How to program VIN after ECU swap.
Vložit
- čas přidán 11. 09. 2024
- In this video I show you how to program a vin in the Toyota after ecu swap if you need to program the immo security information watch my other video on how you can do that without a scanner . ecu swap after bad trany shifting, no shift transmission won't drive.
Does your scanner only write the VIN to a new/refurbished ECU, or does this also work on a used one pulled from a junkyard?
This video is for those with advanced knowledge because I haven't a clue about most of the technological terms used. They are not explained for those with less knowledge, so the video is no use to me in my efforts to see if I can fit a replacement ECU myself.
You Probably don’t need to be messing with it if you don’t understand pal
Short answer is no, need a fancy tech tool to talk to the computers.
My connector scanner has only 5 cables or pins and # 13 is empty what can I do in this case?
Nice job man. I wonder if I can rewrite the vin number for my fj Cruiser so that I can change the vehicle specs. Here in Libya we import usa toyotas with usa specs. Ihave heard about programming ECM for ignoring trouble codes those come because of CAT issues. Any ideas?
You can do that, it will be coding and some tuning so you would need the correct hardware (tools) and software
Hi can you tell me what scan tool do I need to do the VIN swap.
The high- end Launch scanner can write the Vin and most Snap On Scan Tools have the capability.
@@davidhall3747 can you re-write it thru the obd2 with diagnostic tool ? Because the video shows how to do it , but when the module is not connected with the car . Thanks! I am using thinkdiag
@@LoshiqBg I found out it depends on the Year, Make, & Model of the Car. You might need a J2534 Passthrough Device.
I successfully Cloned a 2001 Ford Expedition PCM, made Keys, but could not write the Vin. The PCM I Cloned to still has the VIN number from the Donor vehicle. My friend at the Ford Dealer will Write the correct Vin for me. I used a Snap On Verus Pro to Swap the PCM.
Hi does this work on a 2004 Volvo V70 ? I'm trying to use another Ecu that is been tune on my wagon any advice I greatly appreciated thanks
The scan tool used is it a fancy scanner same as obd2 scan tool?
It's an upper end scan tool Snap-On Solus Pro it looks like
It's fancy.
Do you know if a 2002 kia Rio 4 cyl auto with a separate engine and trans module would need the vin reprogramed after a used engine pcm swap ?
Good job, I replaced the original engine of my acura TL 2.5
With one of a junkyard, the VIN is not the same, where may I find
The VIN No of this new engine in my car to program the new computer.
Thanks if you can help. Ed
The vin # for Honda/Acura engines is a green tag on top of the oil pan facing the fire wall
Iv never seen the vin function on any snap on scanner where did you get that
maxisys pro got it
@@sky89line the price is waaaay higher on the maxisys
@@Moe_510. How in world do these companies advertise plug and play PCM’s when they don’t even have your car? I gave them my VIN #, it’s a 1996 model without PATS system. Do you think the new PCM will plug in and work in my car without using a scan tool?
Pats is the exception. They lied.
good informative video.....can you write VIN on a swapped ECU for 2001 Mercedes c240 (car runs and drive however, can't pass the inspection like you said coz the vehicle VIN is different from that ECU!).
Please reply asap....Many Thanks!
You need a Scanner capable of writing the actual Vin to the new/ used PCM. He is using a Snap-on scanner in this video with the capability.
Hi i have a toyota hilux sr5 5vzfe engine. I ordered an ecu with exact model. I heard it was plug and play?
what version number is the software that you are running on the snap-on ? have the same tool does not show the same info on screen . could you point me in the right direction ? thanks .
Bro you cant reprogram a ecu with this scanner
I think if you short out the ecu, the scanner will then be able to read or write. He mentions it in the beginning of the video. Ill try with my older snap on.
@@scottmiller4889 ever end up giving that a go?
How do I swap vin I have 05 ranger and bought a parts truck I want to use but have a donor that I'd like use the vin from it's a regular xl model no key chip do I just reprogram the ecu using the other vin ?
