How do they do... How to do piston ring and scavenge space inspection on main engine... On ships

Marine engineering basics #merchantnavy #job at sea #Maintenance job in engine room #engine room jobs # scavenge space inspection #piston ring inspection #main engine #electronic engine#second engineer jobs #enclosed space entry #CHECKS on piston ring #how to do enter scavenge space #how to check gas meter #precaution before entering scavenge space # things to carry for scavenge inspection #how to use elcometer#how to check thickness of piston ring coating #basic information on piston ring inspection
Follow us on :
Facebook - www.facebook.c...
Instagram -
/ marine_engineering_basics

[@JhonySantos2022]

I have no words to say thank you!! God blesses you!

[@marine-knowledge-basha]

You are so welcome..

[@shubhamtyagi9122]

Very impressed with the precise and correct information imparted in this video. Great Job !!!!

[@marine-knowledge-basha]

Thank you very much sir... Requesting you to share our channel with ur friends and subscribe

[@nyanlin770]

VERY GOOD VIDEO SIR. AS A NEWLY PROMOTED SECOND ENGINEER, I GOT A LOT OF KNOLEDGE FROM YOUR VIDEOS. THANKS A MILLION.

[@marine-knowledge-basha]

You are most welcome

[@AmitKumar-ic6dd]

Thank you very much for posting these videos. Very helpful for juniors.

[@marine-knowledge-basha]

welcum sir...

[@sreelakshmikumar1345]

thanks to the effort and work put into this video .....expecting more videos..

[@marine-knowledge-basha]

Sure sir

[@StudyMarinewithUttamjakhar]

Gajab...it's very helpful video

[@marine-knowledge-basha]

Thank you so much 😀

[@benitocbf8788]

Nice video sir, thank you. I`m 4th engineer from Brazil and this video was so helpful for me. thank you very much

[@marine-knowledge-basha]

Thanks for your good compliment sir..requesting you to share our channel with ur friends and subscribe...

[@srinathgopinath7964]

Nice Informationive video. The Way you present in Good. Innocent,Humble and easy way to grab ideas for those hu r new even!!
Great job

[@marine-knowledge-basha]

Thanks for your good compliment sir.. Keep supporting

[@ogegbenewisdom2449]

i am so grateful for this video sir, keep doing the great work

[@marine-knowledge-basha]

Thank you sir... Requesting you to share our channel with ur friends and subscribe

[@bvprasanthprasanth6056]

Thank you sir for providing good information regarding scange space inspection.

[@marine-knowledge-basha]

Welcum sir.. Requesting you to share our channel with ur friends and subscribe

[@samipkapadia1995]

amazing job sir... people like you keep us inspired.....

[@marine-knowledge-basha]

So nice of you.. Thanks for your good compliment.. Keep supporting

[@alexflarance1996]

Excellent video sir.keep share your experience with us

[@marine-knowledge-basha]

Thank you sir.. Fr sure vl do.. Keep supporting

[@vipinlalxplod5271]

Good video and much informative sir

[@marine-knowledge-basha]

Thanks for your compliment sir... Pls share our video with ur friends and request to subscribe.. 😊

[@rucheer0037]

Also I’d like to add up the lashing wire are tied onto the bolt head in such a way that they’d avoid slackening of either of the bolts which are tied in pair!!! Very informative video sir!! Looking forward to sail with you as even I’m from BSM, sailing as JE. Thanks a lot for the information sir, very helpful and useful

[@marine-knowledge-basha]

Ur very crt sir... Thanks for your comment.. Keep supporting..

[@freakkyliferishav6598]

Very informative video

[@marine-knowledge-basha]

welcum sir....

[@ravindraudakumbura4219]

Very useful video. Thank you sir

[@marine-knowledge-basha]

Ur welcum sir... 😁

[@polkpolkov1094]

Many thanks ! Very good work !

[@marine-knowledge-basha]

Thank you sir... Requesting you to share our channel with ur friends and subscribe

[@polkpolkov1094]

@@marine-knowledge-basha Thank you ! Necessarily!

[@enginejobstvtrapz4469]

Hello i am a filipino seafarer .Very nice i learn a lot from you very details ang good explaination looking forward to your next video godbless.

[@marine-knowledge-basha]

Thanks and welcome.. Keep supporting... Please share and subscribe our channel with ur friends...

[@sultanhussain6051]

Well done 2nd sahab ...Really appreciate. One more request kindly share the video of fuel pump high pressure pipe to the injector, how to over hauled, what needs to check and what measurements are to be taken .
Love ,respect from Pakistan
Regards
Sultan Hussain 1st Engineer.

[@marine-knowledge-basha]

Thank you saab.. Vl share for sure..

