it hardens the super glue. The graphite makes the mixture conductive.
What the flip is the white powder!
The remaining LEDs will burn out faster because the chip will still output the previous amount of current. Why waste so much pencil if you needed only a little bit? Is the remainder of the powder for future use?
What is the white powder mixed with the graphite?
I wondered that too. Not terribly helpful.
Называется карбонат натрия.
Нанесите это на лампу и будете поражены электрическим током! 😂
Проще выкинуть лампочку нафиг, чем так извращаться
Im just removed those broke led then soldering it much more easier
How much time, that led continues working?
Why not try it for yourself instead of pouring negative criticism and scorn?
My cups half full but you appear to have pissed in yours!
What is that white powder at 2:22?
Methamphetamine
Why don't you explain what you are doing?
Проще оловом капнуть ☝
Графит имеет небольшое сопротивление в отличии от припоя, именно поэтому лампочка может поработать немного дольше, чем от простого припоя.
So .. there's no risks of fire hazard doin this ?
I wouldn’t mess with electrical things. It could become a fire hazard.