Never wear breathing protection when painting. Do not mask tire/well area. Always spray in a dry-floor environment. Only shake the can before spraying; NEVER shake during the spraying process. Smoke as many cigarettes as possible in life. Great video guys!
The problem is he’s pushing the cap on and off way too much. You end up getting tons of solvents instead of pigments. Run the length of each panel not small areas. You can hold the cam upside down spraying for about 5 seconds to lower the pressure in the cans so the paint goes on thicker. Also never spray the first couple sprays of the can on the vehicle. Spray it at the air a couple times till it sprays pigment and not just solvent then go to the vehicle.
@@roperfoerderer1594 lol no that's not the same thing, those speckles come from them holding the can too far from the vehicle. Instead of laying it on its being misted on
Great video, thanks. For anyone doing the same, it's important to wipe the nozzle at every chance, so keep a piece of cloth with you. Shake that can, alot, keep thta pressure going and work in a uniform pattern, keep following that wet line and move downwards. First coat should act like a tack, so just spray lightly and let it dry a bit, then you start spray painting.
I've been an auto body and paint man for 50 years now and I'd have to say' for what you were working with and giving credit when it's due' I would love to have you 2 guys paint all of my worst enemies vehicles.
Closer and move quickly you'll get less dry spray and less oranges peel in the finish product and keep the can parallel to the panel you're getting heavy streaks in the roof
Great job painting the small dents the tires and rims. Should wet the floor for dust and first layer light paint . Three layers micro thin paint do about 10 then let dry the sand it out then 2k clear coat it
@@jessemoss2548 when I used to work in home fire restoration I used to use a aluminum oxide oil base primer for block and metal and would not cover my face fully, as I sprayed over head ..I would look like one of the guys from "Kiss " I would use petroleum jelly/ Vaseline to wipe my eyelids and face. i was very surprised on how well it worked, and it didn't burn my skin.. I imagine that it would work on the rubber .. ...prep? Or clean? Age old dilemma
@@christhopherlasher2828 a other good secret is liquid gold furniture polish , it has a chemical that very very gently breaks down wax and paint finish for an unbelievable finish on a paint job , it is so good that after a couple minutes of massage it will take dried Bondo off your hands, also the best homegrown secret for primer and wetal prep to accept and hold paint forever is DISTILLED VINEGAR! SOLVENT AND PREPSOL ARE TOO STRONG FOR RATTLE CAN PAINT.
Some times the new guys have to learn the hard way. I have a hard time watching them overspray the the glass, wheels, chrome, door handles and key holes. Also little or no prep...😖😖😖😵💫😵💫😵💫😵💫😬😬😬😈
Did this to an old work truck that was originally orange. We decided to go black to cover easily. We painted the truck in two phases. A couple of days before doing the large panels we used normal cans of black to do the door jams, gas filler, under hood and misc. areas. We also lifted the truck up and shot on three coats on the very bottom of all the panels where it would be hard to reach once the truck was on the ground. We let that cure for a few days then painted the large panels. What we learned was those large paint cans really liked to be warmed up before spraying. We bought 8 cans and set them in a two buckets of hot water for about 30 mins before painting the large panels. Each can was then shaken for about 5 mins. right before spraying and again about every minute. While I was spraying my buddy was shaking the next can. When ready to paint the cans were very warm but not uncomfortable to hold. First coat was a mist coat that we let tack for 10 mins. Second and third coats were full wet coats. It took me about 10 mins. to do the entire truck then we let that sit for about 20 mins. before starting on the next coat. After three coats the truck looked good and the paint was nice and smooth. After 2 yrs. it still looks good. We do normal washes and hit it with a spray wax a couple times a year but that is it for maintenance. Just wish they had more colors in those large cans.
