This is such a great idea that it's hard to believe the planer manufacturers haven't actually released their own attachments for this or designed the planers to support it. Drastically more efficient than the router-based approach that so many people seem to be using. Thanks for sharing!
@@JohnPatersonAu That was my thought too. The only ways to adjust the depth with this is minor adjustments with the knob and larger adjustments with shims. Router seems easier, though slower.
@@blakeshedd5354Shims to raise the work-piece should be easy enough with standard aluminium sheet. Cut small plates or discs for the corners in 1mm, 2mm, 3mm, etc.
No matter how long something has been around, and people think that every facet has been figured out- there is always something else to invent. Genius work my dude
@@shawnmann9491 undoubtedly! I'm in the process now of doing this with linear rods and bearings. The edge guide holes and brackets are perfectly positioned for it. I'm actually putting it on a base so that it lines up on my bench and is held in place with dogs I'm putting on the bottom. Now it'll just be a matter of depth settings and boom... let the shavings begin!!
@@carterscustomrods . Very good info Sir! So you are mounting it upside down🧐? I was going to investigate his depicted planer, and will look into your model as well. I’d love to see a picture of your finished setup! Happy New Year to You!
Удачная конструкция рейсмуса. Браво. За аккуратность. Необходимо сделать регулировку платформы для изменения толщины доски. Можно сделать винтовую регулировку ножек платформы в пределах 30 мм. Это реально при аккуратность мастера. Станет универсальным приспособлением.
I have a hand planer like yours. I have had it for close to 25 years. Lost the manual. Never new how to properly aline the blades until I watched your video. Thaks for posting. Love your videos.
This is a pretty solid little workbench. While once you figure out how it comes together, it is physically Easy to assemble czcams.com/users/postUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh by yourself. But the diagrams explaining the steps are really pretty bad. I could not get the handle pins in all the way despite multiple attempts, so I just used a screw I had on hand for the 2nd handle. I could not get the first pin in further or pull it back out. You are supposed to hammer it in, but I had no leverage and the handle is plastic and I did not want to risk breaking it. I will get a lot of use out of the bench because of the convenient size and height. It does fold up nicely for storage. They even explain how to fold it so you don't get pinched...that is important!
@@renem8130 yeah because of the variation in grain direction you should definitely go with the router, remember to have sacrificial prices of wood on the entrance and exit end of your path with the router tho to make sure your table top has 0 tear out :)
Excellent! I've been wanting a planer, but can't afford the benchtop kind. However, I did buy an electric hand planer similar to that, but I haven't had much success with it. This, my friend, is a game changer! Great idea, thanks for sharing!
Portable planers cannot flatten a timber slab, so this method is the best way to go. You also need shims for each corner of the slab. to raise it in 1mm steps. 4 x 1mm, 4 x 2mm 4 x 3mm, etc. Make a cut with 1mm shims. Reset the job with 2mm shims, make another cut and so on.
Funny, but my father did a similar thing , with castor wheels, with an electric planer 35 years ago! Too bad there was no CZcams back then! Great video 😱😂👍
‘I flattened a bench top with a router but as you say this seems way easier. I think that it is important to have sharp blades in the plane. Also I fancy that his method of mounting the plane on the rails was more complicated than necessary.
Totally agree, my dude is terrifying to watch on the table saw. Seriously brother, the reach overs, narrow pushes on finger tips with angled cuts, insanely dangerous.
Was trying to do something like that for a long time, in the end I got 2 HGR20 rails and made a router sled. Absolutely love what you did 😃👍⭐️⭐️⭐️⭐️⭐️⭐️.
Did this with the Bosch 2632 and 20mm linear rods (I originally did it with V-slot and uhmw backed guides, but it would wobble). The linear rods keep it locked parallel, and can be rigged for all sorts of setup design, but they're $$$ 😞 . But if you get the right diameter, a shorter length can be used, and just require more adjustment.
This can come very handy to me that I’m just starting woodworking as a side hobby and I already own an electric hand planner, matter of fact I own this exact model, Makita I believe? Thank you, love your channel
I was on the fence about getting an electric hand planer after my first failed project and don't have the room for a full sized planer. Thank you so much for this video! I feel dumb for asking but what's the clear stuff you use to apply the block to the back of the hand planer? Silicone caulking?
