which pumps have adjustable pressure so old geysor dont burst and pipes dont leak. What should pressure be set in psi or kg per cm sq to a safe level for old geysors and pipe fittings
Impressive video and I like the music. Video is fast, can digest better if slower, need to repeat and pause several times. Suggestion: it is more appropriate to have the test valve located at the highest point for venting air.
Excellent and informative video!...I have a few Qs though - 1) What is the need for a Press. Reducing Valve(PRV) as I understand the pump has a built in pressure regulator ? 2)Is it necessary to put the metal length of pipe on the discharge? 3) Is the bypass achieved automatically during power failure?(though gravity)?..meaning no additional hardware required? Thanks!
Hello sir... Thank you for your response to this video. For the two questions that you have the replies are as follows: 1. The yellow colour kit which is shown in the video is a pressure kit and not a pressure regulator. Th kit's function is to avoid dry run of the pump while a PRV (Pressure relief valve) is to reduce the pressure as per the customer's requirement. 2. The bypass which is given is for the normal flow of water during power failure. No additional work is to be done during power failure as the water will itself flow through gravity. During power failure the pressurized water will not be available whereas the water will flow at normal pressure itself.
I think you only need NRV for the bypass pipes so that during working condition of the pump the water doesn't go back into the tank. The rest is all the same
Please explain various types of pressure pump( like some with tank and some without tank) and installation types whole house or one single bathroom... Thanks
@@sumitechpumps9933 is there any booster pump which can run on 12 volt DC battery .I have two bathrooms and pressure flow is very less when light goes off . booster pump does not work .give your suggestions
The three pipes have two ball values each with a total of 6 ball valves used in this plumbing circuit. But from what I can see, they serve no purpose because all the three pipes are connected to each other down below where the booster pump is connecting to them. I think the ball values need to come after booster pump outlet is connected. Then only each of the ball valve will be controlling the flow in each of them. For example, if the three pipes are used to supply water to 3 different bathrooms and if you want to stop water in only one of the bathroom, then with the above connections this is not possible. With the given connection diagram you need to stop water in all the 3 bathrooms. Kindly think about this and make improvements.
First of all, Let me thank you for such amazing video. I would like to know what PRV(pressure relief valve) and Non return valve NRV do you recommend to use.
Tech Pumps Tech Pumps PRV - Pressure relief Valve is used to reduce and release the pressure from plumbing line NRV - Non Return Valve is used to prevent backflow of Water
Can we use this to increase the pressure of water from Borewell to OH tank.We have a jet pump , but the water is treated in softening plant installed on line, which reduces the flow considerably and takes time to fill the tank.
I have crompton 0.5 HP mini cruz II pressure pump with pressure regulator kit and it automatically switches on and off every 1 minute, It runs for 15 secs and then stops. It keeps on repeating. WHat may be the problem and what can be the solution to it. And there is lot of pressure in water. Can i reduce it.
Nice fancy impressive graphics WRONG !!! For starters just the vibration of the motor on the inlet side will break those pvc fittings and leak. Should always use a flex on the inlet. Not any old flex a HD stainless steel with pre fab connectors. Ty
Good morning . Thanks for your enquiry. .This pump is to be installed near over head tank on delivery line to your bathroom as shown in CZcams video .Nearby the motor pump 15amps plug switch will be kept and it will be kept always on,this part will have to be done by a plumber cum electrician . When you open the tap the pump will automatically runs. after closing the tap motor automatically switch off . For further clarification please call my no. 7092942220 share your no to call back .Regards Gowri
Dear Sumaira Khalil. Thankyou for your question . It depends on number of bathrooms you use at a time. We would be more than happy to further suggest and advice on the best option in accordance to your need . You can either call 98 84 74 64 89 or log onto www.www.techpumps.com/ for further details. Look forward to hear from you
which pumps have adjustable pressure so old geysor dont burst and pipes dont leak. What should pressure be set in psi or kg per cm sq to a safe level for old geysors and pipe fittings
What a fine and detailed demonstration....
thank you
Impressive video and I like the music. Video is fast, can digest better if slower, need to repeat and pause several times. Suggestion: it is more appropriate to have the test valve located at the highest point for venting air.
Thank you.. noted the feedback!!
Excellent and informative video!...I have a few Qs though -
1) What is the need for a Press. Reducing Valve(PRV) as I understand the pump has a built in pressure regulator ?
2)Is it necessary to put the metal length of pipe on the discharge?
3) Is the bypass achieved automatically during power failure?(though gravity)?..meaning no additional hardware required?
Thanks!
Hello sir... Thank you for your response to this video. For the two questions that you have the replies are as follows:
1. The yellow colour kit which is shown in the video is a pressure kit and not a pressure regulator. Th kit's function is to avoid dry run of the pump while a PRV (Pressure relief valve) is to reduce the pressure as per the customer's requirement.