Thanks for the input like I CLEARLY said in the video this was my first time painting a vehicle! Next time I’ll look you up and you can come paint it thanks for the Adsense
@@songdogseekers I'm not hating just trying to help I recommend putting a guide coat down then Sanding it with a block water and in a x motion then letting your cans still in boiling water for around 20minutes to build pressure in the can and make it spray Better
Let me start by saying I appreciate the content, nonetheless.... painting cars or not, ya'lls technique is atrocious. There are so many grievous errors made, like not testing a new can on a piece of cardboard before spraying, multiple overlapping passes on a single section of a panel instead of lighter consistent singular passes on the whole panel, not constantly shaking the can during the the spraying, not maintaining a constant even distance from the work piece, starting to spray directly on the panel instead of off the edge and coming into the panel... and just fyi, ya'll did like 10 coats, not 2. When you go over the same area 5 times in a single spray, that's 5 coats. Your end result could have been so much better.
@@songdogseekers even if it’s a work truck, you went through the trouble of buying supplies and filming the process. Have a little more pride in your work and stop using the excuse that it’s “a work truck.”
Hey guys good job everyone who’s talking crap are over the internet creeps you guys did good I don’t think they realize this is spray cans not a professional 8 thousand or 5 paint job keep it up man
For a work truck it looks pretty good to me. Is that the factory sprayer that comes on it. I just got a Chevy S10 that I'm going to paint and I'm thinking about using this.
I redid my Izsus NPR using the white. I waited a week and put 2k over it. It looks way better than the factory. It had 100’s of small rust spots and after 3 -4 years it has zero rust. I should probably finish it and do the 2 doors. I hate painting.
As a former bodyshop painter I can do this the Way it should look ( EXPERIENCE , KNOW MY SKILLS OF PAINTING WITH SPRAY GUN SO A CAN SHOULDN'T BE TO DEFAULT FOR ME most important the skill of spaying left to right correctly... ) not bad for a first timer 👍
Guys!!you don't know how much you have helped me.in my country,painting a simple small car goes as much as 350$ and that does not make it shine .i never knew there is good quality pressurelized paint out there.After painting,Do i need to use polisher for shinning?Love from kenya.
I did the 50 dollar paint job with Rusto and it didn’t last long but it was outside in all weather, but it did look great for a couple of years and it was a roll on not spray 8 coats and lots of sanding , and why only white and black paint how’s about some colors
So, is it just the spray can nozzle that makes this work good, or does this can have also more pressure as well???? Because if it's just the spray nozzle, couldn't you use any paint can with the same nozzle?!??
Actually, I thought the same thing and tried it on a conventional spray can. Turns out the turbo spray can nozzle only fits that specific turbo can. I ended up painting my index finger due to the spray escaping out of the bottom of the nozzle! Too bad cause it's a killer 10"-12" fan spray nozzle... Gotta come up with a way to adapt it to a conventional can🤔
Question- was the white you were glossing over with turbo can, was that white a white primer from a can or was it white paint from a can? Thanks, great video!!!
You're getting speckles because you're letting off the trigger while you're over the surface. It will spit paint when you go off and on over the surface. I can't wait to do this.
True dat ! I just did an88f-350, Ford blue and decided to mask and paint 1lpanel at a time due to my limited ability exhaust fan sumbich shines like a hounds tooth , I went extra wet to get my shine , and will rework several small runs as it cures. Gowey and shine , cleaning up a few runs on a beautiful shine is more of a worksaver that being shy with your rattle can and getting stuck having to buff out a whole vehicle for a shine.
my thoughts exactly... it's like they've never watched a single video on how to paint a car lol. Cutting each panel intro quadrants, and putting on nearly full coverage on the first pass... ffs. LONG, SINGLE PASS ALONG THE WHOLE PANEL, THEN OVERLAP BY HALF AND ANOTHER SINGLE PASS IN THE OPPOSING DIRECTION, KEEPING A WET EDGE ON THE OVERLAP.
The reason for the 'speckles' is improper technique. You are spraying the cans waaay too far away and you keep starting and stopping. You need to make long strokes, keep it much closer to the panel and move much faster. You gotta spray those cans like an actual spray gun...
