Mercedes w201 190e 2.0 32 year old car fuel pump change
Vložit
- čas přidán 7. 09. 2024
- Hi there all, I wasn't gona make a video of this until I realized that I should but by then I already removed the pump so in this vid am re fitting the pump, but removing it is basically the opposite and its not to hard on this car.
Make sure the battery is disconnected and you wear protective clothing in case any fuel gets spilt on your skin.
#mercedes #190e #w201
Had 190e for many years, best car so far
Lovely car for sure.
Very good. Greetings from Norway.
Thank you very much! greetings..
Thanks you so much for your video! I'm from France and you help me with this tutorial. 😉😉😉
You're welcome 😊
Hi, I have a 1988 2.6. The buzzing sound from the fuel pumps is a bit erratic. Now the car randomly cuts out. I have changed the Fuel Pump Relay and the fuel pumps were changed about two years ago with Bosch ones.
I’m told it could be the fuel pumps again or the crankshaft position sensor.
Any ideas?
Many thanks,
Irfan.
🤔 is this the relay you changed ? There is another relay that can cause issues. czcams.com/video/Dh4ZctocPF8/video.html
If your car has a distributor then there is no crankshaft sensor that can cause cutting out issues. If there is no distributor then yes there could be a problem with the sensor. Or it could be cutting out for other reasons.
God job m8
Thanks.
Got the 190e 2.6 from 91, has 2 fuel pumps, it can run on 1,i found out
Oh really that’s good
It will only take a wire, but it will cost a lot at a work shop
I can imagine, labour cost are expensive, and so are the parts.
Hello friend, I have a problem, I already changed the fuel pump and it does not turn on, and the problem is also not the relay because it works and even so the fuel pump does not show any sign of life, what could it be? Can you point me to something I can do? Big regards!! 🤜🤛
May I just ask, how do you know the relay is working properly, just because mine was intermittently working and failing hehehe. how ever if you pins 30 and 87 of the relay it will bypass the relay check out this vid minute czcams.com/video/Dh4ZctocPF8/video.html 6:05 if you connect a wire between those two pins and refit the relay then ignition on either the pump will work or it wont, if it doesn't check all you fuses. do you have an immobilizer fitted by any chance ?
The plus wire has gone, so did it in my 190e 2.6
The relay pin 87 is for the fuel pumps, the 2.6 Has 2
It allso goes to the aircondition and the warning lights
So i had 2 rewire it
How match BAR have the fuell pomp?. Is it 6.5 BAR ! My car is 2.0 w201 1989. I hope sumbody can anser my quation. Greets frome holland. Bye
Hi mine was a 5 bar, i think the 6.5 bar goes on the 6 cylinder engines
And only a Mercedes person can fix it
Ohhh mercedes only, didn’t read that.
Hi, why my car has double? Should i charge dem both
Double fuel pump ? Well if it has and both are faulty then may be you have to change it.
@@DaringBeefcake thanks 🙏, how can I find out one of them or both dose not work? ✌️🙏
The wire to the pumps broke down, so i had 2 buy 2 new pumps and a filter,
Oh I see, better change them I guess.
Takes some time
Yes lots of time.
By the way god bless you m8
@@ap6878 thank you God bless you too..
The plus wire
Was not good.
The rubber bands around the fuel pumps were gone
These are so old now, new parts are required.
Hi, is this a diesel engine?
Sorry, I know. 190e
2.0 petrol :) no worries 😉
Diesel cars dont actually have fuel pumps like this. Pressure is what makes diesel explode. They have a pump right on the engine block
What is the part next to filter on right?
Pressure regulator, excess fuel pressure is returned to the tank
I think the regulator is in the engine bay, the one next to the filter is an accumulator, keeps the pressure in place after switching off the engine, so it can then be started faster, though pressure reduces with time, it can be measured with a fuel pressure gauge. ive been doing some research heheheh...
The pumps are a mess,
That’s not good
About 300 dollars
Will you fixed it yourself.
So i used strips
Strips for what ?
To hold the fuel pumps and filter
The rubber bands were gone
@@ap6878 oh ok..
@@ap6878 yes all that area gets deteriorated.
It burned both pumps
Oh I see, may be the old pumps drawing to much current.
No fuel...
No fuel no start