Лутше рейсмус купите. Пусть самый дешовый. А с этой хренью упаритесь. Хороша только в одном случае, когда толшина не принципиальна. Банально 1мм упаритесь ловить.
One thing very few people noticed, is the GREAT use of the MAKITA Model 1912B Planer, which is WIDER that the standard electric hand planer: (4 3/8" versus only 3 1/4")... this makes it much better than using the common 3 1/4" hand planer. That model is very powerful, precise and solid, and its baseplate is bigger, giving a better, flatter planning. ITs only drawbacks are that Makita only has High Speed Steel blades in 4 3/8", which have a less hard and durable edge, although those can be conveniently resharpened thanks to the guide included in the planer; and that the shavings discharge port is not round, making it difficult to connect the the vacuum, otherwise it is a unique and wonderful machine.
I appreciate your knowledge! Not sure I'd necessarily want a wider one for many projects....surprising that they'd design an ejection port that wasn't round!! Very odd...I have a Bosch....using it for years, but I wish had a battery powered Makita....I think it also has better placed threaded sockets on the sides, for attaching "homemade" gizmos like rails...
@@samuelluria4744 ADDING threaded inserts to the sides (or top or front/rear) of the tool body is easier than you may think... I have used those threaded inserts meant for wood, with coarse threads outside and machinescrew threads inside, both in 1/4 20 and 5/16 18 (larger preferable!), because those are readily available here in Mexico. But I plan to investigate in detail the "E-Z Press™ Special for plastic" inserts. On my large MAKITA 1912B 4 3/8" wide planer, I am planning (pun intended!) to cut some threads into the thick aluminum sole plate, because those would be even firmer than attaching screws into the insert into the plastic body of the planer, and the thick base plate allows plenty of room. By designing a good adjustable height mechanism, this can result in a quite precise adjustment, and that could mean an inexpensive tool many times more affordable than a Bench Planer or Edge Jointer. The several excellent videos from a couple of extraordinary Japanese (or Oriental) carpenters, show clearly that, working with patience and dedication, precise enough bench tools can be made with wood or combined materials from inexpensive electric hand tools.
@@alfredomarquez9777 - Wish you the best on your projects!!! This is something I will have to do at some point! As a side note, does anyone in your area work with a sanding table? There are some factories near me that use them industrially, but they'd charge an arm and a leg for piece work....
Hello, great video plus brilliant idea ? The Makita Power Planer I own is the 1100 model. Do you think it might work the same way to build-up the assembly ? Thanks, Robert
NOT the least bit effective imho ! No explanation whatsoever AND even worse, no links for any hardware (that he MAY have used) !NOT EVERY WOODWORKER WATCHING THIS HAS YEARS AND YEARS AND YEARS OF EXPERIENCE !
Good build, but ROLL YOUR SLEEVES UP when working on the tablesaw, you were in great danger of having your arm pulled into the blade if the sleeve had been caught by it.
ah I got this boss planer. It's got two threads on the front and this red plastic thing underneath which you can place a rod or so, now I know where it's for haha, very helpful!
Hey, I got the same planer! Was always wondering why I bought it in the first place, it's not a very useful tool at all (not even for finishing, as it can't be dialed to zero depth). Now I see that every impulse buy has a purpose in the end...
Do yourself a favor and buy the makita 1912B model, because it is wider and longer. Its 4 3/8" width blades are way more convenient than using a smaller, standard hand planer. I have it, and feel it is a way better buy considerning its size, weight, solidity and powerful motor. I have not seen any other larger than 3 1/4" wide electric hand planers. Makita has a monster one at a full 6" width, but it is expensive and not available in my country, but the 1912B is still very convenient overall.
TY 4 the brainstorming ideas,showing me what not to do / how to make the jig simpler. Also, you should review your video to count how many times your hand passed over the saw blade to place the wood on the other side of the fence!
Great minds must think alike. I did something very similar when i wanted to make piece of wood round. My solution was more temporary than yours and by the looks of it mine was heavier which in retrospective was a bad thing because it knackered me after about 20 mins. But once you have it made and set up it works a treat well done.
Raise your hand if you've ever used one of these hand planers and "planed" the cord on the backstroke... 🖐 ⚡⚡Thanks for the cool video. I like the idea.
