Thanks a lot for the oscilloscope and for the new firmware. Still, there is a question concerning time stamp of the saved files. All of them have the same date 22.03.2020. What about the possibility to improve this situation?
My screen went blank, and the screen no longer turns on. I can hear the unit click on, but for some reason the LCD screen is dead. It's only three months old. I tried different 5v 2a power supplies - no change.
Buyer Beware! This scope does not meet its bandwidth or sampling rate specs! Check out reviews on CZcams channels "learnelectronics" or "Kerry Wong" for more information. Spoiler alert: Instead of 1G Samples/sec, it samples at 200M Samples/sec, and instead of a bandwidth of 100Mhz, its bandwidth is about 30MHz.
Take an adjustable resistor of 10kohm. Now connect generator output wires to both ends of this resitor. At center contact of this resistor you get an adjustable output signal. Simple!
Olá, comprei um osciloscópio FNIRSI 1014D, e notei que numa ponta só medir uma bateria 9V só mede a tensão positiva, se eu inverter a polaridade da bateria, ele dá um pulo para baixo e não mede mais a tensão negativa, porque está invertido a polaridade na ponta. Se eu medir com a outra ponta, ocorre o contrário, mede polaridade da bateria do contrário e não mede invertendo. Caramba, que estranho. No meu osciloscópio analógico aqui, com a mesma ponta meço tanto tensão positiva quanto negativa. Aí não sei se é um defeito ou característica. O que será?
i would like to buy this scope as it has more for much less compared to others but one thing seems to be missing that actualy is on a cheaper tablet scope from FNIRSI that being the ability to self calibrate the probes to the scope I cannot see it on this scope i can get this for 150 euro and will have to pay 50 euros more for a hantek 100mhz with a signal generator So if anyone from FNIRSI can tell me where the self calibration function is ?, I will buy one.
I agree with Yusuf Oylum. It is rubbish, both software and the hardware design stink. Having reverse engineerd the 1013D and compared the two firmwares I can confidently say this about these scopes. And service is non existent. When I bought my 1013D it arrived with a defective touch panel. Trying to repair it resulted in a broken glass panel and FNIRSI did not aide in any way to resolve it. I did get most of my money back from the Aliexpress vendor I bought it from. To get it fixed I turned to reverse engineering the damn thing. Also have a 1014D which was donated to me, so also have insight knowledge on that one.
100 Mhz is bullshit and can measure up to 35 Mhz. Firmware has a lot of issues,bugs etc. You can not receive any mail from company. My both Fnirsi 1014D bricked somehow, does not pass Fnirsi logo. I do not recommend any of these products if company is Fnirsi. Put some money and buy Hantek or Owon.
@@fnirsi been nearly 2 months, device bricked after 2 days of use. I can not use my device that i paid for. Never ever gonna buy anything related to Fnirsi. I sent 2 e mails and no response for 5 weeks..
![[BRAND NEW] FNIRSI DSO-153 ⭐ Oscilloscope & Signal Generator](http://i.ytimg.com/vi/8_s7yX8SnX8/mqdefault.jpg)
1014D V3.0 firmware version (October 6, 2021):
www.mediafire.com/file/wdelwzj9hyhvt9e/1014D_V3.0_firmware_version_%2528October_6%252C_2021%2529.rar/file
FNIRSI-1014D Official Purchase Channel:www.aliexpress.com/item/1005002439042775.html
Got this in the mail this week. I really like it
My favorite thing in this video are the random screams in the background.
🐱👤
Can the amplitude of the generated signals be adjusted?
Do you have a version with a protocol analyzer?
Can you tell me how the 100mhz bandwith was derived, as advertised?
Thanks a lot for the oscilloscope and for the new firmware. Still, there is a question concerning time stamp of the saved files. All of them have the same date 22.03.2020. What about the possibility to improve this situation?
My screen went blank, and the screen no longer turns on. I can hear the unit click on, but for some reason the LCD screen is dead. It's only three months old. I tried different 5v 2a power supplies - no change.
Thats nice scope hope i have it
Is there some problems, from device to device
Does it have a EXT-Sync input ? and how about (the seldom but nevertheless still used ) Z-input ?
I don't think it has such functionalities.
You explain it so well. That's sarcasm.
Acabei de comprar por causa desse video.
THANKS
qual valor? gostou??? é bom???
@@Marcosautomec Querido amigo，As necessidades de cada pessoa são diferentes
Будет ли прошивка на русском ? Инструкция на русском? И где скачивать обновления прошивок ?
Will it be possible to update the firmware in the future, e.g. when bugs are discovered in it?
Hi，Dear friend ,YES，If there is a bug in the software, we will fix it and update it.
You can fix the problems by updating the new firmware
هل يقيس التيار ؟وماهي اقصى قيمة ؟
Buyer Beware! This scope does not meet its bandwidth or sampling rate specs! Check out reviews on CZcams channels "learnelectronics" or "Kerry Wong" for more information. Spoiler alert: Instead of 1G Samples/sec, it samples at 200M Samples/sec, and instead of a bandwidth of 100Mhz, its bandwidth is about 30MHz.
can i buy this on lazada or shopee in malaysia???
Hallo. Is it possible to reduce the amplitude of the generator signal?
No, it can't.
Comprei nos primeiros dias do lançamento estou esperando chegar
Hi，dear friend ，We are very grateful for your trust and support
@@fnirsi chegou o osciloscopio foi a pior compra q fiz !
@@alfredojarbasbarrosdacosta4926 o que houve?
@@alfredojarbasbarrosdacosta4926 oque foi , presta nao ?
I would like to see the features of your DPOX180H in this size.
There will be 300Mhz in the future.
