How to Replace Water Pump 2003-08 Toyota Matrix
Vložit
- čas přidán 3. 09. 2020
- Buy Now!
New Engine Water Pump from 1AAuto.com 1aau.to/ia/1AEWP00182
The water pump keeps coolant flowing through your engine. Common failures of the water pump will leave the coolant leaking, or stagnant. Both will lead to overheating if left untreated. Install a new engineered to fit water pump from TRQ for total peace of mind. This video shows you how to install a TRQ water pump in your 2003-2013 Toyota Matrix.
• Check here for more videos on the 2003-13 Toyota Matrix: • Toyota Matrix 1st Gene...
This process should be similar on the following vehicles:
2003 Toyota Matrix
2004 Toyota Matrix
2005 Toyota Matrix
2006 Toyota Matrix
2007 Toyota Matrix
2008 Toyota Matrix
Tools you will need:
• Pocket Screwdriver
• Pry Bar 1aau.to/oa/1AXAA00020
• 10mm Wrench 1aau.to/oa/1AXAA00010
• 14mm Wrench 1aau.to/oa/1AXAA00010
• 10mm Socket 1aau.to/oa/1AXAA00017
• 12mm Socket 1aau.to/oa/1AXAA00015
• 14mm Deep Socket
• 19mm Socket 1aau.to/oa/1AXAA00043
• Coolant Funnel Set 1aau.to/oa/1AXAA00116
• Ratchet 1aau.to/oa/1AXAA00016
• Socket Driver
• Socket Extensions 1aau.to/oa/1AXAA00015
• Torque Wrench 1aau.to/oa/1AXAA00044
• Brake Parts Cleaner
• Dielectric Grease
• Gloves 1aau.to/oa/1AXSS00048
• Paper Towels 1aau.to/oa/1AXSS00035
• Petroleum Jelly
• Safety Glasses 1aau.to/oa/1AXAA00343
• Drain Pan 1aau.to/oa/1AXAA00320
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXAA00280
• Wire Brush 1aau.to/oa/1AXAA00079
Subscribe: / @trq
Check out our playlist:
Toyota Matrix 1st Generation 2003-13: • Toyota Matrix 1st Gene...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Hello .. please what is the torque wrench brand you used ?
Nice Video. Clear voice. No music. And you gave us the relevant steps without extraneous information. Thumbs-Up! I now have confidence in doing this myself.
+Mark Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
This is how a video should be. Good video angles, good lighting, clear voice, naming the sizes for each nut…you got it all!
This guy is excellent and has a good speaking voice. Clear, concise easy to follow directions and no awful background music!
5:48 How you got all the other bolts out, that is the hard part that needs to be shown.
Great video! The only thing I would say is. Don't use an impact on the engine cover, it's wildly excessive and can cause the valve cover bolt to come out with the engine cover. It also transfers energy on the right stud directly to the valve cover bolt and could potentially strip it out.
Didn’t think oem had a gasket. Just the round rubber seal. Maybe aftermarket comes with gasket?
Professional video! 👍
nice lighting and clear video angels. perfect explaining things.
Five stars.
What’s the Aisin gasket part #? Mines didn’t come with it.
How did you unscrew the other screws of the water pump?
Excellent video! Great instructions and camera work. Thank you!
Oh ok I just went into the descriptions. I see the water pump. Wow thanks for including everything you used in there too! Not just the part and torque specs, but the tools as well with links jic we want to get them as well! Subbed! 👍🏽👍🏽
I would add, taking off front right tire and peeling fender shroud back aids in access to lower bolts, otherwise bad words may be said. Also some after market pumps are different. Beware what you buy and make sure you have enough of the long bolts if pump is different. The extra bolts that came with the pump I bought were not used. Had to go to the fastener supply to buy 2 more long bolts.
+larry weinberg Thanks for the feedback! 1aau.to/m/Shop-TRQ
Dont use o-ring and gasket both. One or the other, o-ring is better. Use a little RTV on either
Great video straight to the point 👌 please do more of this corolla an matrix videos thanks for the help
"now that we have all our bolts out of there",,,,,, POOF magic! I must have missed something?
"now that we have all our bolts started",,,,,,, POOF magic again! I must have missed something else?
Awesome instruction. Good lighting and camera angles as well. Question. How do you get the pump bolt off that is behind it and out of view? Also, how much coolant does it take? Would I measure this by watching the fill line on the reservoir?
Sorry you skip too many damn steps. I'm having an issue getting the bottom 2 screws off the water pump but u skipped how you got it
Nice showing. Thanks
Thanks for sharing your knowledge
Great video,,you are a great teacher, thanks
Muchas gracias ¡saludos dsde Panamá!🖒
Thanks alot for the video did the rad and waterpump and new serpentine belt thanks to your video!
wow ...very good tutorial thank you..
Good 👍 good 👍👏
This is awesome! Thank you for the detailed video, including the torque specs. Also, what brand waterpump is that? Do they all come with dual type gaskets?
Thank you so much !!
Why mine doesn’t have that paper gasket do I need that one or just the rubber seal ok?
Rubber usually better
where's the bolt to compress the piston? I don't see what you're talking about
wow good video !!!! so cool!!!! good info
Buena explicación
Thank you😊
One huge question that i cant find the answer to. On a 2006 Toyota Matrix base, what is the direction of the impeller? I see "exact fit" that are reverse and clockwise (standard) i got rid of the old broken water pump and since the new one is in place i have no heat and a cold lover rad. Hose. Thinking the new pump is pushing water the wrong way!
Is it the same procedure for next generation with 1.8l engine?(2013)
Is the water pump really torqued with inch pounds and not foot pounds?
Only issue I just found out is if your replacing the water pump with an aftermarket one from a chain auto parts store you might have an issue with those 2 longer bolts. I need to know exactly what size those smaller bolts are so I can find two more where the two longer ones won't workout with my aftermarket water pump.
+MonkeyMan Thanks for the feedback! 1aau.to/m/Shop-TRQ
Thanks..
What size are the bolts on the water pump itself? Also do you really need to drain your coolant to change the water pump?
Yes, that's what the first step of draining the radiator was all about
Where is the thermostat housing?! I cannot find a single tutorial on where it is on a matrix and can't find it anywhere
Where can I get that paper gasket?
80 inch what's the convert that into foot pounds
Muy bueno,solo lo q no entendí es por q dise q el refrigerante es 50-50
Éso lo dice por si usaste anticongelante sin diluir, si lo usas diluido ya no es necesario diluirlo
Why does jt keep looking like rightly loose?