How To Install Wainscoting / Picture Frame Panelling To Hall Stair Landing - Easy Step By Step Guide
Vložit
- čas přidán 22. 07. 2024
- How To Install Wainscoting / Picture Frame Moulding To Hall Stair Landing - Easy Step By Step Guide
00:00 Intro
00:52 How To Mark Spacings For Wainscoting
01:45 How To Calculate Panel Sizes On Flat Walls
02:45 How To Pull Chalk Lines For Wainscoting
06:22 How To Cut Mouldings For Flat Areas
08:34 How To Assemble Moulding Panels With Mitre Bond
10:51 How To Fix Moulding Panels To Your Wall
13:49 How To Cut Wainscoting To Fit External Corners
16:58 How To Fit Wainscoting Up A Step
22:37 How To Fit Wainscoting Up A Staircase
How To Install Wainscoting / Picture Frame Moulding To Hall Stair Landing - Easy Step By Step Guide
In this video we are installing wainscoting / picture frame moulding to our hallway, staircase and landing.
This is an easy step by step guide for all DIYers.
All hall, stair, landings are different and we will show you how to calculate and measure the height, mark chalk lines and the how to install wainscoting / picture frame moulding to straight walls as how to cut different angles for internal, external corners and angled joins that you get in a hallway and up a staircase.
We will demonstrate how to easily calculate the angles required for your wainscoting / picture frame moulding and how to fix it to the wall.
Renovate your staircase and hallways with wainscoting!
Astragal Panel Moulding provided by @SkirtingWorld
_______________________________________________________________________
Tools Required;
Angle Finder: amzn.to/3wwg1mT
Chalk Line: amzn.to/3R7EgS7
Tape Measure: amzn.to/3j9nQfq
Pencil: amzn.to/3HBBmC4
Level: amzn.to/3kKVloN
Adhesive: amzn.to/407Y7ok
_______________________________________________________________________
Please like and subscribe to The Home Improvements Channel UK
MORE VIDEOS FROM THE HOME IMPROVEMENTS CHANNEL:
How To Install Dado/Chair Rail To Hall Stair Landing - Easy Step By Step Guide;
• How To Install Dado/Ch...
HOW TO INSTALL WALL PANELLING TO STAIRS - EASY STEP BY STEP;
• HOW TO INSTALL WALL PA...
How to Fit Stair Carpet Runner with Underlay & Grippers;
• How to Fit Stair Carpe...
How To Install Skirting Boards (Baseboards) | DIY GUIDE
• How To Install Skirtin...
________________________________________________________________________
Instagram - thehomeimpr...
Facebook - / thehomeimprovementscha...
TikTok - / thehomeimprovementsuk
Shop - www.amazon.co.uk/shop/thehome...
Email - diyukhomeimprovement@gmail.com
________________________________________________________________________
Thank you for watching The Home Improvements Channel UK.
Disclaimer:
The content provided by The Home Improvements Channel UK is for informational, educational, & entertainment purposes only and some projects and tools may not be appropriate for all skill levels.
This is a guide only and The Home Improvements Channel UK cannot be held liable for any work undertaken or damages caused.
#diy #homeimprovement #howto #stairs #decor #renovation #tips #carpentry #wainscoting #pictureframing #hallway - Jak na to + styl
Spent the past few days doing our stairs/hallway and really happy with it. Never done any panelling before so tackling crazy angles/curves was a bit daunting! Your video was fab and helped so much. Thanks for sharing 😊
That is awesome!
One suggestion I would make. When cutting your mitres with many the same size it’s much easier to set up a stop block away from your blade and this ensures they are all the same size and it’s much quicker.
This is the best guide for panelling on CZcams - Thanks so much!!!
Glad you think so!
I love it how you did the divide gap, that's thats most important thing
Great video, you explain everything in detail and easy to understand!
Brilliant Video, super instructional and enjoyable to watch. You made a great job of that panelling. Love the channel, keep up the great work.
Love this video! Great tips!
Great tutorial. I'm glad I came across your video. I can't believe you made d.iy look like so much friggy fun 😅😅😅. The chalk line thing was a great idea, I've never seen that before. Nice job, and many thanks 😊
Thanks 😁👏🏼👏🏼
Yes I was thinking the same specially with the chalk line the way you make it Ping 😂 it’s like pulling on some nipples
Excellent video as always lads, thanks
Great video guys ... with my hallway wall its would start at the front door and leads all the way up the stairs finishing at the bathroom door. When working out the number of panels would it be best to take the complete measurement or can i break it down into sections? ie door to bottom of the stairs, bottom of stairs to top etc. I would obviously like it all to look uniform so your expertise would be appreciated.