[@athulroy3936]

Great effort and explanations ❤️
Thank you so much 🚢

[@marine-knowledge-basha]

Thanks for your good compliment sir...
Requesting you to share our channel with ur friends and subscribe

[@animalsdocumentary6600]

Very very helpful video May you always be happy 😊

[@marine-knowledge-basha]

Thanks a lot 😊

[@JaVenkataSubramanianJaVenkat]

Great effort sir.

[@marine-knowledge-basha]

Thanks a lot sir

[@brokenarrow5590]

Post max amount of videos if possible.(Boiler, pumps, generators).Thanks in advanced.

[@marine-knowledge-basha]

Sure vl do sir.. Keep supporting

[@sandeepsangwan9019]

Keep posting sir!
For meo class 4 for its very helpful. Thank you🙏

[@marine-knowledge-basha]

Thanks for your compliment sir... Requesting you to share our channel with ur friends and subscribe..

[@angelferrer6]

Excellent inspection.

[@marine-knowledge-basha]

Thanks sir.. Keep supporting..

[@akashmukherjee2503]

Excellent initiative by u 2nd..

[@marine-knowledge-basha]

Thank you sir.. Keep supporting

[@Nagaraju8700]

Nice video sir , 👌 piston skirt and piston nuts and bolts are torque tightened , in which model and make Hydraulic tightened sir ? Information is good would like to know that sir , thanq very much for your support to all levels in Marine Engineering , good energetic person 👍

[@marine-knowledge-basha]

Thanks for your good compliment sir... This hydraulic tightening i had seen in MAN B&W ME (ELECTRONIC ENGINES).

[@makinistangmandaragattv5560]

Good day 2E...very informative.T.Y.
Special request... Possible also you make blogg about cylinder oil settings

[@marine-knowledge-basha]

Thanks for your good compliment sir... Vl do fr sre sir

[@makinistangmandaragattv5560]

@@marine-knowledge-basha welcome future CE.

[@marine-knowledge-basha]

@@makinistangmandaragattv5560 Thank you for your wishes sir

[@aruntchandran7505]

thank you sir

[@marine-knowledge-basha]

So nice of you

[@junaidkadri644]

sir
why there is relief valve inside the scavenge reciver there will be always low pressure inside while running.how will the receiver will pressurize?

[@Seamanlife1997]

thank you sir its very important

[@marine-knowledge-basha]

Most welcome sir.. Keep supporting

[@vaibhavnayak626]

Best information

[@marine-knowledge-basha]

Thank you sir..

[@mec6953]

sir, good day. take my regards.
if i inspect scavenge trunk, and find that, one specific unit has too much oil+sludge accumulation inside the scavenge trunk comapre to other units. what could be the reason? why too much accumulation or how the oil is coming?

[@marine-knowledge-basha]

Thanx for your query sir...
Accumulation of sludge depends on hw speed and load the engine s running.
Usually u can hv visual inspection on Accumulation.
If you find abnormal sludge that may be due to
* Drain line could b clogged.
* Fuel injection is not proper
* Fuel injecttor leaking.
* improper tightening of fuel injectors.
Hope this reply will satisfy your query

[@mwbgaming28]

What's the average pressure and temperature in there while the engine is running and the turbo is spooled up?

[@marine-knowledge-basha]

It's average pressure is around 1 bar when aux blower is not running...

[@mwbgaming28]

@@marine-knowledge-basha I see, I ask because I heard a story of some guy getting stuck in there and apparently he died from high pressures and overheating

[@marine-knowledge-basha]

@@mwbgaming28 sir in this case the guy must have been inside the chamber because of intentional or accidental closing of scavenge door without inspecting for any person inside.

[@mwbgaming28]

@@marine-knowledge-basha he went in there without telling anyone and someone closed the door on him, the captain though he left the ship and was ditching work, so he started the engine and the ship departed on a trip that took a few days (they were going to a dry dock or something for major maintenance) and they found the guy dead in the air scavenging receiver
Do you think it was temperature or pressure that ended up killing him? (Seeing as the combustion chambers are directly exposed, I would think it would be both)

[@rukhsarrukhsar8334]

Good job man 👍

[@marine-knowledge-basha]

Thank you dear

[@sumongazi9050]

Nice video❤️

[@marine-knowledge-basha]

Thanks sir

[@abdulkader2596]

Sir lot a thanks

[@marine-knowledge-basha]

Thank you sir.. Requesting you to share our channel with ur friends and subscribe

[@nandhu5800]

Thanks a lot very useful

[@marine-knowledge-basha]

welcome sir.. pls keep supporting

[@mrsingh3852]

sir which instrument u used to take the thickness.