Man, I was just trying to imagine a way to do this and you nailed it! But I think a router sled is much simpler and easier to adjust cut depth (I imagine), so I'll probably do that, but still awesome job.
@@devonswindell9735 In my case that's a good thing. I tend to take too much off when I'm using the planer. I can't seem to ever get it right. Maybe I'll have more success with my planer. I keep gouging the wood at the ends. I really want to use my planer so I'll try this for sure.
Well, there’s definitely enough people on here pointing out how close you are to that blade (they’re right). Done careful, fingers are hard to reattach after they’ve gone through a saw... However, I have one of these planers, and wondered how to get it to work better. I have a router too, but I’m going to try this, it’s a great set up!
how unpredictable do you expect a table saw to behave with a sharp blade and cutting soft wood? I mean it's not a 100 years oak peace or anything. Simple pine is soft and nice to work with, saw cuts through it like a hot knife through the butter.
A bit of setting up to do but after that you get a beautiful finish.Have you thought about putting a spiral blade on or are you happy with the straight blades.
This is such a great idea that it's hard to believe the planer manufacturers haven't actually released their own attachments for this or designed the planers to support it. Drastically more efficient than the router-based approach that so many people seem to be using. Thanks for sharing!
Thanks for watching sir.
Can I save this or get the plans for it
I agree, but I think adjusting the depth would be easier with a router sled.
@@JohnPatersonAu That was my thought too. The only ways to adjust the depth with this is minor adjustments with the knob and larger adjustments with shims. Router seems easier, though slower.
@@blakeshedd5354Shims to raise the work-piece should be easy enough with standard aluminium sheet. Cut small plates or discs for the corners in 1mm, 2mm, 3mm, etc.
No matter how long something has been around, and people think that every facet has been figured out- there is always something else to invent. Genius work my dude
Thanks for watching sir.
I am surprised this dude has all of his fingers!
Sorry about that. I'll be careful. Thanks for watching sir.
🤣 🤣 🤣
I had some concerns as well, but this idea is pure genius IMHO😎.
@@shawnmann9491 undoubtedly! I'm in the process now of doing this with linear rods and bearings. The edge guide holes and brackets are perfectly positioned for it.
I'm actually putting it on a base so that it lines up on my bench and is held in place with dogs I'm putting on the bottom. Now it'll just be a matter of depth settings and boom... let the shavings begin!!
@@carterscustomrods . Very good info Sir! So you are mounting it upside down🧐? I was going to investigate his depicted planer, and will look into your model as well. I’d love to see a picture of your finished setup! Happy New Year to You!
Удачная конструкция рейсмуса. Браво. За аккуратность. Необходимо сделать регулировку платформы для изменения толщины доски. Можно сделать винтовую регулировку ножек платформы в пределах 30 мм. Это реально при аккуратность мастера. Станет универсальным приспособлением.
Wow, I have one of those planers collecting dust in my workshop that now will have a new purpose. Thanks for posting this!
I have a hand planer like yours. I have had it for close to 25 years. Lost the manual. Never new how to properly aline the blades until I watched your video. Thaks for posting. Love your videos.
This is a pretty solid little workbench. While once you figure out how it comes together, it is physically Easy to assemble czcams.com/users/postUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh by yourself. But the diagrams explaining the steps are really pretty bad. I could not get the handle pins in all the way despite multiple attempts, so I just used a screw I had on hand for the 2nd handle. I could not get the first pin in further or pull it back out. You are supposed to hammer it in, but I had no leverage and the handle is plastic and I did not want to risk breaking it. I will get a lot of use out of the bench because of the convenient size and height. It does fold up nicely for storage. They even explain how to fold it so you don't get pinched...that is important!
I came across this looking for something else but this is exactly what I need for a big project I'm planning for this winter. Thanks!
YES!!! Now I can finally make that live edge wood wall shelf for my best friend. His wife will be so happy.
Pleased to hear that.
Thanks for watching sir.
That's what she said.
lmao! That's slick.
This makes so much more sense than a router version. Super smart.
Thanks for watching sir.
Yep, might have to give this a try. Four days with a router Vs 5 minutes with a planer 🤣
The router version is gonna still be much better for end grain or going against the grain of a peice
@@Festoos that's what I was thinking. I have a table top to even out, but I have a bread board glued on already. It won't go well with a planer huh?