Hi, great video, very helpful. im using a friends nail gun to save money, i will need to buy the pins, though. What size would you say i should use for the dado rail and the rhin panels? Appreciate the help.
Cracking video, thanks guys, going to tackle our staircase now! 😃🥶
Good luck!! 😊
Great video 👍🏼
How would you figure out how much panel moulding you need for job like this?
Also if the dado rail is higher than the handrail on the stairs, how would you terminate the dado on a landing where the dado would finish at the banister? If that makes sense 😬🙈
Thankyou
What size pins would you use if pinning 15mm thick beading to a brick and plaster wall ?
What would you suggest if there is a radiator on the wall where you want your panelling?
MY drywall has all kinds of texture , poping nails and seam lines. Im not sure doing this wainscoting will look good over a non smooth surface. Any suggestions? Floating drywall, apply wallpaper first, ?
Great video guys, keep it coming!
Thank you
Love this , would you come do this on my hall stairs and landing please😂👍😍
Great series of vids content n presentation very enjoyable and informative
Thanks 😊
Did your nail gun nails go into a brick wall, if so what is the nail gun and type of nails, thanks M / Your Videos are more entertaining than other people's channels
Hey guys, could you do a video on vertical wooden wall slats sometime, as in feature wall, thanks
spot on lads, nice job.....👍👌👌👌👌
Nice one 😁💪🏼
Brilliant video.👍🏻
What is the name of the glue what you are using to assemble the moulding please? Thanks 😊
Thank you for cutting out all of the jargon almost convinced myself I can do some of these jobs now. How achievable would swapping stair rails etc from 60/70’s vertical style to traditional spindles etc??
Full oak staircase build coming up so should cover a lot of it 😊
How do you do measure a whole passage and stair case
Thank you, great video, helped alot! A quick question. I have a landing that is a 90 deg corner and from there the stairs goes up at a different angle. How do I make the trim join perfectly at that corner. tia
Thanks will try to make a video soon it’s hard to explain 😊😊
Best tutorial on YT. Would you recommend a specific paint covering both walls and mouldings or would wall paint suffice?
Thanks just wall paint on ours no issues 😊
It's not covered in this video but I think a video on how to cut the mitres on the mouldings would help a lot.
I’m confused, it was in the video 🤷🏻♀️
No it wasn't, you need to make a jig at a 45 degree angle, that needs clamping to your mitre saw, because most saws only cut between 45 and 90.@@selinabella8606
Great video - thanks! A quick question, if you can't use pins to hold in the panels because it's soft brick for example, what can you do instead? Would it work to use more sh*t glue with i.e. masking tape to protect the wall from the excess that squeezes out?
Could work these walls are brick and will take a panel pin until the glue sets then remove it 😁👌🏼
What is the appropriate height for the baguette above the Panels?
Great video, best I seen so far. Bit of advise..my wall in some places is slightly bumpy, uneven plaster work,would panelling still work ..how would you tackle this issue? Thank you
Ps: i am diy ..what saw size would you recommend for this work.Thx
Thanks Anna and caulk the gaps after your done 😊 a small mitre saw will be fine don’t need anything big 😁
Great easy to follow tutorial!! Thank you so much!
Thanks 😁😁
Great tips guys. I when it’s on 22.29 how did you get the the flat section in the top point of the panel, I’ve recently done some and struggled to get cuts my chop saw it maxes out at 60 degrees. Cheers lads
You cut a scrap at 45 clamp that to your saw you then have a starting point of 45 degrees hope that helps 😊
Dividing lengths into even marks is wayyy easier with metric
What size pins did you use?
Love it
👏🏼👏🏼👏🏼
One side of our hallway has a couple of doors so some of the walls in between the doors are not very wide so using the same spacing as the opposite wall would look really odd as we would have one of the panels extremely thin. Might look odd to leave them out as it wouldn’t flow up the stairs
Yh you can adjust as you see fit to get what looks best for your space 😁 that’s why it’s always best to chalk it out first
Hi great job and great video. What glue do you use to stick the corners of the picture frames together?
