Hi guys, sorry for no response 🫣 it's a few years ago.. It was bad wiring.. all the electronics had to be checked and bad cables repaired. After this repair I also had problems with voltage regulator and battery... But after that It was finally okay 🙂
@@TwofierceTony i'm not completely sure. The sensor at the clutch casing delivers signal for speed (which is 0 in the video) but i do not rember 100% if RPM was also 0 once it occurred at my shiver
Grande Moto, mi dispiace dei tuoi problemi, all'inizio me la fatto anche a me, poi ho messo le tre mappe (la mia era uscita con una sola mappa) e il problema e' sparito. Guarda cosa ho combinato alla mia. Ciao! czcams.com/video/htwoanGTAfI/video.html
@@rrBiker_ Ciao, mi si e' spenta una volta, poi dopo 10 minuti ferma e' ripartita. Poi, il concessionario Aprilia mi ha istallato le tre mappe e non ho avuto piu' problemi. Dunque, non resta che dare gasss! Ciao!
Ciao rr Biker, ma no', la moto e' sempre andata bene. mamma Aprilia le moto le sa' fare. Poi capita la sfiga di beccare un'esemplare nato male, ma capita in qualsiasi azienda. Buona giornata.
@@raffaracing3772 eh guarda te l'ho chiesto appunto perché sulle vecchie shiver c'è stato un difetto di fabbrica nella distribuzione, con una vite e una boccola e hanno fatto una campagna di richiamo per questo motivo
Hi guys, sorry for no response 🫣 it's a few years ago.. It was bad wiring.. all the electronics had to be checked and bad cables repaired. After this repair I also had problems with voltage regulator and battery... But after that It was finally okay 🙂
Which wires were faulty?
I have the same problem, can you give more details please ?🙃
Well.... There's the name for it, SHIVER. I hope you fixed it and had no problem afterwards. Enjoy the ride, stay safe.
did you find the cause why it shuts off?
The wiring harness on those bikes are bad. Look for corrosion in the wiring. My dads Shiver had that problem.
Battery issue problably faulty same with mine until replaced
possibly an ignition problem
spedo shows 0 kmh - in my case there was a sensor in the clutch case which had bad connection.
That analog gauge is RPM..it stalled randomly while he was driving
@@TwofierceTony i'm not completely sure. The sensor at the clutch casing delivers signal for speed (which is 0 in the video) but i do not rember 100% if RPM was also 0 once it occurred at my shiver
Push start
Because italian :)
your bike broke down man. You should get a Gixxxer
Čo sa stalo?
'Co sa stalo?...Ma che lingua e'?
Grande Moto, mi dispiace dei tuoi problemi, all'inizio me la fatto anche a me, poi ho messo le tre mappe (la mia era uscita con una sola mappa) e il problema e' sparito. Guarda cosa ho combinato alla mia. Ciao! czcams.com/video/htwoanGTAfI/video.html
Ciao! Potresti dirmi che problema era?
@@rrBiker_ Ciao, mi si e' spenta una volta, poi dopo 10 minuti ferma e' ripartita.
Poi, il concessionario Aprilia mi ha istallato le tre mappe e non ho avuto piu' problemi.
Dunque, non resta che dare gasss!
Ciao!
@@raffaracing3772 ahhhhh roba di elettronica e basta insomma. Hai avuto problemi riguardo la distribuzione? Fatto campagne di richiamo?
Ciao rr Biker, ma no', la moto e' sempre andata bene. mamma Aprilia le moto le sa' fare. Poi capita la sfiga di beccare un'esemplare nato male, ma capita in qualsiasi azienda. Buona giornata.
@@raffaracing3772 eh guarda te l'ho chiesto appunto perché sulle vecchie shiver c'è stato un difetto di fabbrica nella distribuzione, con una vite e una boccola e hanno fatto una campagna di richiamo per questo motivo
u fill up with fuel😆
Bad connection....zly kontakt