@@renem8130 yeah because of the variation in grain direction you should definitely go with the router, remember to have sacrificial prices of wood on the entrance and exit end of your path with the router tho to make sure your table top has 0 tear out :)
Excellent! I've been wanting a planer, but can't afford the benchtop kind. However, I did buy an electric hand planer similar to that, but I haven't had much success with it. This, my friend, is a game changer! Great idea, thanks for sharing!
Thanks for watching sir.
Portable planers cannot flatten a timber slab, so this method is the best way to go. You also need shims for each corner of the slab. to raise it in 1mm steps. 4 x 1mm, 4 x 2mm 4 x 3mm, etc. Make a cut with 1mm shims. Reset the job with 2mm shims, make another cut and so on.
Oh my goodness J! This is genius and WAY better than doing this with a router.
I'm happy to have made this idea.
Thanks friend.
@@j-woodworking9573 uuuu
Funny, but my father did a similar thing , with castor wheels, with an electric planer 35 years ago! Too bad there was no CZcams back then! Great video 😱😂👍
Fabuloso, esse dispositivo fico muito funcional, olha...., estou pensando em fazer um deste!
Abraço aqui do Brasil 🇧🇷
Thanks for watching sir.
you always amaze me with your brilliant ideas!
Thanks for watching sir.
This is brilliant.
I did the same trick with a router but this is way better!
Thank you for sharing!!!!
Thanks for watching sir.
‘I flattened a bench top with a router but as you say this seems way easier. I think that it is important to have sharp blades in the plane. Also I fancy that his method of mounting the plane on the rails was more complicated than necessary.
@@billgiles3261 ..ㅈ
You definitely are a thinker! But watching you on that table saw after losing the tip of one of my fingers made me sweat! Good job in and the best.
Sorry to hear that. I'll be careful sir.
Sorry to hear about your finger. How deep was the cut? Did you lose the part of finger completely?
Man, same sweaty fingers here too. Cut 3 of my fingers myself a few months back & watching it get so close, skipped a lot of the video.
Yeah, watching that table saw work @ double time was er... triggering. The splitter looked like the saw blade in some of the shots as well.
Totally agree, my dude is terrifying to watch on the table saw. Seriously brother, the reach overs, narrow pushes on finger tips with angled cuts, insanely dangerous.
Was trying to do something like that for a long time, in the end I got 2 HGR20 rails and made a router sled. Absolutely love what you did 😃👍⭐️⭐️⭐️⭐️⭐️⭐️.
Thanks for watching sir.
I always wonder why so many people make router sleds, when planer sleds make so much sense....🤷🏻♂️
That is amazing ingenuity.
Very well done, amazing how you used the electric hand planer.
Never seen it done with a planer. Made a few router sleds for surfacing in the past. Nice work
Excelente ideia , genial , parabéns belo trabalho .
Thanks for watching sir.
Brilliant idea to turn this simple hand planer into a jointing and thicknessing planer!
Love it. It's like a router jig but with a hand planer instead. Nice.
Взял на заметку! Спасибо, хорошая идея и исполнение.
Thanks for watching sir.
@@j-woodworking9573 igsrp
@@j-woodworking9573 wst
자동대패를 살까했는데 이 영상을 보니 망설여 지네요.
정말 좋은 아이디어입니다.
자동대패는 필요합니다 적당한 사이즈로 구매하시고, 가공이 않되는 특별히 큰 사이즈를 이 지그로 가공하면 됩니다
감사합니다
Beautiful work. Thank you for the inspiration. Time to get to work on my own design for my needs. Cheers.
This is a brilliant idea! Thank you for sharing this. Greetings from Oregon!
Did this with the Bosch 2632 and 20mm linear rods (I originally did it with V-slot and uhmw backed guides, but it would wobble). The linear rods keep it locked parallel, and can be rigged for all sorts of setup design, but they're $$$ 😞 . But if you get the right diameter, a shorter length can be used, and just require more adjustment.
This can come very handy to me that I’m just starting woodworking as a side hobby and I already own an electric hand planner, matter of fact I own this exact model, Makita I believe? Thank you, love your channel
Goste muito que projeto éselete parabéns meu amigo
You just saved my a lot of money!!