No this is just shocking, I've never painted a car but know this is just bad technique, with the whole paint, white will hide it somewhat lol i painted a rim black an a silver one an it turned out better than this... Lol
The length of the panel and start from front to back or back to front not in the middle of panels finish a stroke stop with the psst psst psst looks good tho
the bodywork turned out really nice BUT you dont have to PRIMER the WHOLE truck?! just where bondo /fiberglass is placed at , thats what WE DID in Mister c's class
I seen a few places he missed on the second coat like the door by the glass.. besides that he wasted alot of spray and could have probably did it in 3 cans.. don't mean to critique your work but that fan being so wide smooth long back and forth not short sprays ..either way good video
Love it. Don't listen to bad comments, keep going. I have more fun doing crazy fun stuff like this. I painted my friends duster in his driveway on a bet. It came out fine and I won that bet, let me tell yah that six pack went down smooth.
You should always paint from the top down so gravity helps blend the paint with a wet line as you go. This helps reduce dry over spray which helps reduce orange peel.
@@nickcimini7233 my mistake I read that as you were the guy whiting put the murals for like a company…your the tagger😂😂 hey man my stuffs never been tagged I enjoy the art as long as it’s not on my building😂😂
@@songdogseekers Thank you, sir. Is the bolt pattern on the 5x4.5? I'm having a heck of a time trying to find 5 lug rims that'll give the Ranger a more rugged look. Any suggestions? It has a lift through the torsion bar. Any help is appreciated.
Never wear breathing protection when painting. Do not mask tire/well area. Always spray in a dry-floor environment. Only shake the can before spraying; NEVER shake during the spraying process. Smoke as many cigarettes as possible in life. Great video guys!
HAHAHAHAHAHHAHAA
We use condoms for protection!
Exactly. I'd ignore everything they say based on these things
It's not a how to video relax
@@dealerhealer3673 hush little man.
These guys make Earl Scheib look like a premium restoration shop
Roflmao
😂
The problem is he’s pushing the cap on and off way too much. You end up getting tons of solvents instead of pigments. Run the length of each panel not small areas. You can hold the cam upside down spraying for about 5 seconds to lower the pressure in the cans so the paint goes on thicker. Also never spray the first couple sprays of the can on the vehicle. Spray it at the air a couple times till it sprays pigment and not just solvent then go to the vehicle.
That was driving me crazy him not spraying the length of each panel
Well that's your problem right there, you shouldn't be painting a cam guy!!!!
Even Stevie Wonder could see the awful spray technique.
“Truck all tacked down” as he puts his oily hand all over the hood! 😂
That’s what I just saw ….
I saw that too😅😅😂😅😂😂🎉😂
Overspraying the tires, shocks & springs 🙈... ya killin me Smalls 🤯
That's what is called complete paint job
@@peter455sd earl shive paint job 😂
The Sandlot reference 👌
Don't forget the exhaust tip lol
or the dents in the tailgate and left front fender .....WTF?
Gotta love that white tailpipe, goes good with all the other white parts.
Wire harnesses,Springs and tires and rims
Really would like to see how well this paint works with proper techniques.
You're supposed to sand off the speckles. They call it orange peel.
@@roperfoerderer1594 lol no that's not the same thing, those speckles come from them holding the can too far from the vehicle. Instead of laying it on its being misted on
That's about the truth
I wouldn't trust them painting a lawn chair. Can definitely tell they have no idea how to properly paint a vehicle.
Exactly, they’re painting like a child
That was VERY painful to watch.. at least cover the tires 🤦🏻♂️ long strokes please!!!
It may take a while for me get over the FECKLESS overspray on the tires and all. Can't unsee that sloppy painting.
Great video, thanks. For anyone doing the same, it's important to wipe the nozzle at every chance, so keep a piece of cloth with you. Shake that can, alot, keep thta pressure going and work in a uniform pattern, keep following that wet line and move downwards. First coat should act like a tack, so just spray lightly and let it dry a bit, then you start spray painting.