Ctec super fast 😊
Great video chaps! Silly question incoming - if there is approx a 10mmdifference across between where the top / bottom of the panels will be over the space of a wall (2m) because it's an old / uneven house, do I need to do anything different to account for this? I'd be looking to do 2x panels with the same gaps as you've done. Will this much of a difference matter?
Chalk it out chances are it won’t be visible to the eye 😊😊😊
@@homeimprovements Nice one, appreciate it! :)
your acting skills are great too :D
Thanks! 😄
When you said "make sure it's pressed in", you pressed it in and it moved... genuine question, if only using 4 pins, how do you go about getting the profiles properly flat against the wall?
The grab adhesive does 99% of the work the pins are mainly to stop it sliding 😊
Hi, i have a large curved section at the top of the stairs.... can you give any more advice or help with tackling the curve?
If we get a chance we will 😁
Can you please do a video showing how to bend gripper metal around a vinyl entry way?
Will try 😊👍🏼
Thank you so much for this video!!!! Quick question (and perhaps a stupid one). When you apply the panels vertically up the stairs, should every single one be the same length? My calculations are suggesting that the panels will increase in length as they go up the stairs, but I can't work out why. Any advice pls?
No stupid questions 😁 so if measured horizontally level they should be the same they won’t measure the same when measured at the angle of the staircase . Hope that helps 😊
@@homeimprovements okay will try that and let you know how it goes. Thank you so much!!! Do you have an IG account? Would love to follow you there
We do it’s the same name and logo 😁💪🏼
thanks for the video, the wife wants this now...the only bit i may do differently is under the window ledge, rather than have it meet the underside i'd probably have the 100mm gap...not sure though until I see it, might look odd
Thanks 😊 and Yh it’s all personal preference another reason it’s great to chalk the design first 😁👌🏼
How do I do the stair calculation if I have ready made panel kits that are pre-cut to 45 degrees, can I just saw the correct angle and make them slightly smaller?
Not too sure what your saying there mate ?
@@homeimprovements I bought these pre cut panelling kits from b&q mate and they’re designed for a flat wall… would I be able to use them for the staircase too ?
Ahhh you’d need to recut all the mitres 😊👍🏼
Hi, first of all your video has allowed me to attempt panelling my whole hallway all the way to the loft!
But I need some help - what if the angle is 42 and the calculation answer is 69?!?
Great not sure what your asking there tho 🧐
Legendary champions
no sound
How long would a project like this usually take you guys to complete 👍
A day to get that done longer when we are filming tho 🙈
Is there a profile name for the beading used for panels please
Ogee 😊
Thank you
Hi, what is the name of the material your using ??
Mdf ?
My angle is 46 degrees so minus 180 divided by 2 is 67 degrees how do I cut this?
We have a short show how to create a jig for those cuts 😊
Where’s the show lol
@@homeimprovements given up looking for it lol
It’s all well and good but I can tell this is probably your first time doing this. You need to learn how to size the boxes. The end result would look so much better!
Do you mean how to decide how many you should have? Do share!
@@lindsay_dee
Yes, you’re correct. You find the smallest wall in the room first, this will give you the relative size. Wall sections that will have multiple panels should be broken into odd numbers of panels. Three or five panels will have a more elegant appearance than two or four, for the same given wall section.
Magic - thank you!! Big help
@@lindsay_dee
You’re very welcome! Let me know if there’s anything else I can help you with!
@davidcerce Thanks for the tip. I'm researching doing this, and haven't seen this mentioned anywhere, but it seems obvious now you've said it.
Lads im pulling my hair out.. ive got a 45 degree angle on the one of the stairs, how do i get it to join? Can i send you a pic somehow? 😂
Gonna make a video on it mate had a lot asking but simply put you need to level of turn then go back down
Hey can y’all add closed captioning to this video please
Lol
That's what the transcript for 😊 🇬🇧
Think I’m in love with you 2❤
Thanks for the support 😊🔥
Just for you, might be good to switch your audio to mono as it keeps going left to right :)
We’ve since updated our audio it was an issue with the mics thanks for the heads up tho 😊😊
My right ear is lonely
Get rid of the music
Thanks for the tip, hope you have a good day 😊
It needs setting out better you would not have a panel on the flat and going upstairs