2. The bypass which is given is for the normal flow of water during power failure. No additional work is to be done during power failure as the water will itself flow through gravity. During power failure the pressurized water will not be available whereas the water will flow at normal pressure itself.
Bhai I like it job thanks many many thanks bhai
I think you only need NRV for the bypass pipes so that during working condition of the pump the water doesn't go back into the tank. The rest is all the same
Great work guys!
Thank You
Do this pumps have impellers or pistions
Please explain various types of pressure pump( like some with tank and some without tank) and installation types whole house or one single bathroom... Thanks
Please inform your contact num enabling to have more details or please call us 7092942220
@@sumitechpumps9933 is there any booster pump which can run on 12 volt DC battery .I have two bathrooms and pressure flow is very less when light goes off . booster pump does not work .give your suggestions
I install same setup in 5 line problem is that nrv work 2 line but 3 line nrv not work plzzz help mee how can I sollve
The three pipes have two ball values each with a total of 6 ball valves used in this plumbing circuit. But from what I can see, they serve no purpose because all the three pipes are connected to each other down below where the booster pump is connecting to them. I think the ball values need to come after booster pump outlet is connected. Then only each of the ball valve will be controlling the flow in each of them.
For example, if the three pipes are used to supply water to 3 different bathrooms and if you want to stop water in only one of the bathroom, then with the above connections this is not possible. With the given connection diagram you need to stop water in all the 3 bathrooms. Kindly think about this and make improvements.
Thanks for suggestion
First of all, Let me thank you for such amazing video.
I would like to know what PRV(pressure relief valve) and Non return valve NRV do you recommend to use.
Sir, please specify the application of Prv, Nrv and size, Thanks
@@techpumps8798 for home use. Pressure pump fixing. half inch.
PRV - Pressure relief Valve is used to reduce and release the pressure from plumbing line
NRV - Non Return Valve is used to prevent backflow of Water
Tech Pumps Tech Pumps PRV - Pressure relief Valve is used to reduce and release the pressure from plumbing line
NRV - Non Return Valve is used to prevent backflow of Water
Sir meeru valves off cheyaledu chudandi
Can we use this to increase the pressure of water from Borewell to OH tank.We have a jet pump , but the water is treated in softening plant installed on line, which reduces the flow considerably and takes time to fill the tank.
Please use inline booster pump between jet pump delivery and softner vessel inlet for quick fill
What about electricity consumption?
I have crompton 0.5 HP mini cruz II pressure pump with pressure regulator kit and it automatically switches on and off every 1 minute, It runs for 15 secs and then stops. It keeps on repeating. WHat may be the problem and what can be the solution to it. And there is lot of pressure in water. Can i reduce it.
Sir Kindly make a call to 96000 48309 for your Queries and get clarification
SUPER
Nice fancy impressive graphics WRONG !!! For starters just the vibration of the motor on the inlet side will break those pvc fittings and leak. Should always use a flex on the inlet. Not any old flex a HD stainless steel with pre fab connectors. Ty
please inform your contact number enabling to have more details or please call on us 9600048309
Please can u tell me How to reduce the pressures can u explain me in short..
By using pressure reducing valve
Diverter se hot line me return jayega
Suppose I have a solar water heater (non pressure model) how to go about making the booster pump connections. Any idea/help in this regard?
Please use it on delivery side of solar water heater
What software was used to make this presentation?
3ds Max
@@KALEIDOSCOPECHENNAI thanks bro
Welcom to my channel
Regards
Can this pressure booster use in submersible water pump
Definitely you can use
S Gowri
Definitely you cannot use as submersible.
How to install does it need to run 24 hrs
Good morning . Thanks for your enquiry. .This pump is to be installed near over head tank on delivery line to your bathroom as shown in CZcams video .Nearby the motor pump 15amps plug switch will be kept and it will be kept always on,this part will have to be done by a plumber cum electrician . When you open the tap the pump will automatically runs. after closing the tap motor automatically switch off . For further clarification please call my no. 7092942220 share your no to call back .Regards Gowri
Suppr
Thanks
How much it will cost
Please inform your contact number enabling to have more details about the booster pump or please call us 7092942220
Pump
Tell me for 10 bath room hp size moter??????????
Dear Sumaira Khalil. Thankyou for your question . It depends on number of bathrooms you use at a time. We would be more than happy to further suggest and advice on the best option in accordance to your need . You can either call 98 84 74 64 89 or log onto www.www.techpumps.com/ for further details. Look forward to hear from you
Please inform your contact number enabling to have more details or please call us 7092942220
no return wall
Non return valve to avoid reverse water flow
👍👍👍👍👍👍👍👍
Bustier pump.name.hinde
Please tell me for 10 bath room moter hp size ???????
Achieve your complications with K'A'RCHER !
Thanks
rong is ma 1 galti ha
Galet bro
Thanks