If you like our equipment,
Welcome to follow our channel.
It available in sri lanka?
function generator amplitude can not adjust. How to solve the problem ?
Take an adjustable resistor of 10kohm. Now connect generator output wires to both ends of this resitor. At center contact of this resistor you get an adjustable output signal. Simple!
Olá, comprei um osciloscópio FNIRSI 1014D, e notei que numa ponta só medir uma bateria 9V só mede a tensão positiva, se eu inverter a polaridade da bateria, ele dá um pulo para baixo e não mede mais a tensão negativa, porque está invertido a polaridade na ponta. Se eu medir com a outra ponta, ocorre o contrário, mede polaridade da bateria do contrário e não mede invertendo. Caramba, que estranho. No meu osciloscópio analógico aqui, com a mesma ponta meço tanto tensão positiva quanto negativa. Aí não sei se é um defeito ou característica. O que será?
Olá, este foi um erro de montagem.
Neste caso vc vai ter que abrir o osciloscópio e medir e inverter dois fotoaclopadores, eles estão abaixo das blindagens.
Tem vídeos na internet sobre isso
Wow i love the simplicity of the interface!!! I love it! I hate my rigols one
Dear friend, thank you for your compliment,
The engineer has died laughing in the toilet🤣👍
@@fnirsi gui interface looks really good
@@fnirsi I think I will buy this to replace my Rigol. I agree Rigol interface is terrible.
@@nix324 no because it can not read more than 35 Mhz..
How is the 100mhz bandwith derived as advertised, because the scope's 3db bandwith is 30mhz.?
Sir how to chak signal
the probe is isolated or not?
Hi, Dear friend,
The problem has been solved.
The firmware version has been upgraded to V3.0 firmware version
no, at all
Хороший для домашнего использования. Но кажется видео ускоренное.
Привет, дорогой друг,
В целях экономии времени друзей ускоряйтесь в 1,5 раза
لو سمحت ممكن اعرف سعر الجهاز
i would like to buy this scope as it has more for much less compared to others but one thing seems to be missing that actualy is on a cheaper tablet scope from FNIRSI that being the ability to self calibrate the probes to the scope I cannot see it on this scope i can get this for 150 euro and will have to pay 50 euros more for a hantek 100mhz with a signal generator So if anyone from FNIRSI can tell me where the self calibration function is ?, I will buy one.
Hi，Dear friend ,
In the upper right corner of the panel,
The blue button "AUTO" is automatic adjustment
@@fnirsi Will it be available in India? If yes, then when?
@@GautamKumarGoswami Hi，dear friend ，India has distributors
Hello sir I am from India
I want to buy this oscilloscope
Please send some link from where I can buy it
on Amazon.
Hi sir,
Is this oscilloscope ok for Automotive diagnostics and repair ?....
Thanks.
Regards.
👍😎
Sweep gen include?????
What do you mean, friend?😅
@@fnirsi Does this oscilloscope have a sweep generator? Sorry for the english
@@fnirsi I do repairs on audio interfaces, I use the generator to check the response linearity after the repair
Vi comentários que ele não tem durabilidade.
Ufff hay mejores opciones la verdad por experiencia no te lo recomiendo
How mouh this one indan price
Hi，dear friend ，India has distributors
I agree with Yusuf Oylum. It is rubbish, both software and the hardware design stink. Having reverse engineerd the 1013D and compared the two firmwares I can confidently say this about these scopes. And service is non existent. When I bought my 1013D it arrived with a defective touch panel. Trying to repair it resulted in a broken glass panel and FNIRSI did not aide in any way to resolve it. I did get most of my money back from the Aliexpress vendor I bought it from. To get it fixed I turned to reverse engineering the damn thing. Also have a 1014D which was donated to me, so also have insight knowledge on that one.
Sir how to connect to pc
You can connect to PC with USB cable and enter into the menu then finding the option USB Export, only to share files
uow
ESSE APARELHO NÃO CUMPRE O QUE PROMETE.
😂 FENASI MARKA 😂😂😂😂😂
خوب که چی می خواهی دل ما را اب کنی
А Русский язык есть???
С виду красивый)))
Нам очень жаль, наш друг,
На данный момент доступны только китайский и английский языки.
@@fnirsi А как переключить с китайского на английский? У меня на китайском все, не могу найти.
@@alchoholocaustable Здравствуйте, дорогой друг, вам нужно только обновить прошивку.
@@alchoholocaustable www.mediafire.com/file/tfjugp8i3csfrzd/FNIRSI-1014D_Firmware_Update_Manual.docx/file
@@alchoholocaustable www.mediafire.com/file/ppeajlhbdm1szo4/FNIRSI-1014D_Product_Manual.pdf/file
www.aliexpress.com/item/1005002439042775.html，
Just started to go public,
The official store is opening an event，
PAGE NOT FOUND
100mhz please check and look
my dream is a world where silent movies are banned and those who have nothing to say are sent to siberia.
100 Mhz is bullshit and can measure up to 35 Mhz. Firmware has a lot of issues,bugs etc. You can not receive any mail from company. My both Fnirsi 1014D bricked somehow, does not pass Fnirsi logo. I do not recommend any of these products if company is Fnirsi. Put some money and buy Hantek or Owon.
Hi，Dear friend ,
What's wrong with your device?
@@fnirsi czcams.com/video/T7G6W0tPeOw/video.html
@@fnirsi been nearly 2 months, device bricked after 2 days of use. I can not use my device that i paid for. Never ever gonna buy anything related to Fnirsi. I sent 2 e mails and no response for 5 weeks..
@@yusufoylum7148 Dear friend, what's your email address?
@@yusufoylum7148 Don't worry,
I will help you solve the problem.