[@yinkaadu8092]

Great job sir.
Please what is the name of the digital equipment you used to take the thickness of the piston rings

[@marine-knowledge-basha]

Thank you for your good compliment sir..
Elcometer is the name of the equipment..
Requesting you to share our channel with ur friends and subscribe

[@user-bj9kf3rm2u]

Sir, thanks for the video. I have a question btw. Where can I get the measuring device for piston ring wear? Like how can I get that device which can let me know alu-coating and cermet-coating wearness?

[@marine-knowledge-basha]

U can order through maker... Its called elcometer..

[@user-bj9kf3rm2u]

@@marine-knowledge-basha And if the ship is using cermet coated piston rings, we can order that, right??

[@narendraniranjanmathiyaras5255]

super na ...❤️❤️❤️

[@marine-knowledge-basha]

Thanks dear

[@catopedia1167]

👍👍

[@marine-knowledge-basha]

Thanks boss

[@lavanyaarora6951]

Perfect👏

[@marine-knowledge-basha]

Thanx a lot.. Keep supporting

[@sanyammoudgil8339]

Thank you soo soo sooo much ♥️

[@marine-knowledge-basha]

Welcum sir... Keep supporting

[@mec6953]

sir, i am a cadet. may i ask you a question about liner wear?
is adhesive/scuffing wear and micro seizure on liner surface is same? or adhesive wear and micro seizure different case?

[@marine-knowledge-basha]

thanks for your good question sir..
* Adhesive wear is caused by loss of oil film and leads to piston and liner to have metal to metal contact that may reach to localised welding and leads to scuffing..
* Abrasive wear is caused mostly by cat fines which is contaminated in fuel oil. This leads to rubbing of Abrasive wear can be caused by hard asperities in the components rubbing against each other or by hard
particles from contaminants such as catalyst fines (cat fines) from fuel oil. These hard particles embed
themselves into the piston ring and/or liner surface and breach the oil film, thus abrading the surfaces and
wearing them down in high speed.
* Micro seizure indicates the beginning of wear and can be rectified by increasing the cylinder oil feed rate.
I beleive this reply will satisfy your query,

[@mec6953]

@@marine-knowledge-basha ❤❤❤❤

[@sultanhussain6051]

👍

[@marine-knowledge-basha]

😊

[@campincar449]

Nice sir but try to do dubbing after shoot. Which we can clearly what you are telling. Don't mistake me sir , now it is really testing my patience. Please consider this.

[@marine-knowledge-basha]

Sorry for the inconvenience sir..vl correct it in near future... Thanks for your good advise..

[@neyanmahizh4293]

super explanation sir ,and can you uplode vedio on crankcase inspection

[@marine-knowledge-basha]

Thanks sir.. For sure vl do.. Pls giv me sme tme..

[@marine-knowledge-basha]

Requesting you to share our channel with ur friends and subscribe

[@jiwanjanoti8620]

Good but
I want to ask

[@marine-knowledge-basha]

Pls go ahead vth ur query sir

[@binusankarsankar9322]

👏👏👏🙏🏻thks sir

[@marine-knowledge-basha]

Welcum sir...

[@TheRayryu1]

Hit you up!!

[@marine-knowledge-basha]

👌

[@kenikabilanfernando6074]

Tq sir

[@marine-knowledge-basha]

Welcum sir..

[@binusankarsankar9322]

🙏🙏🙏🙏🙏

[@marine-knowledge-basha]

❤️

[@rajanmenon7633]

How many flaps are there??

[@marine-knowledge-basha]

Sir the number depends on size of engine

[@pravincg1537]

How to take butt clearance new piston ring and old piston ring????? Pls rly anna class 4 oral question

[@marine-knowledge-basha]

thanx for your query Pravin.. Vl upload a vdo on it shortly

[@marine-knowledge-basha]

Just gv me a day vl upload soon.. It will b easier to understand if is shown in vdo... Kindly bare vth me

[@marine-knowledge-basha]

Hd uploaded it requested vdo. pls watch nd comment if there is any..

[@dcebalbotea313]

Vessel's name?

[@marine-knowledge-basha]

Its a container ship sir,....

[@bhuvanayyanar6524]

Sir , what is H5 type piston ring sir?

[@marine-knowledge-basha]

Sir.. H5 type piston rings come with al and ceremot coating.. This type of piston rings are used in latest ME engines.
Hope this reply will satisfy your query

[@Hayatikavak1969]

👏👏👏👏👏👏👏👏🙏🙏

[@marine-knowledge-basha]

Thank u sir..

[@fragkosioannis6768]

Mpla mpla mpla indians ......

[@marine-knowledge-basha]

..

[@Anjul_S]

Excellent bada saab! But one request to you in such cases agar aap video record karke fir video me samjha den to hum juniors ko bahut aaram hoga.

[@marine-knowledge-basha]

sure saab will do ....jrur karegha

[@prasanthkutty1073]

👍

[@marine-knowledge-basha]

🙏