I've been an auto body and paint man for 50 years now and I'd have to say' for what you were working with and giving credit when it's due' I would love to have you 2 guys paint all of my worst enemies vehicles.
At least it took me 32 years to make money of your retarded comment
@@songdogseekers
You want the job or not?
Make enough money from your dumb comments
@@songdogseekers
You're a hopeless hack' going through the comments proves that.
Closer and move quickly you'll get less dry spray and less oranges peel in the finish product and keep the can parallel to the panel you're getting heavy streaks in the roof
Folks you only get one set of lungs wear a respirator at all times when painting
Definitely would love to see the finished product with the rustoleum paint!, good job!.
I've found this product lays better if you soak the cans in hot water 30mins prior to using
Great job painting the small dents the tires and rims. Should wet the floor for dust and first layer light paint . Three layers micro thin paint do about 10 then let dry the sand it out then 2k clear coat it
If your going through the trouble of covering your windows, why not your tires? It’s probably easier getting over spray off the glass than the rubber.
Because they was just roller tires new rims and tires went on after
@@songdogseekers what a waste of good rubber.. way better looking than my stock rubber
A qui kwwipe w/brake fluid will clean a tire sidewall better than anything on the planet, follow up with a brush and Dawn dish soap and water .
@@jessemoss2548 when I used to work in home fire restoration I used to use a aluminum oxide oil base primer for block and metal and would not cover my face fully, as I sprayed over head ..I would look like one of the guys from "Kiss " I would use petroleum jelly/ Vaseline to wipe my eyelids and face. i was very surprised on how well it worked, and it didn't burn my skin.. I imagine that it would work on the rubber .. ...prep? Or clean? Age old dilemma
@@christhopherlasher2828 a other good secret is liquid gold furniture polish , it has a chemical that very very gently breaks down wax and paint finish for an unbelievable finish on a paint job , it is so good that after a couple minutes of massage it will take dried Bondo off your hands, also the best homegrown secret for primer and wetal prep to accept and hold paint forever is DISTILLED VINEGAR! SOLVENT AND PREPSOL ARE TOO STRONG FOR RATTLE CAN PAINT.
20 years ago I used white primer on a rusted(surface rust and original paint) on a 72 c10 I had.. looked like a $1000 paint job, lasted 10 years!!!
I've never seen anyone who didn't know you don't trigger on and off in the middle of a panel.
Hell yea ,, Thanks my Brothers for posting this video ... Im going to try spaying my camper shell you guys kick ass 👍👍👍👍
Being a retired Automotive refinisher this was almost physically painful to watch
Some times the new guys have to learn the hard way. I have a hard time watching them overspray the the glass, wheels, chrome, door handles and key holes. Also little or no prep...😖😖😖😵💫😵💫😵💫😵💫😬😬😬😈
Did this to an old work truck that was originally orange. We decided to go black to cover easily.
We painted the truck in two phases. A couple of days before doing the large panels we used normal cans of black to do the door jams, gas filler, under hood and misc. areas. We also lifted the truck up and shot on three coats on the very bottom of all the panels where it would be hard to reach once the truck was on the ground. We let that cure for a few days then painted the large panels.
What we learned was those large paint cans really liked to be warmed up before spraying. We bought 8 cans and set them in a two buckets of hot water for about 30 mins before painting the large panels. Each can was then shaken for about 5 mins. right before spraying and again about every minute. While I was spraying my buddy was shaking the next can. When ready to paint the cans were very warm but not uncomfortable to hold.
First coat was a mist coat that we let tack for 10 mins. Second and third coats were full wet coats. It took me about 10 mins. to do the entire truck then we let that sit for about 20 mins. before starting on the next coat. After three coats the truck looked good and the paint was nice and smooth.
