Video není dostupné.
Omlouváme se.
TURBO Holset 55no.in New Holland 3600 Tractor🚜🔥|Turbo Sound😍| GS Turbo Moga | Jeep Market Moga😟
Vložit
- čas přidán 3. 01. 2024
- #turbo #tractor #holland #moga #punjabivlogger
BEING PENDU VLOGS PRESENTS-:
TURBO Holset 55no.in New Holland 3600 Tractor🚜🔥|Turbo Sound😍| GS Turbo Moga | Jeep Market Moga😟
Location-:Dosanjh Road Moga India✅
Cast-: Arsh Dhunna,Mehtab Singh,Sehaj Heir
Camera Used-: IPhone 12 Pro Max📱
#turbo #tractorvideo #punjabivlogger #trending
Tractor Turbo Explain-:
A turbocharger incorporates an exhaust-driven turbine wheel. That wheel is contained in a volute, which is a snail-shape housing. That wheel is also connected via a shaft to another volute that contains a centrifugal compressor wheel that sends the charge air to the intake manifold. Abstract: Turbochargers are centrifugal compressors driven by an exhaust gas turbine and employed in engines to boost the charge air pressure. Turbocharger performance influences all important engine parameters, such as fuel economy, power, and emissions. It is important to understand a number of fundamental concepts before moving on to a more detailed discussion of turbocharger specifics. A turbocharger consists of a compressor wheel and exhaust gas turbine wheel coupled together by a solid shaft and that is used to boost the intake air pressure of an internal combustion engine. The exhaust gas turbine extracts energy from the exhaust gas and uses it to drive the compressor and overcome friction. In most automotive-type applications, both the compressor and turbine wheel are of the radial flow type. Some applications, such as medium- and low- speed diesel engines, can use an axial flow turbine wheel instead of a radial flow turbine. The flow of gases through a typical turbocharger with radial flow compressor and turbine wheels is shown in Figure 1 [Schwitzer 1991]. Center-Housing. The turbine-compressor common shaft is supported by a bearing system in the center housing (bearing housing) located between the compressor and turbine (Figure 2). The shaft wheel assembly (SWA) refers to the shaft with the compressor and turbine wheels attached, i.e., the rotating assembly. The center housing rotating assembly (CHRA) refers to SWA installed in the center-housing but without the compressor and turbine housings. The center housing is commonly cast from gray cast iron, but aluminum can also be used in some applications. Seals help keep oil from passing through to the compressor and turbine. Turbochargers for high exhaust gas temperature applications, such as spark ignition engines, can also incorporate cooling passages in the center housing. turbocharger bearing system appears simple in design, but it plays a key role in a number of critical functions. Some of the more important ones include: the control of radial and axial motion of the shaft and wheels and the minimization of friction losses in the bearing system. Bearing systems have received considerable attention because of their influence on turbocharger friction and its impact on engine fuel efficiency.
With the exception of some large turbochargers for low-speed engines, the bearings that support the shaft are usually located between the wheels in an overhung position. This flexible rotor design ensures that the turbocharger will operate above its first, and possibly second, critical speeds and can therefore be subject to rotor dynamic conditions such as whirl and synchronous vibration.
Seals. Seals are located at both ends of the bearing housing. These seals represent a difficult design problem due to the need to keep frictional losses low, the relatively large movements of the shaft due to bearing clearance and adverse pressure gradients under some conditions.
These seals primarily serve to keep intake air and exhaust gas out of the center housing. The pressures in the intake and exhaust systems are normally higher than in the turbocharger’s center housing which is typically at the pressure of the engine crankcase. As such, they would primarily be designed to seal the center housing when the pressure in the center housing is lower than in the intake and exhaust systems. These seals are not intended to be the primary means of preventing oil from escaping from the center housing into the exhaust and air systems. Oil is usually prevented from contacting these seals by other means such as oil deflectors and rotating flingers.
Turbocharger seals are different from the soft lip seals normally found in rotating equipment operating at much lower speeds and temperatures. The piston ring type seal is one type that is often used. It consists of a metal ring, similar in appearance to a piston ring. The seal remains stationary when the shaft rotates. Labyrinth-type seals are another type sometimes used.
Instagram-: www.instagram....
Gs Turbo Instagram-: www.instagram....
Like/Comment/Share❤️
Thanks For Watching🙏🏻❤️
Bhaji bhut vadia aa
❤❤ਬਹੁਤ ਵਧੀਆ ਞ❤❤
Nice ❤❤❤❤
❤
Kharcha kinna
Aunda
dosto video Moga de good. please do less ok report ,ok report ,few minutes later its bakwas. need quality material topic , more info on turbo install detail , cost, young boys you can do better , watch language other guy swearing ,otherwise theek a
Selincer da ki price aa
Kinna kharcha aa gya bai nd kinne hp kru tractor nu???
Turbo da price ki a vr g