What other scan tools can Read / Write VIN? Something LESS EXPENSIVE maybe...
Nothing cheap will write vin autel can but it’s cheapest option is 1k
Hi I did have a question is this the same for swapping out 2006 Scion xB ECU ?
What did it end up being for you? Currently dealing the same with a 2005 xB
Hey how’s it going I have 13 Taurus ecu fried got a new at junkyard wrote turn on because pats and rewrite vin need a lil more onsite please
Love
Do you need the vin from the car you get the ecu from
No
Hy thanks for your time.
How come you didn't married the key to the ECU?
im having a difficulty with immo here with a new ecu replaced ford edge 2007.
Vehicle want stard what to do?
You need to be granted access to the Car's security system and need a minimum of two keys to program new keys. Otherwise you need to take your car to the Dealership.
Can I use a used ecu 2011 camaro shop says mime is bad and is causing car not to start
I need to replace a ecu on my 2010 Camry. I have ecu from another Camry but it won’t start without reprogramming. I can scanner Launch x431 pro mini
Hi there can I swp the ecu programming 2010 vw cc 2.0t
R you rewriting car u r workin on vins into usedTCM.
Do I need a snap on I have Autel but don’t see vin read write option. Can you point me to a scanner that allows me to do this??
I read the Launch Torque has the capability. The Launch x 431 Pro does all the programming except it has no Vin Write Capability. Unfortunately I have to use the Snap- On Verus Pro to write the Vin on a Ford PCM Swap.
I have an audi a3 with a touran computer box, the car runs but certain things arent working, if I do this vin change on my computer box, will it change the computer box to my correct model of audi a3 and make lead to everything working properly.
Changing the Vin only does nothing for Engine performance. Your cars PCM needs to be reflashed with the latest Configuration files from the manufacturer.
what do I need to flash my new ecu with the correct vin on my 2014 Nissan Altima? I have old ecu tcu bcm etc and new replacements for it including fob
Factory scan tool and lock smith id
None of this works.
U can do it without tool
I wish others automakers allow that too
I have an 08 jeep commander... it blew a rod threw the block so I'm swapping it out with an 06 commander motor same size engine .. I believe the egr valve is diffrent so the guy I bought the motor from gave me the ecu to that motor would it work if I rewrite the vin?
It can be programmed properly if the PCM part numbers are identical.
This is done all the time by experienced Automotive Technicians/ Engineers.
Can it work for 04 Honda Accord ex 4 cylinder
Which model number is this tool please? The 909 or 808?
Does this also apply to the TCU ( Transmission Control Unit) for VW. On my 2000 VW New Bettle 1.8t, I got error code 18034 (POWERTRAIN DATA BUS, MISSING MESSAGE FROM TCU). I found a used TCU with matching numbers. would it be plug and play?
No.
I need to program the used ECU I bought for my 2015 Honda Accord with a 2.4. How do I buy the device to plug into my obd?
Hey, did you figure out an answer for this or how to program it any other way? I’m trying to figure it out for myself lol
Just to reprogram a new ecu I'll need a scan tool ?
or a friend with one...
yes ecu needs vin number for key to work key has a chip
Yes. Use factory. Aftermarket is junk.
Hi i have replaced the ECM do i have to reprogramming the ECU with VIN i got error called service theft deterrent system Thaoe 2009 , is there's any way without the scanner can reprogram
Iii II iooiooiiooiooouoiiiououo i iooioiioioo II o.o ouoioooioiiiiiiiiiiiiiioiiiiiiiiiooii out Philipp
All you have to do is reprogram vin and theft- 10 minute relearn
@@cogunlover5550 hi i have nissan micra 2002 ecu fault i buy same part number but car not stat need program ask for pin i dont have
Does this work for a bmw 328i?
I have a 2001 s10 ZR2 and I want to swap the ECU from my 2002 s10 (numbers matching computer) if I swap it won't start. will doing this with my Solus pro allow it to start or do I need the dealer to flash the computer?
czcams.com/video/S4hb_yeMYpY/video.html
@@vehix411 do I have to program the VIN to the other ECM though? Or can I just swap from one s10 to the other then do the sequence from the video and it will work?