After 2 yrs. it still looks good. We do normal washes and hit it with a spray wax a couple times a year but that is it for maintenance. Just wish they had more colors in those large cans.
Did you clear it afterwards
Thanks
Man u start from roof 😳 then all the corners and a light coat 😳
🤣🤣🤣 this video is like watching some child's playing whit paint 🎨
Woah man 😯😯😯😯😯😯😯😯😯😯😯 that's crazy bro it's almost like he just painted it😯😯😯😯 with a rattle can for cheap 😯😯😯☺️☺️☺️☺️😂😓😅😊😊🤔🍇😯😩💛😤
Thanks for the input like I CLEARLY said in the video this was my first time painting a vehicle! Next time I’ll look you up and you can come paint it thanks for the Adsense
@@songdogseekers I'm not hating just trying to help I recommend putting a guide coat down then Sanding it with a block water and in a x motion then letting your cans still in boiling water for around 20minutes to build pressure in the can and make it spray Better
Putting the cans in hot water helps. How'd it turn out with the clear? What clear did you use? I can't find the final video
Let me start by saying I appreciate the content, nonetheless.... painting cars or not, ya'lls technique is atrocious. There are so many grievous errors made, like not testing a new can on a piece of cardboard before spraying, multiple overlapping passes on a single section of a panel instead of lighter consistent singular passes on the whole panel, not constantly shaking the can during the the spraying, not maintaining a constant even distance from the work piece, starting to spray directly on the panel instead of off the edge and coming into the panel... and just fyi, ya'll did like 10 coats, not 2. When you go over the same area 5 times in a single spray, that's 5 coats. Your end result could have been so much better.
They were going for the Mickey Mouse look. Don't worry. The job will need to be redone in 2 years.
It’s a work truck not a show truck thanks for the Adsense
@@songdogseekers even if it’s a work truck, you went through the trouble of buying supplies and filming the process. Have a little more pride in your work and stop using the excuse that it’s “a work truck.”
Well said , Couldn’t have said it better myself!
Oh me gott! Just leave it be. I enjoyed the video. So much negativity. It’s not your project.
Before painting did you guys sand and primer first? If so can you go into a little detail on the sanding technique and the primer used plz
I assume you don’t mind having white tires as well
Look good !
Where did you get your white paint? I’ve been looking everywhere but they only have black
Hey guys good job everyone who’s talking crap are over the internet creeps you guys did good I don’t think they realize this is spray cans not a professional 8 thousand or 5 paint job keep it up man
Thank you
Thank you for this video.
Your very welcome thank you for watching
For a work truck it looks pretty good to me. Is that the factory sprayer that comes on it. I just got a Chevy S10 that I'm going to paint and I'm thinking about using this.
Yes that’s the factory sprayer
where you buy the spray paint -- i check Amazon -- did not see anything close to what you use. Ty
What kind of primer did you used, because I an seriously wanting to do my car? Please respond....
After the second coat was there still orange peel or it went away ?
I redid my Izsus NPR using the white. I waited a week and put 2k over it. It looks way better than the factory. It had 100’s of small rust spots and after 3 -4 years it has zero rust. I should probably finish it and do the 2 doors. I hate painting.
How has this held up? Thanks
As a former bodyshop painter I can do this the Way it should look
( EXPERIENCE , KNOW MY SKILLS OF PAINTING WITH SPRAY GUN SO A CAN SHOULDN'T BE TO DEFAULT FOR ME most important the skill of spaying left to right correctly... ) not bad for a first timer 👍
Thank you!
lol not bad? It was brutally awful, remind me not to call you to paint my kids tricycle
Guys!!you don't know how much you have helped me.in my country,painting a simple small car goes as much as 350$ and that does not make it shine .i never knew there is good quality pressurelized paint out there.After painting,Do i need to use polisher for shinning?Love from kenya.
