First Engine Rebuild Attempt Fails - Now What?
Vložit
- čas přidán 15. 11. 2022
- First ever attempt at rebuilding an engine fails. see where I went wrong and what the next step is.
Go Tell Clint from C&C Equipment thanks and be sure to subscribe to his channel!
/ @c_cequipment
Here is the progress playlist for this backhoe!
• Ford 555 Backhoe
Be sure to follow our other social media to see more progress photos of our projects.
Facebook:
/ captainkleeman
Instagram:
/ con. .
TikTok:
vm.tiktok.com/TTPdrXq8Na/
DISCLAIMER'. this is not a how to video and I am not responsible for any actions you take on your equipment or property
Abandoned Backhoe Hasn't Run for Years - Will it Start?
#captainkleeman
#enginerebuild
#fail - Zábava
Hi Mike, being a former mechanic, I immediately knew what you meant by the “foreshadowing” reference to using plasti-gauge and I am sorry that you made this discovery the hard way. Fortunately, you didn’t make things worse - and you already have the right idea in reinstalling the old bearings. I just hope that you numbered them and kept them in the correct order because that’s what they teach you in school and yes, I have been an instructor of such classes. I too have rebuilt engines lying on the ground - but not on frozen ground - that’s where I draw the line these days; at 67 it’s just not worth it anymore - plus I got money to pay people to do that for me now. I hope it works out because after so much work you most certainly deserve a win. Someday soon we will all see the refreshed motor running and you bursting old hoses left and right - and pressure-washing away the rust, mold and dirt.
Bring on the hoses! I'm ready for that step lol
I have to admit I was on the edge of my seat knowing something bad was coming. Glad it wasn't catastrophic and I'm sure you'll get it sorted out. Thanks as always for sharing your journey, your attitude is an inspiration.
love the effort you put into the channel but recently the audio is off set from the video a bit distracting
Ive seen several comments on this issue lately. Not sure why that is so important to people. He is building things, wrenching on old junk, (even in the cold and snow), and providing great content, in the process. It might help to focus on what he is doing with his hands. It could be a hardware issue or a software issue. Either way a lot of content providers have synchronization problems with their audio.
Full disclosure...I am not being snarky. Just trying to help.
@@jdelbrid Thank you you did a good job explaining. God bless
I found the hammering to be fun during the first piston. The timing had the rebound with the main strike. It kept my brain thinking. Still not that big of a problem. Captain thanks for bringing us on the journey.
Sound is off but I don't mind. Sound of the hammer made me 😃 .. love a little lightning and thunder action.. keep up the entertainment captain
@@jdelbrid 💪
Boy can I relate to your situation. Been there, done that. I like how you keep such a positive attitude. I usually end up using more than one word that doesn't appear in the dictionary. I keep doing it though and really appreciate you showing me how I should handle it. I've gotta believe that the backhoe will serve you for many years to come.
I am not considering it a fail. You are making progress, Have a good mentor to lean on, and lots of support. Despite the trouble you are having, You really do make it look easy.
Mike don’t beat yourself up, you did it and will learn tremendously from this. Keep up the great videos!!!! Thanks and just keep doing.
Yes I appreciate his videos is humbleness doing it on his own and getting away from people. Working with the public can be stressful and this give him peace even When things don’t go right.
As they say on another channel I watch. "we do it right because we do it twice". Bummer about the extra work but I suspect you will never make that mistake again. Thanks for posting. Really enjoy watching.
Lol I like that
Capt, for not being a mechanic and working on a tight budget, even with this slight setback, you're doing a heck of a job😺
Thanks for sharing👍👍👍👍👍😺🤗🐺
Thanks Glenn
9:38 ish - when hammering there is a loud bang before the hit then a faint bang when you hit - not a problem as it was quite melodical 😊
loving the backhoe series you are doing a fantastic job! every step is a learning experience for me watching you do it! keeping it affordable and bring what you rung approach is awsome!
EXACTLY how I learned...IN an engine rebuild course at a Florida college!!!
First day:
Professor says go pull the engine out of that Grand Marquis parked outside and put it on this table.