Hey I have a ecu off of a 2012 fiat 500 auto how can I reprogram to put in a fiat 500 2013 manual
Trying to figure out this same issue with my car. I have a 2003 BMW 330Ci ecu, and motor installed in a 2002 330i. Wondering if I need to remove the ecu from the 2003, and then reinstall to the other car.
Where do I find that program for an E46 2004
Can you show me how to change the vin on the computer on my Silverado I replace the computer but vin don’t match
How did you do it?
Do you know if an ECU can be swapped along with UCH and keys without need for programming?
You can’t, plus you’ll want the correct vin and known modules to be programmed otherwise you’ll have issues
@@weldingjunkie where is the VIN stored?
Dopamine Ht its stored in the ECM (ECU) and TCM and most of the other modules. You can rewrite vin without full programming by doing a Vin swap or write
@@weldingjunkie If it's in ECM why would it need reprogramme. What exactly would it need programming to? Uch and key are the same as old vehicle that I took ecu from. They sell kits on ebay for this particular van. It's just uch key(fob) and ecu
How in world do these companies advertise a plug and play PCU if they don’t have your car? Is that possible to do on a 1996 model without PATS?
No. There is no such thing as Plug & Play for the Ford PATS Security system. Your cars PCM needs to programmed onsite or at the Dealership.
Can I use this tool to just change my Vin number for some reason my ecu is showing me a different number from my car car title and dashboard
Yes, if you have a high- end scanner like the one shown in this video.
@@davidhall3747 ah thanks but I got.rid of this car 😭
@@LEFT4eV3r NP
I need your help.
how to program a new ECU to Golf 6 CDI
So I’m curious , I got my bmw engine swapped (2009 328 xi 6 speed ) they just put the engine in , and the car didn’t start . Can this be why?
It's possible. Plug in a cheap code reader and see what Vin pops up.
Would I need the jbox or does the pro do it stand alone?
You don't need a J2534 Box to swap PCM's. To Flash yes, for PCM swap, no.
What is the model of your scan tool?
Looks like a Solus Pro Snap-On
I got a question
How does your ecu know that's its in another car. Even if it's the same 2 cars. How does it know?
each car has vin number deferent then others
Ino each car has different vin lol. But how would it no. Example u put the ecu and imo and bcm from a lancer into a next lancer. How does the ecu no its a different lancer its not like the body of the car as a plug or smt
@@chriiss6936 a chip in the cluster with vin as well. if that and ecu dont match youll have problems
@@andrewkubas4143 does mitsubishi has that chip in the cluster ?
Hi can I use any scanner I need to do it for a Subaru Tribeca
No, not all Scanners are Bi- directional.
Hi, i have a 2006 lexus is250 , I have changed the engine to a gs300 3grfse engine, it seems to run fine on the is 250 ecu but I thought i would swap in the gs300 ecu.
I done the 30min ecu reset/pair but it wont start the car.
I am now swapping back to the 250 ecu as I pressume there is a conflict somewhere.
Do I have to re - pair my original ecu to the car ?
Thanks
my ecu doesn't have immobelizer
but my car starts....
Hi mate if ecu same part number I just need program immobiliser?? Ople 1.6. Thanks
Where are you located
Will this tool work for rewriting a vin on a 2008 forester??
did you try it ?
Do someone know where I can get my 2003 Isuzu rodeo pcm flash
Any different scanner tool beside snap on can re write VIN number?
Yes many do this. Xtool does way more for a lot less $$
Launch Torque has the capability.
I replaced my ecu on my 2007 corolla. I did the battery disconnect and the 30min paper clip reprogramming but it won't start. Won't even crank. Suggestions?
immobiliser ??
How do I fix? My car starts if I jump it though. Could ECU drain the battery?
Your battery is junk
@@bryanmccauley7913 What was your solution for this?
