HOW TO: Remove Bearings from Dirt Bike ENGINE CASES

This is a step by step HOW TO video on the process of removing your engine case bearings on your dirt bike! If you are doing a complete engine tear down and replacing the bearings, this video shows you how to remove them in a few simple steps! I have a linked the below the Tusk Bearing Remover Tool that you will need in order to get at the ones where you don't have to the other side.
🔥TUSK BEARING REMOVAL TOOL: www.rockymount...
🔥SOCIAL MEDIA:
Instagram: / greghitchko
🔥EMAIL [e-mail] with any questions or inquiries
Looking for parts and tools?! Rocky Mountain will no doubt have them in stock. Check out the links below for all of the products used in the video. I greatly appreciate your support when you do that!
🔥RMATV/MC OEM Parts: www.rockymount...
🔥MOTION PRO TORQUE WRENCH ADAPTER: www.rockymount...
🔥MAXIMA 80W MTL TRANSMISSION OIL: www.rockymount...
🔥MAXIMA COOLANOL: www.rockymount...
🔥MAXIMA QUICK MIX CUP: www.rockymount...
🔥MAXIMA SUPER M PREMIX: www.rockymount...
🔥RATIO RITE MEASURING CUP: www.rockymount...
****TOOLS****
🔥DEWALT IMPACT GUN: amzn.to/3wQgTl8
🔥DIGITAL CALIPER MEASURING TOOL: www.rockymount...
🔥TUSK STEERING STEM BEARING INSTALLER: www.rockymount...
🔥TUSK CLUTCH HOLDER: www.rockymount...
🔥TUSK CRANKCASE SPLITTER: www.rockymount...
🔥TUSK FLYWHEEL PULLER: www.rockymount...
🔥TUSK CRANK PULLER/INSTALLER: www.rockymount...
🔥TUSK BEARING REMOVAL TOOL: www.rockymount...
🔥MOTION PRO STEERING BEARING RACE DRIVER: www.rockymount...
🔥BENCH BUFFER: amzn.to/3tEmFG1
🔥PRYME CLEANING WHEEL PACK - 8 Inch: www.prymemx.co...
PRYME FIBER FLAP WHEEL PACK: www.prymemx.co...
🔥DREMEL: amzn.to/3lJal4L
🔥DREMEL MINI WIRE BRUSHES: amzn.to/3An55bq
🔥EAGLE ONE ALUMINUM WHEEL CLEANER: amzn.to/3BCCVdO
🔥WIRE BRUSHES: amzn.to/37rtLTB
🔥WIRE TUBE BRUSHES: amzn.to/3fHw35q
🔥MAP GAS TORCH: amzn.to/2RIbvR7
🔥BREAKER BAR 1/2' DRIVE: amzn.to/39vErC7
🔥STRIPPED BOLT HEAD REMOVER SOCKET SET: amzn.to/3cQXWHf
🔥MOTOSPORT ENGINE STAND: www.rockymount...
CERAKOTE TRIM COAT: amzn.to/3hPfm8P
Use GREG10 to save at PHATHEAD RACING HEADS: lukesracing.co...
This video is NOT sponsored. Some product links are affiliate links which means if you buy something I'll receive a small commission. Thank you for supporting the channel!

[@jonnoMoto]

Easiest I find is to put in the oven at 140c with bearings facing down. They just fall out. Same for installation. Heat it to 140c and drop bearings in.

[@GregHitchko]

That also works great as well!! Definitely to install them without a doubt

[@genericjonathan4115]

i’m gonna try this

[@samanthagriffin7667]

Where would you be without Tusk? 🤣

[@GregHitchko]

Where would i be without YOU! 😘

[@wyattcitizenzap4539]

if you are very careful instead of pulling a bearing you can cut it out with a drumel. you must be very careful and precise but im an idiot and ive done it successfully.

[@GregHitchko]

My hands aren't that steady haha but I commend you for doing it that way 🙌🏼

[@SquareBodyK5]

That's dumb and a waste of time.

[@wyattcitizenzap4539]

@@SquareBodyK5 i had to do it before. the bearing would not come out and i didn't want to damage the case by banging it out so i used a drumel. this was on a 1984 ATC 200X idk if it was an OEM bearing or if someone slapped in the wrong one but the fucking thing would not come out.