Zero actual engine removal instruction. His style of teaching...I learned more in that series of courses than any other teaching style throughout a lifetime--this far.
Dive in with a strong will to survive: you will become a swimmer!
Love it
Cap’n, my guess is, it’s the rod bearings that are binding… “Why?”, you ask…
Well, that’s what I screwed up in my first overhaul!!
Unlike you, I didn’t stop when the starter wouldn’t turn the engine over. No siree! At 18yrs of age, I wasn’t patient or experienced enough to have such horse sense.
Instead, I grabbed a tire tool and began prying on the fly wheel. After it turned a little bit, I hit the starter again. Nope! It needed more tire tool. An hour later, I finally got the starter to feebly turn the engine over a couple of revs. I was certainly making progress.
That got my hopes up. So, I went to dinner with anticipation of a fresh start the next morning.
I called my mechanic buddy and bragged about my progress… until, he said, “I hope you didn’t ruin the crank shaft.”
The next afternoon he came out to the farm and we tore the bottom of the engine apart again… the lack of torque wrench use and putting the bearings in without lube caught up with me.
My enthusiasm and pride fell into an abyss… the scored crank shaft and chewed up fly wheel sent my empty wallet down there too!
So, I’ll be waiting in anticipation for the next installment to see just what you find… regardless of the unknown date of its posting!
The comedy on this channel is just top notch, thanks captain!
We are all there with you Mike, just waiting to hear that 3 cylinder come to life. Ok, we might not be "there" with you, but sitting in our Lazy Boys, we are all rooting for you!!!!!! Keep up the great work, you got this!!
I would always dip my pistons into a small bowl of oil to load up the rings with oil before sliding them in. Engine pre-lube on the bearings or at least a little grease on them will make a work of difference. Tighten down your bearings and rotate the bottom assembly before you install the head will tell you if there is a problem. First engine I ever rebuilt on my own the first time I completely forgot to install a set of rings on a piston. What a pain in the ass mistake that was to pull the head and pull a piston all the way back out again! We are all human and learn from the journeys we take. Thanks for bringing us along on yours!
Years ago, I watched as my neighbor's kid did a similar in chassis rebuild of an old AUDI. Occasionally, he would hail me for advice and/or assistance. Having zero confidence that it would ever run again, I was astonished when it fired up on the very first crank. Perhaps all you really need is a good neighbor and some better luck. You'll get it. I've seen worse.
Sorry about the set back man. It happens. I'd blame it on the wild temperature swings in the shop. Lol. Keep pushing brother.
The thermostat is struggling
Wild West it is ! and i love it ! good job, as some say, the first time you do something you are going to school, second time you are in known territory and is easier .
Thanks Charlie
I sure love how you deal with the possibility of a negative comment before one can be made!!👌👌
We learn - we grow.
And we get to grow along with you - thanks Mike!
Hey thanks for watching
If you could reach it, you can get much quicker verification that things will move if you would have turned the crank externally with a socket while the head was still off and make sure everything turned. Try it on Round 2.
Editing and proofing department needs a reprimand, no day off this week, lol. Another great vid, thanx for sharing.
Captain it sounds like the sound is not in sync. :) Thank you and have a great week. PS I live above the 49 parallel in the Pacific and we do not have snow, weirdness again. :)
Sir , it needed a battery originally , that was all. Also , I have had milky trans / hydro fluid freeze ,that will create a no crank situation , I had to push a clutch in on my ford 4500 tractor , to get it too crank / start. These experiences are hard taught , you don't forget them , after years of making mistakes like that ,(or watching someone else make them) you become a run of the mill mechanic. No crow to eat here , you knowledge level is through the roof , compared to when you started . In hindsight , it's best to work in a shop environment for years , to pick up some basic knowledge . Google and CZcams make bad mechanics, overloads people with confidence. Thanks for being honest , your a stand up guy. I am subscribed . Thanks for good , honest content.