How do Cadillacs do with vin code rewrite I have a 2005 CTS I want to use the ECM from a 2007 CTS The service number on the ECM is the same I have an Ethos Pro Scan Tool
Easily. You guy a gm factory scan tool then pay 800 a year for access. Do them all the time
Did you get this figured out because I'm in the same situation
Will this work with volvos????
The Solus Pro Scan tool he is using is now obsolete. It depends on what year your car is. If your car is too new, you won't be granted security access to program the minimum of Two Keys requirement.
Does ECU shap change the vin number
It depends on the year, make, & model of the Car.
I have used ecu with the same number vw cc i replace it but my car star and going off code ecu star blocking by immobilizer p1570
hey I had the same exact year modeling everything and the same problem what was the outcome how did you end up getting it programmed
I have an 06 mazda 3 need to program it to the car and van i without a computer
cj mcneil hey were you able to do it , I have the same exact car
can i reprogam my 05 dodge dakota with a solus pro?
No
I have a Silverado 2005 v6 I did a Engine swap to 5.3 got a complete swap but need to install correct vin from truck is it possible with this snap on tool ? Thanks in advance
No. Need mdi from gm
Cool video can I do the same thing a Chevy Ecotec 2.4 09 I'm doing a engine swap to my Baja Bug I don't have the VIN number
Swap theft, ecm and bcm and it will start
Can you program a used ECU in a Mercedes or BMW?
Yes we can it all depends on the Ecu part number
My Car is a mess, old computer fried got a new reman one was the wrong one they sent back my original to me , my motor has been changed out once , they lost my key ans my eis , they never paid me back or sent back original parts ,
Ordered computer and eis , carkey from them , car still wont start :(
I purchased this scan tool thinking that I was going to be able to do the vin rewrite but do you scan tool that I got does not have that option where yours is listed. I have software version 14 or something with European added but I don’t see the option to write the Vin. How can I add that function and if you know how much it would cost any information would be appreciated thank you
Its only the american software that does it on solus pro. The updates was better for american cars. European is so so bad. You need the newer models
@@garyhoverington1398 i ended up buying a launch x431 v+ pro. This cost $900.. i was still not able to change the vin on my 2003 ford f150.. i am however able to change the vin on newer cars like my 07 c230 benz and 05 porsche. Im still researching how to do it on the f150..
@@xjaimevila you can do it on ids. Also ktag. Most people who do remap can manually write vin number
@@garyhoverington1398 im actually looking at ids now. The version i got doesnt have 2003 f150 series. I have the ids v86 but i dont have the cable yet. I was looking at the red box clone for vcm II but i have to get another version of ids to see if it has the 03 f150.. ill have to look into ktag.
@@xjaimevilaI have the same scan tool it works good some features aren’t supported but it’s good.
What model scan tool is that
It says solus pro
@@CowbellofPoverty email me with the info on that scanner leevondgilmore@gmail.com I need your help in California the vin number has to match the ecm some how my ecm number was changed when I used a flash tuner.
where can i get this scanner
Snap on
Can this happen on a 2009 Civic?
No
Hi i like your video question can i programm my 2015 infiniti q50 hybrid new ECU with Solus Pro
No you cant. Has theft and need nastif id to acess rolling cod3
What Happens if you dont do a vin change ?
You won’t pass deq state emissions
VEHIX411 My Idle Is Off :/ After Ecm Swap .
Is it same part number ecu
VEHIX411 Yes It Is
@@vehix411hey can you help me out I wrecked totaled my car but I bought a used 1 and I need help
How do u shirt out edb? U never showed that ? With out that the rest of the video is isless
Learn how to speak English
Not enough info !
Watch the video it’s all there from A to Z
Can you please help us we have mitsubishi outlander 2016 dosent start after replacing ECU now the IMMO asking for the following keyless operation system service required.
So that means we need to program the key to the new ECU and we don't have the original ECU to do so.
How can i get back the old data for it?
Thanks for your time.
You need to program new Ecu with any key programming scanner