How to Operate & set Parameter (Chipconveyor Inverter type)

1. Manual Operation by Inverter
(Machine Ready , Door close, does not matter mode)
2. How to set parameter
(navigate button, Up & down)
3. Manual operation by button
(Machine Ready , Door close, does not matter mode, middle position on inverter)
4. Auto operation by M-code
(M24/ M25 = Chip conveyor start / stop , M52/M53 = door close / open )
******* Standard Parameters *******
P-01 H 70.0 Maximum Frequency / Speed Limit
P-02 H 40.0 Minimum Frequency / Speed Limit
P-03 2.5 Acceleration Ramp Time
P-04 0.00 Deceleration Ramp Time
P-05 0 Stop Mode Select
P-06 0 Energy Optimiser
P-07 220 Motor Rated Voltage
P-08 A 0.8 Motor Rated Current
P-09 H 60 Motor Rated Frequency
P-10 0 Motor Rated Speed
P-11 3.0 Torque Boost
P-12 0 Primary Command Source
P-13 0 Industrial / Fan-Pump Control Mode
P-14 100 (201) Extended Menu Access Code
******* Extended Parameters *******
P-15 7 Digital Inputs Function Select
P-16 In-Pot Analog Input 1 Format
P-17 8 Effective Switching Frequency
P-18 1 User Relay Output Function Select
P-19 100.0 Relay Threshold Level
P-20 H 5.0 Preset / Jog Frequency / Speed 1
P-21 H 25.0 Preset / Jog Frequency / Speed 2
P-22 H 40.0 Preset / Jog Frequency / Speed 3
P-23 H 60.0 Preset / Jog Frequency / Speed 4
P-24 0.00 2nd Ramp Time (Fast Stop)
P-25 8 Analog Output Function Select
P-26 H 0.0 Skip Frequency Hysteresis Band
P-27 H 0.0 Skip Frequency Centre Point
P-28 0 V/F Characteristic Adjustment Voltage
P-29 H 0.0 V/F Characteristic Adjustment Frequency
P-30 EdgE-r Terminal Mode Restart Function
n.c Fire Mode Input Logic
OFF Fire Mode Input Latch
P-31 1 Keypad / Modbus Mode Restart Function
P-32 0.0 DC Injection Duration
1 DC Injection Braking Mode
P-33 0 Spin Start Enable
P-34 0 Brake Chopper Enable
P-35 100.0 Analog Input 1 Scaling
P-36 Adr 1 Drive Address
115.2 Modbus / CANbus baudrate
t 3000 Communications Trip Delay
P-37 101 Extended Menu Access Code Definition
P-38 0 Parameter Access Lock
P-39 0.0 Analog Input 1 Offset
P-40 0.000 Display Speed Scaling Factor
1 Display Scaling Source
P-41 1.0 User PI Proportional Gain
P-42 1.0 User PI Integral Time Constant
P-43 0 User PI Operating Mode
P-44 0 User PI Reference Select
P-45 0.0 User PI Digital Reference (Setpoint)
P-46 0 User PI Feedback Select
P-47 U 0-10 Analog Input 2 Format
P-48 0 'Standby' Activation Delay Time
P-49 5.0 PI Wake Up Error Level
P-50 0.0 User Relay Output Hysteresis
******* Advanced Parameters *******
P-51 0 Motor Control Mode
P-52 1 Motor Parameter Auto-tune (1로 설정 Autoset후 0으로 자동 변경)
P-53 50.0 Vector Mode Speed Controller Gain
P-54 150 Maximum Current Limit
P-55 Autoset Motor Stator Resistance
P-56 380 Motor Stator d-axis Inductance (Lsd)
P-57 38 Motor Stator q-axis Inductance (Lsq)
P-58 H 0.0 DC Injection Speed
P-59 20.0 DC Injection Current
P-60 r 1 Thermal Overload Retention
o 0 Thermal Overload Management
P-61 0 Ethernet Service Option
P-62 0 Ethernet Service Timeout
P-63 0 Modbus Mode Selection
P-64 2 IP66 DI1 Source
P-65 0 IP66 DI2 Source