Mike don't be so hard on yourself we've all been in your shoes little patience a little more studying and you'll have that thing up running and humming God bless
As someone who has worked on everything from tricycles to bulldozers and mini bikes to large prime movers if there is one tip I can give a person doing engine work is if the engine is locked up when disassembling it put a bar on it and every time you loosen/remove something (engine component) see if it will move (try to bar over the engine) additionally when assembling an engine every time you install a part bar over the engine to make sure that still bars over and while when you install a pistons you will get some more drag the engine should/will still rotate smoothly. This one tip can help diagnose what the trouble is and will certainly stop you from having continuing when a problem develops.
I enjoy your humour and ability to laugh at things even when they don't go right. Persistence is key. Have fun. See you next video.
Thank you!
The magic hammer with sound effects/pre hit noise is really interesting. Seems like something for the merch store as nobody else seems to have them.
Even though I'm an old lady who always watches your videos, I usually never understand what you're doing. LOL However, your videos are always entertaining, and informative, and please know that I am always here cheering you on!! You will get the results you need. It may take a try or two, but I have complete faith in you, and your determination. Best of luck to you, Captain!!
Lol thanks for the support!
Always rotate the engine after tossing pistons and rods in......sheesh! LOL This is how you learn. Its all good!
Glad to see others have the same issue with the sound shift, I thought maybe it was because we watch on our tv.
Bud, don't get down! I hope it is something simple! I can see the stress and wanting everything to be perfect! Just step back and take a deep breath and become the captain Kleeman that we all know and everything will fall into place for you! I love the happy go lucky BUD
When I finally stopped laughing I actually felt bad for you, but then I just started laughing again, thanks Mike. Cheers from down under.
Back in the day starter torque spec was good and tight..yep that will do'er.🤣🤣🤣
😂😂
Ring gap wouldn't stop the engine turning over, it would damage the bores after a while. Did you set the valve clearance?, did the engine turn over by hand?.
The big end bearings are coming off anyway, so check the ring gap while everything is easy to get at. Tighten the ring compressor as much as possible before knocking the pistons in, and hold the compressor down on the block while tapping in the pistons. Good luck 👍 with your project. Great vids.👌👌
I use an oil stone/wet stone instead of sanding paper. Solid off its own.
Its better to put the rings in the liner and check the gap. Nowadays they are fitting well. On older parts you needed to make the gap clearance. These cranckshaft bearings have a thin layer of material. Thats why plastigauge is used instead of the old leadwire. But better: put the rod/cap toghetter, torque them and then check if you can move them fore/afterward by hand or screwdriver. If they slide easily 1/25 or so of an inch youre good.
Oil or grease will hold a gasket as well.
Sorry for you but youre on the right track. Rethinking wat you did and where it took a sidestep. Hats off for you from a marine engineer!
Thank you sir!
You got this buddy !! I am very impressed with your fortitude and strength to concur your projects !! Tomorrow is always a new day !
Thanks mike
You are still my Hero Captain Mike! Press on Sir, we have your back.
A hard lesson. Good video keep trying you will get it.
I have a lot of respect for you, Mike! You make mistakes, like everyone else does, but you persevere through it. Keep on going!
Hi I know nothing about engine work, and so am hot going to say you should have done this or should have done that. But I will say don’t let the knockers & knocks stop you, it is easy when you are watching a screen in the warm. And the man who never did anything wrong has never done anything. All the best keep going. 👍🐝😊
"Here we see the native 555, desolate and alone.....waiting for that one cowboy that can tame 'er and make the west less wild" lol love the commentary!!
I laughed when you said, "you're the one who hit the play button."
Really liked watching you doing the engine rebuild. Thanks for the videos.
Good job up loading when it is convenient for you. Keep up the good work
One of the best lines I've heard in awhile "well you pressed the play button "
😂
Your doing fine. Every mistake you make is a learning opportunity and will be burnt into your brain helping you on future repairs. Here's a old school gasket holding tip : Tie the gasket through the bolt holes to the oil pan with some sewing thread from the Mrs. Bolt the pan to the block loosely, snip the threads, pull them out and tighten your bolts. No fancy spray-tack required. Best of luck.............