Brilliant idea, gonna give it a try for sure. Thank you for sharing.
Happy to hear that.
Thanks for watching sir.
Parabéns pelo magnífico projeto! É a primeira vez que vejo um projeto como o seu. Muito obrigado por compartilhar as suas ideias.
Thanks for watching sir.
수압대패만큼 만족도가 나오는지는 모르겠지만 부상위험은 확실히 적을듯요
따봉입니다! 놀랍네요 ㅋ 안그래도 전동대패로 판재가공하는 방법 없나 고민중 이었는데,
저도 좀 더 고민 해봐야겠어요 ㅎㅎ
Very clever. Thanks for this. That said, your safety protocols need some work. I really struggled to watch you with that table saw.
Sorry about that. I'll be careful.
Thanks for watching sir.
I was on the fence about getting an electric hand planer after my first failed project and don't have the room for a full sized planer. Thank you so much for this video! I feel dumb for asking but what's the clear stuff you use to apply the block to the back of the hand planer? Silicone caulking?
Yes it is silicon.
Thanks for watching sir.
@@j-woodworking9573 Does the silicon make such a tight bond with wood? Doesn't it fall off after a while ? Sorry for the dumb question here.
I think acrylic mastic/adhesive does a better job than silicon sealant. It's used in car body shops under names like Tiger Seal.
Excellente vidéo.
Simple et fonctionnel !
Merci pour ce partage.
Salutation de France.
Thanks for watching sir.
Хорошая идея если нет рейсмуса, надо будет повторить 👍!
Thanks for watching sir.
Лутше рейсмус купите. Пусть самый дешовый. А с этой хренью упаритесь. Хороша только в одном случае, когда толшина не принципиальна. Банально 1мм упаритесь ловить.
@@j-woodworking9573 omoo
@@j-woodworking9573 o
I've been looking for a jig such as this to flatten slabs with my hand planer that are too wide for my 735. Thank you!
I believe that would work way better than a router sled... thanks for sharing... God bless
Awesome technique, superbly done ✔️
One day, long ago, I bought an electric hand planer. I used it once or twice. But now I know what I can do with it, Thanks for the idea.
Thanks for watching sir.
One thing very few people noticed, is the GREAT use of the MAKITA Model 1912B Planer, which is WIDER that the standard electric hand planer: (4 3/8" versus only 3 1/4")... this makes it much better than using the common 3 1/4" hand planer. That model is very powerful, precise and solid, and its baseplate is bigger, giving a better, flatter planning.
ITs only drawbacks are that Makita only has High Speed Steel blades in 4 3/8", which have a less hard and durable edge, although those can be conveniently resharpened thanks to the guide included in the planer; and that the shavings discharge port is not round, making it difficult to connect the the vacuum, otherwise it is a unique and wonderful machine.
I appreciate your knowledge! Not sure I'd necessarily want a wider one for many projects....surprising that they'd design an ejection port that wasn't round!! Very odd...I have a Bosch....using it for years, but I wish had a battery powered Makita....I think it also has better placed threaded sockets on the sides, for attaching "homemade" gizmos like rails...
@@samuelluria4744 ADDING threaded inserts to the sides (or top or front/rear) of the tool body is easier than you may think... I have used those threaded inserts meant for wood, with coarse threads outside and machinescrew threads inside, both in 1/4 20 and 5/16 18 (larger preferable!), because those are readily available here in Mexico. But I plan to investigate in detail the "E-Z Press™ Special for plastic" inserts. On my large MAKITA 1912B 4 3/8" wide planer, I am planning (pun intended!) to cut some threads into the thick aluminum sole plate, because those would be even firmer than attaching screws into the insert into the plastic body of the planer, and the thick base plate allows plenty of room.
By designing a good adjustable height mechanism, this can result in a quite precise adjustment, and that could mean an inexpensive tool many times more affordable than a Bench Planer or Edge Jointer.
The several excellent videos from a couple of extraordinary Japanese (or Oriental) carpenters, show clearly that, working with patience and dedication, precise enough bench tools can be made with wood or combined materials from inexpensive electric hand tools.