Yes you can wet sand it with a 1500 2000 and then polish it
I did the 50 dollar paint job with Rusto and it didn’t last long but it was outside in all weather, but it did look great for a couple of years and it was a roll on not spray 8 coats and lots of sanding , and why only white and black paint how’s about some colors
So, is it just the spray can nozzle that makes this work good, or does this can have also more pressure as well???? Because if it's just the spray nozzle, couldn't you use any paint can with the same nozzle?!??
Actually, I thought the same thing and tried it on a conventional spray can. Turns out the turbo spray can nozzle only fits that specific turbo can. I ended up painting my index finger due to the spray escaping out of the bottom of the nozzle! Too bad cause it's a killer 10"-12" fan spray nozzle... Gotta come up with a way to adapt it to a conventional can🤔
This was the video I was looking for cause I plan on getting a obs power stroke an I want to paint it all white
Has held up great!
wow a professssionalll painter he is
Question- was the white you were glossing over with turbo can, was that white a white primer from a can or was it white paint from a can? Thanks, great video!!!
Just subbed !
Why did you spray the tires?
What did it looked like? Prep looked week done
Mr. B. Here ! 🍩☕️👀😎👍 looks fine for what it is , a truck for work and not a show truck ! LOL !
Where should we buy that product?
You're getting speckles because you're letting off the trigger while you're over the surface. It will spit paint when you go off and on over the surface.
I can't wait to do this.
No it's cause he's too far
Love the backyard techniques 😅😅😅😅😅
The amount of overspray is making my palms sweat
True dat ! I just did an88f-350, Ford blue and decided to mask and paint 1lpanel at a time due to my limited ability exhaust fan sumbich shines like a hounds tooth , I went extra wet to get my shine , and will rework several small runs as it cures. Gowey and shine , cleaning up a few runs on a beautiful shine is more of a worksaver that being shy with your rattle can and getting stuck having to buff out a whole vehicle for a shine.
Watching the guy rattle can is giving me heartburn.
Hey kids make sure you never ever wear a mask when spraying paint or chemicals
You still might have to color or wet sand it before clearing it if you want it to look really good
It will take a lot more than that to make it look good.
Did Ron Jeremy give rustoleum the measurements for that paint can?
Put your cans on a bucket of hot water before hand . 2 to 3 light coats then a heavy one spraying 15 min a part .
Thank you! I’ll do that next time
It's not the can,it's the way he triggers so much cause build up on the tip of the nozzle! This pguy paints like an 8 year old🤣
@@robinsonbernabe3925 yo
To eliminate overspray one should start closest to you and move further away.
A few good coats and real fine water sand and then a couple good coats of clear and would probably look pretty good
What lift do you have ?
Can you still smell the paint through the ventilator
I wonder what would it look like with people who know how to paint…
Looks great to me! That’s all that matters thanks for the Adsense
@@songdogseekers
Your welcome! Waiting for the next video!!
in this case it was not the paint, it is the painter.
my thoughts exactly... it's like they've never watched a single video on how to paint a car lol. Cutting each panel intro quadrants, and putting on nearly full coverage on the first pass... ffs. LONG, SINGLE PASS ALONG THE WHOLE PANEL, THEN OVERLAP BY HALF AND ANOTHER SINGLE PASS IN THE OPPOSING DIRECTION, KEEPING A WET EDGE ON THE OVERLAP.
Thanks for the Adsense
The width of the spray pattern reminds me of spray on contact adhesive cans.
Nice
How many cans did you buy or use, to spray the pick up ?
5
The reason for the 'speckles' is improper technique. You are spraying the cans waaay too far away and you keep starting and stopping. You need to make long strokes, keep it much closer to the panel and move much faster. You gotta spray those cans like an actual spray gun...
Omg my OCD is in flames rn watchin this guy paint lol gahhhhhleeee 😩😂😂😅
Gotta love them kids.
I'm looking to use this product temporarily for my project car
Worked great been running the truck for a 7 or 8 months
Bravo!