Always a learning curve. Great attitude and video. Thanks
Watching you do these things have Inspired me to work on my stuff starting with new brake pads on my car . Never done anything like that before but how Hurd can it be 😮
your right lots of armchair mechanics on here one thing as a millwright for 28 years we use to use STP oil treatment to put gearboxes and motors together great video look forward to the next
Makes since, thanks for watching
Gotta love the heated shop! Your attitude is why I keep coming back for more videos.
You my friend are a hoot.!!!
At least you can say you made this grammas day better.
This journey is definitely getting interesting thanks for taking us along so we can learn together. Stay safe
As allways you make it a real joy to watch..even when it doesn't going along as planned.
lol - I was muttering at the screen - "don't you need to clock those rings?". Then you stopped and explained the gaps need to be rotated.
Love you videos! Don't let it get you down! You got this. :)
💪
So glad You ran the ball hone some more. I was worried it wasn't enough when looking at the pics. Fingers crossed hoping for the best, can't wait to hear it run.
You will get it going , I have faith in you, just keep plugging away and keep getting advice from Clint. 😁👍
I dig your patient and happy-going demeanour.
Captain you will sort it out. Nothing runs the way you want it. That's what I like about you. Sit back have a cuppa of tea, and you will work it out. Keep the vid's coming Captain.
That was magical lol,you're doing great keep it going
Thanks Troy
Great work love your attitude to life wish more you tubers were like you not worrying about the haters l know you will sort the backhoe out looking forward to the next episode 👍
❤️ love your tractor, new or experienced, we all go through the same thing. I learn and am inspired by you and admire you for lots of reasons. It's about vision and how far we're willing to challenge ourselves. The greater the challenge, the greater the victory. Great work, great vision, great pushing yourself, great video. Have a blessed day.
I feel your pain! Years ago when I was 16 I was working on my first car, a 1963 Ford Falcon that needed new rings and one new piston. When getting the parts at the Ford dealer, I decided to replace the rod bearings. The parts guy asked me if I wanted standard or 10/1000 oversized. Thinking quickly I said oversized since the engine was obviously very worn. Well, you know what happened when I tried to start it….NOTHING! 😂
Painful, but a lesson I’ll never forget.
👍😎
😂 lessons learned! 💪
63 Falcon is one of my favorite cars 🤗. I had a 63 n put in a 260 V8 out of a 64 sprint Falcon engine in it and a 71 Mustang f/r suspensions and disk breaks and 50 series tires all the way around. 🤔 the 2 speed automatic (slush-box) was garbage it needed a good 4 speed.
I did hit the Play button - and I'm not mad about anything you do! Mind you, that's probably because I wouldn't know where to start. Another good one Captain, and with your 'can-do' attitude you'll get it running in the end - I have faith!
You will get it Captain... We have faith in your abilities!,👌👌
Thanks rich
It is fun to watch you.
Looks like your have fun.
I hope your having fun.
Definitely
Warm pistons up in hot water will make fitting gudgeon pins easy, ring gaps average is .004" for every inch of bore, stagger ring gaps. Built lots of those three cylinder Fords Good video
Thanks James
Nice rebuilt video have a great job of the big runs right when you get done putting all this work in it all right have a good one buddy 💯💯💯💯💯
Thank you
👍🏻👍🏻 because one is never enough. Love the positive attitude all the time. Yes, there’s steps you should’ve taken but for whatever reasons you didn’t. Don’t beat yourself up over it. You’ve learnt more and you won’t make those mistakes again. It’s a joy to watch you learn and grow through your videos. Keep smiling and laughing as it’ll all payoff when you’re done.
The Canadian tork specks are tight as it will go and one full turn
Lol
Mike you know what they say if at first you don't succeed try try again, and after watching you for a few years i have no doubt we will be seeing the 555 on the yacht build 👍👍👌
And this too will pass. Keep the faith brother. Stay safe, give the family my best.
Captain, if this is your first major engine rebuild.
You did a goid job.
Murphy has a tendence to show up with his Gremlin gang at the worse moments.
I'm sure you'll find what the issue is.
Next time feel free to get liberal with pre-oiling all parts.
There is a special oil for re-assembly of engines.
Did you adjust the valves after to torquef down the head or did I miss that part ?
Install the rod caps bearings in the correct orientaion ?