@@alfredomarquez9777 - Wish you the best on your projects!!! This is something I will have to do at some point! As a side note, does anyone in your area work with a sanding table? There are some factories near me that use them industrially, but they'd charge an arm and a leg for piece work....
Way more advanced than what I was thinking of, but it definitely works.
멋진 지그네요 전기대패 사용하다보면 많이 씹히던데 잘봤습니다
제 자동대패가 작아서 작업에 지장이 많았는데 조악하지만 해결방법이 생겨 행복합니다.
감사합니다.
Excellent! I am going to be creating a composite beam and you just showed me how to plane the edges.
Thanks for watching sir.
Hello, great video plus brilliant idea ? The Makita Power Planer I own is the 1100 model. Do you think it might work the same way to build-up the assembly ? Thanks, Robert
Pekerja'an yg telaten..salam dari infonesia..
This is what I love about your perspective simple but extremely effective.
Thanks for watching sir.
NOT the least bit effective imho ! No explanation whatsoever AND even worse, no links for any hardware (that he MAY have used) !NOT EVERY WOODWORKER WATCHING THIS HAS YEARS AND YEARS AND YEARS OF EXPERIENCE !
Sorry about that sir.
Genius! Beautifully done!
Thanks for watching sir.
Thanks for sharing this creative idea!
My pleasure.
Thanks for watching sir.
Good build, but ROLL YOUR SLEEVES UP when working on the tablesaw, you were in great danger of having your arm pulled into the blade if the sleeve had been caught by it.
Thanks for your kind advice sir. I'll be careful.
Better advice -> build yourself a run-off table, then no need to reach over and catch work pieces before they fall onto the floor
Watch matthias wandel test on that. It just doesn’t happen on a table saw. Happens on a lathe though
Just love these videos about making copious amount of wood shavings and sawdust ... priceless ... now I can have plenty of fire starting material
Thanks for watching sir.
정말 좋은 아이디어네요 많은 도움이 될것 같습니다 고맙습니다
감사합니다
I think this planer works better than the one with router! Good idea 💡
Thanks for watching sir.
I am amazed this guy has any fingers left
Brilliant! Great design.
It's beautiful to watch work well done. Very smart!
Thanks for watching sir.
나는 당신의 전기 대패질 비디오를 보고 있었습니다...정말 훌륭해요. 나는 60년대 후반에 한국에서 2년 반 동안 살았습니다. 구독했습니다. 감사해요
INTELIGENT TIMPLAR !!!!
Thanks for watching sir.
영상 잘봤습니다!
목공방 창업예정 중인데 좋은 정보얻어갑니다아~~!~!
수압대패 대신 지그 만들어서 사용하면 좋겠네요ㅠㅠ
번창하길 기원합니다.
감사합니다.
Makes me want to work up a lineal rail system like this to use with my little WEN Hand Planer
ah I got this boss planer. It's got two threads on the front and this red plastic thing underneath which you can place a rod or so, now I know where it's for haha, very helpful!
Thanks for watching sir.
Hey, I got the same planer! Was always wondering why I bought it in the first place, it's not a very useful tool at all (not even for finishing, as it can't be dialed to zero depth). Now I see that every impulse buy has a purpose in the end...
Buena idea. Gracias por tus vídeos. Un saludo.
Thanks for watching sir.
I’ve been contemplaining (
Thanks for watching sir.
Do yourself a favor and buy the makita 1912B model, because it is wider and longer. Its 4 3/8" width blades are way more convenient than using a smaller, standard hand planer. I have it, and feel it is a way better buy considerning its size, weight, solidity and powerful motor. I have not seen any other larger than 3 1/4" wide electric hand planers. Makita has a monster one at a full 6" width, but it is expensive and not available in my country, but the 1912B is still very convenient overall.
If I had 1% of that skill.. geeeeez. Great job my guy
Thanks for watching sir.
Так быстрее чем с фрезером для хитрых дел. А рейсмус он и рейсмус. А когда спил дерева ровняешь. Думаю это зророво! Лайк!
Thanks for watching sir.
TY 4 the brainstorming ideas,showing me what not to do / how to make the jig simpler. Also, you should review your video to count how many times your hand passed over the saw blade to place the wood on the other side of the fence!
