Backup saving parameters on a Fanuc 0-TC control, Miyano CNC Lathe, CNC Digital, Inc.
Vložit
- čas přidán 19. 12. 2020
- Backup or saving parameters on a Fanuc 0-TC control.
Download to your PC.
Fanuc Parameters 2.0=1 which equals two stop bits.
and Parameter 552 = 10 = 4800 baud rate
These two parameters must match what is in your PC software for file transfer.
Miyano CNC Lathe,
CNC Digital, Inc. 440-721-7100
www.cncdigital.com - Věda a technologie
Thank you so much for you video. Can you share the parámeter with me.? Please?
Thanks all work great!!
What is the name of that software? Where can I get it from?
Please help me how to backup ladder program of fanuc 0 series
Thank you very much!
You are welcome!
Hi@@cncdigitalCNCMachines
Hey! Why didn't you press EOB when downloading the diagnostics?
And what was that you explained at the end about parameter no.1 and 502 and 503. Can you please explain it into simple words. I will be very grateful.
The bit at the end was regarding the serial communication settings. This should be established before transferring files as you need both the control and pc to have matching settings. These include the baud rate, data bit length, stop bit length. Hardware handshake etc. If your coms settings work and you can transfer files via rs232 then you can ignore those settings as they are fine.
Hi! May i have the configuration for the Rs 232 25pin -Usb ? Does it need a special hardware to connect the pc to the machine as shown in this video.
No. I purchased the cable on ebay. Just searched for RS-232 to usb CNC cable.
Thank you for the very informational video! Do you have the procedure for loading the parameters back into the machine? One of our machines has had the Delete+Reset command done to it and im starting fresh. I was hoping I could copy the parameters from my identical machine and load them into my wiped one.
I do not have a video.
However.
INPUT OF SETTING PARAMETERS PROCEDURE
PRESS DGNOS/PARAM KEY
(SETTING PARAMETERS INPUT)
(MAKE SURE SETTING PAGE 1 ARE CORRECT)
ISO=1
I/O=0
E-STOP PRESSED IN
PWE=1
MEMORY PROTECT KEY OFF (TO THE RIGHT / )
MODE SWITCH = EDIT
ENTER 900 OPTION PARAMETERS BY HAND
CYCLE POWER TO ACCEPT OPTION PARAMETERS
E-STOP OUT
PRESS INPUT LSK SIGNAL FLASHES (LOWER RIGHT SCREEN)
SEND DATA FROM PC. INPUT SIGNAL FLASHES (DATA BEING ACCEPTED)
INPUT PC DIAGNOSTIC PARAMETERS, TIMERS, COUNTERS.
PRESS DGNOS / PARAM KEY TWICE.
(MAKE SURE YOU ARE IN DIAGOSTIC SCREEN)
(MAKE SURE SETTING PARAMETER PAGE 1)
ISO=1
I/O=0
MEMORY PROTECT KEY OFF (TO THE RIGHT / )
MODE SWITCH = EDIT
PREPARE CONTROL TO RECEIVE DATA (WAITING)
PRESS INPUT LSK SIGNAL FLASHES (LOWER RIGHT SCREEN)
SEND DATA FROM PC. INPUT SIGNAL FLASHES (DATA BEING ACCEPTED)
@@cncdigitalCNCMachines Thank you for your reply! I had actually figured it out on my own but I know that this will be helpful for many others.
@@chrishopkins7620 Do you have a backup? We had the same problem with the reset but no backup
Dou you know how to change the direction of clamping of that machine in the parameters screen?
Reverse hydraulic hoses. Or there is a quick disconnect.
This is a great video! I am having problems that the code is coming out in machine language instead of values that I can read any ideas?
Call to discuss 440-721-7100
Hai sir , let me know how to backup plc also
Ge fanuc o-m series
Ot backup
Hi Sir! Can you send to me this Software.Thanks
This is paid for software. We do sell it or have the ability to give it to you. Sorry.
What is the name of the software used here
@@cncdigitalCNCMachines i would like to buy one too, but how?
Hi