Ooh well, I'm sure you'll figure it out and us subs can breath a sigh of relief.
2 things that might make it easier next time you need to put new pistons in is get a container you can heat water in that the piston will fit in. Warn it up not quit to boil. You can also cool the ristpins in a freezer. Doing truck engines I have found heating the piston works well. I must say you have done alot of reaserch to make it work. Good job.
Mike, you are doing great. I can't get over how patient you are.
Thanks Roy
Captain you’ll figure it out! My best wishes to you and your family! Thanks for sharing! Kevin
Thanks Kevin
Keep after it Mike! Love what you are doing.
Thanks Kevin
You have the luxury of time Mike ,so if I were you I'd chalk it up to experience and keep on pushing straight ahead !
Stay tuned for 'Backhoes of the Wild West' with Captain Kleeman!
Crow! Mmmm nice. 😁Great vid. It will work.👍
Glad you do what you feel is the correct way!
Thanks for sharing your thoughts, ideas, adventures and videos. Have to admit I was really hopeful for some smoke but reserved since your on screen commentary hinted not all was well. Really like that you have a relaxed perspective and taking it as an adventure into engine repair and not a personal commentary of your abilities. As it’s said, if you never make any mistakes you will never learn how things are done, your just lucky. Looking forward to seeing the upcoming videos. Wishing you and your family the best.
Thanks tom!
Is it just me or is the sound and video not synced right? The last couple videos I have watched here have been the same way for me.
Mike I love watching your videos. I hope you continue to enjoy making them and posting them so I can continue watching. I love this series so far. Thanks for your hard work!
Some days I hate the internet but what a wealth of information that 20 years ago would be near impossible to obtain! Hoping for a great ending for this project! Didn't expect the ending we got but you will persevere!
Mike I love your attitude towards everything, the only way to learn is to try and fail. Failure is not a bad thing unless you quit then its all for nothing. Keep up the great attitude and content.
Thanks Brian
Mike I just live your attitude and way of teaching yourself 😊 your doing fine yes it’s frustrating to re do some things but it’s sometimes the best way to learn and remember for next time ! Also love the way your able to ignore the negative comments with humour too ! And who cares when you upload it’s just nice that your kind enough to do so ! Keep up all the good work and hope you and the family are well !
These ring compressor tools are great the first few engines I rebuilt my mates and I used rags and hose clamps
Good Afternoon Captain!!
Hello from North Mississippi. It is a pleasure to watch you tackle these projects.
Your shop sure has a strange echo. It was almost as if the sound came before the hammer blow.
Keep safe and God Bless!!
Wats up Capt K!!!!! I wouldn't worry about the criticism. You are the Capt and you do what you want!!! Great video as always!!! 😎💪👍
Thank you!
It's a good thing you check it before you put the head back on.
good to see you making progress.
Captain you were also supposed to check the ring gap. God bless
As the great Dory says, "just keep swimming". Great work so far, can't wait to see it running soon
That's right!
Keep it up Captain 👍You'll get it, and just think when your done you can dig a hole 🕳 and bury whatever caused it😊 Awesome Content 👌
😂😂
Right side of the block right where the block bolts to the front support is where the date code is.
Your doing great young man. I do like the room you have to move around in your shop, and the HVAC system, although some what uncontrollable at times, is the best in the business. Stay the course, you’re going to win, I just know it, thanks for the update sir, those mistakes are just negative learning experiences, myself, it sometimes seems to be the only way I learn.
Definitely a roomy shop lol
When you take the pistons out again and remove the bearings use some emery cloth and polish the end of the rod where the bearings sits. Also polish the rod cap. There will be a minute amount of contaminants that can affect the bearing fit to the crankshaft.
Don't feel bad, I just re-installed the professionally rebuilt "equipment control valve" on the old ranch dozer. Third "re-install" for the valve, first "professionally rebuilt." Didn't look that difficult to rebuild the first two times when I did it. Pro tip: The professional rebuild at the machine shop cost about $175 the parts kits I bought were about $60 each. Math. It is not my strong point.
Thanks for the video!
We've had days like that. Your doing great, keep at it and you'll have a nice machine when you're done.
Thanks Scott