Why so many haters, these hillbillies know how “ta paint”
No this is just shocking, I've never painted a car but know this is just bad technique, with the whole paint, white will hide it somewhat lol i painted a rim black an a silver one an it turned out better than this... Lol
Looks good to me
Can we see a Video of cleaning the overspray out of the knobs on the all terrains after? 😅😅😅
Pretty simple just do burnouts in a puddle of solvent
The length of the panel and start from front to back or back to front not in the middle of panels finish a stroke stop with the psst psst psst looks good tho
the bodywork turned out really nice BUT you dont have to PRIMER the WHOLE truck?! just where bondo /fiberglass is placed at , thats what WE DID in Mister c's class
When your painting you always start from the top and work your way down overlap 50%.
From what I can see on the fan the very top and bottom of the fan is coming out way thicker than the middle
Painted dump truck with a gallon of rustolium with harder lasted 6 years so far
Respirators are to new looking ,,first time using one lol 😆
On top of all the other Mack and Meyer moves they painted right over the rust and dents!
Outstanding!😂😂😂
I seen a few places he missed on the second coat like the door by the glass.. besides that he wasted alot of spray and could have probably did it in 3 cans.. don't mean to critique your work but that fan being so wide smooth long back and forth not short sprays ..either way good video
Is this the first time using a spray can?
Stopping and starting the spray in the middle of the panel seems like the wrong way to do it.
Probably would have been better if ya got someone that knows how to use a can of spray paint
Ya like 6 year old
What did you clean it with?
I used mineral spirits with a microfiber rag
Love it. Don't listen to bad comments, keep going. I have more fun doing crazy fun stuff like this. I painted my friends duster in his driveway on a bet. It came out fine and I won that bet, let me tell yah that six pack went down smooth.
Did you sand after primer?
Yes
It would help if you started painting from the bottom to the top so theres not overspray
Thank you
He missed so many spots on the rear of the bed it was driving me nuts.
Yes but I got them as I said it was my first time painting next time I’ll message you to come paint it for me for free thanks for the adsense
You should always paint from the top down so gravity helps blend the paint with a wet line as you go. This helps reduce dry over spray which helps reduce orange peel.
One says paint bottom to top and the other guy says top to bottom lol
Should of done it in bright Orange save all the sanding after😂
“How NOT to paint Ford Ranger with Rustoleum Turbo Spray Paint” There, fixed the title for you. 😂
Ewww these comments are rough!
I think it looks great.
End result looks pretty good.
Thank you that’s what I thought no show truck! and yes they are but you have that with key board warriors
Eu gosto muito de pintura com esprei
Warming the cans in hot water before spraying will reduce (not eliminate) orange peel.
Not bad👍👍👍👍👍👍👍
U gotta warm the bottle up so it don’t leave orange peel put in hot water
I’m surprised you guys didn’t tape off the tires as well & remove the door handles & tailgate handle.
Well stop spraying like your tagging a wall under a bridge and it won’t be spotty🤷🏻♂️😂
😂 bests comment!
No, I used to paint walls under bridges and this man has zero can control. The walls I painted came out better than this...
@@nickcimini7233 😂😂 yeah graffiti artist real are pretty amazing from an art standpoint…the whole damaging property thing meh 😂
Keyword...." used" to....
@@nickcimini7233 my mistake I read that as you were the guy whiting put the murals for like a company…your the tagger😂😂 hey man my stuffs never been tagged I enjoy the art as long as it’s not on my building😂😂
What size are those tires on the "rustoleum" truck?
35/12.50/15
@@songdogseekers Thank you, sir. Is the bolt pattern on the 5x4.5? I'm having a heck of a time trying to find 5 lug rims that'll give the Ranger a more rugged look. Any suggestions? It has a lift through the torsion bar. Any help is appreciated.
35 inch white walls
Give us a video showing the condition one year later.
I love it. Did my whole car in Tremclad/rustoleum yellow. Wish we had the turbo cans here.