Great minds must think alike. I did something very similar when i wanted to make piece of wood round. My solution was more temporary than yours and by the looks of it mine was heavier which in retrospective was a bad thing because it knackered me after about 20 mins. But once you have it made and set up it works a treat well done.
Thanks for watching sir.
Buenisimo, great job.
Thanks for watching sir.
excellent idea. now iwont have to buy those expensive ones.thank you
Mantap pisan euy
Dude- you are the God Of Power Tool Guides!
You went too far.
Thanks for watching sir.
great! this way we can ensure a perfectly flat surface!
Very clever! Way better then routing.
This is a fantastic jig!
Thanks for watching sir.
I love this idea. And, I'm obviously missing the blade mounting jig. I have never had one and was wondering where I might be able to get one.
Sorry I don't know either sir.
Super Idee
Dankeschön fürs Zeigen
Thanks for watching sir.
Buena idea...saludos desde ecuador..like..👍
The idea you've come up with is excellent and very beautiful.
Thanks for watching sir.
@@j-woodworking9573 twpittro
Good bosq 👍🏿👍🏿👍🏿👍🏿🙏🏿
Raise your hand if you've ever used one of these hand planers and "planed" the cord on the backstroke... 🖐 ⚡⚡Thanks for the cool video. I like the idea.
I guess only you, lol.
Que gran idea...!!! 👍🏻👍🏻👍🏻
Thanks for watching sir.
Very nicely done and shown simple jig that saves a lot of time and money leavening wooden boards nice take care 😀👍
Thanks for watching sir.
Man, I was just trying to imagine a way to do this and you nailed it! But I think a router sled is much simpler and easier to adjust cut depth (I imagine), so I'll probably do that, but still awesome job.
Thanks for watching sir.
A router sled takes off way less material at a time.
There might be more of an adjustment with a router depth wise but I expect this method would provide a flatter finished product overall.
@@devonswindell9735 In my case that's a good thing. I tend to take too much off when I'm using the planer. I can't seem to ever get it right. Maybe I'll have more success with my planer. I keep gouging the wood at the ends. I really want to use my planer so I'll try this for sure.
If you make a rail system which is adjustable, using angled aluminum, for example, with multiple notched attachment points, you can adjust very well.
That is an awesome jig J! Great idea & nice work......... 👍😉😉👍
Thanks for watching sir.
sangat mengagumkan hasilnya. Sukses selalu.
Thanks for watching sir.
I like it! 🏆
Just yesterday I was telling a friend, "those things are only good for rough work like fitting a replacement window into an opening".
Thanks for watching sir.
Even withou the jig they're damn good, with a gentle touch you can get excellent results. But they make a horrible mess with dust collection.
Eine super Idee und ist wirklich simpel nachzubauen.👍🏼
BR Helmut #BeimBastler
Thanks for watching sir.
Brilliant work, dude! Fantastic! 😃
I just subscribed!
Stay safe there with your family! 🖖😊
Thanks for your kind comment sir.
Ur
Rhe
Inspiring your good idea ... thank you
Well, there’s definitely enough people on here pointing out how close you are to that blade (they’re right). Done careful, fingers are hard to reattach after they’ve gone through a saw...
However, I have one of these planers, and wondered how to get it to work better. I have a router too, but I’m going to try this, it’s a great set up!
Thanks for your kind advice sir. I'll be careful.
how unpredictable do you expect a table saw to behave with a sharp blade and cutting soft wood? I mean it's not a 100 years oak peace or anything. Simple pine is soft and nice to work with, saw cuts through it like a hot knife through the butter.
hola me ENCANTO saludos de Daniel Argentina
Thanks for watching sir.
Greetings from Korea.
What was the adhesive you used on the back of the plane? Seems to hold really well. Great idea
Silicon.
Thanks for watching sir.
Мастеру респект
Thanks for watching sir.
Very very clever and what a great idea. I enjoyed the video. 👍👽👏👏
Brilliant idea, I got to try and make this.
Thanks for watching sir.
Brilliant idea!!!
Thanks for watching sir.
GREAT JOB!!! Thanks
Thanks for watching sir.
A bit of setting up to do but after that you get a beautiful finish.Have you thought about putting a spiral blade on or are you happy with the straight blades.
The electric planer doesn't have spiral blade option.
Thanks for watching sir.