The Vacuum Cleaner Cannot Be Turned On - How To Repair Electrolux UltraFlex UFFLEXA
Vložit
- čas přidán 8. 09. 2024
- Disassembling & repair of vacuum cleaner Ultra Flex UFFLEXA. Vacuum cleaner doesn’t work / can’t be turned on. How to check / detect a vacuum cleaner defect, faulty power micro switch - easy to replace it with new 4pin switch.
Model of vacuum cleaner: Electrolux UltraFlex UFFLEXA
Part Number: 1181968031 (switch board)
www.proexservi...
www.proex.sk/
#diy #how #disassembly #assembly #vacuumcleaner #repair #electrolux #microswitch #replacement
J'avais le même problème, qui est résolu.
Merci de m'avoir fait gagner du temps !
Je vous en prie 🛠️👍
Merci pour votre explication ,j'ai en effet tiré a fond le cordon,mais pas concluant puis réessayer a plusieurs reprises et ,hop,,et bien il s'est de nouveau enroulé ,et il semble que tout s'est remis en place ..merci
totally nice handling and great video , good job mate ,
Loved the video i have the same hoover, i have a faulty speed controller. 3x repaired the same issue. 4 th time no longer hase the garanee 😢
Thanks 👍
Faulty? Broken regulator or what?
bonjour ,merci pour le tuto,cependant ,moi j'aimerai avoir le même pour le cable qui ne s'enroule plus .Je pense que le démontage est le même, mais comment réparer ensuite? Merci
Bonjour, oui le démontage c'est quasiment pareil, s'il coince alors il faut le dérouler et le rembobiner. Si le mécanisme est faible/mauvais, le remplacement de l'ensemble de l'enrouleur de cordon est la seule option
Eng: Hello, yes, disassembly is almost the same, if cable is stuck then you have to unwind it and rewind it. If mechanism is weak/bad then only option is the replacement of entire cord winder 🤔
Hi,
I have exactly same problem. What is called the part you replaced?
Thanks
Hi, push button 4pin, or micro switch
Thank you
How exactly do i find this push button.
I have exactly same hoover with exact same problem
Hi, you can replace it with new 4pin switch (soldering is needed).
Or just replace spare part, look for Part Number: 1181968031 (switch board)
Thank-you fornquick response. I opened and saw button itself is fine but the plastic push part that presses push button is broken. Tried to glue it but it wont hold
If you have same model, then plastic button is 8090099022
Unfortunately in my case the 4pin push button itself is fine but the plastic mechanical push buttons part that presses actual push button is broken n. Dnt see what could be possible solution
Then you need to replace it, spare part (plastic button on/off) is 8090099022 (if you have same model: UFFLEXA or similar)
I have the same model, I knocked the back after a filter clean to loosed any dust and all of a sudden the suction is now at like 5% .. no idea what I messed up..
Did you try it without dust container?
Those 2 hoses (silver/gray - right next to container) have to be on right places, not vice versa (check their seals).
How can I replace vacuum cleaner motor for Z1670
Hello, I am not sure that you have correct model, do you have Product number?
Motor for PC1670 is no longer available, you have to pry out on/off and winder buttons and there are screws, then you should be able to open motor holder.
I failed to turn the catch! 🥵
Hi, try to put flat screwdriver between vacuum body and that silver ring (from top left - if you are looking from front on that ring, it is on 10 o’clock), pry that silver plastic with left hand, with long pliers hold silver ring on 7 o’clock and push it down (you have to stand over top of the vacuum cleaner, so you can use your weight and vacuum cleaner will stay on place, you dont need 3rd hand and you can push it harder) - by this way you will probably scratch this silver ring with pliers but it will be on bottom of that ring, so it doesnt matter, i think 🫣
Bollocks to that. Just buy a new one.
That 4pin switch cost few cents, or few euros if you buy whole switch unit 🥲