Good video I have a question will the foxwell NT614 could program a swap Ecu . I been having trouble with the transmission not shifting staying in 3rd gear I change all the solenoids cuz it was reading bad solenoids so I ended up changing them all but same problem so I bought an ecu from a junkyard i wanna swapped it but will need to program it will this foxwell NT614 do the job ?
Hi its me car fault You need to short out 2 pins at obd Port for 30 minutes while ignition in run mode search on google you will found how to program immobilizer on old toyota
Thanks for the video. I have a question though. It says "Requires road test to relearn values", does it mean we drive as usual after reset or is there any specific procedure for doing the road test after the memory reset?
Yes you need to drive in stop start pattern for example start driving untill all gears shift then stop then start over again also let gears shifting on different RPM'S on each start
@@CarFaults Thanks, this is only to test the transmission after the reset or it is necessary that this need to be done? What happens if I simply driving after the reset? Also how to let gears shifting on different RPM's on each start?
@@kclreddy if you drive simply ECU unable to relearn upshift and downshift ECU keep relearning for around 15 minutes. For shifting gears on different RPM'S let upshift around 1500 rpm by less accelerating then let around 2500 rpm so on
I have a 2013 nissan rogue, I just replaced the step motor on the valve body. Now the vehicle doesn't drive right. It barely has any umpph to move in reverse. It says online anytime you do work on the valve body you need to reset or reprogram the tcm and transmission. Will this work for it?
@@justtrue8228 my main question does this have transmission relearning software? I know some do and some don't. I heard this one has the transmission shifting relearn software in it. But when researching it I don't see that it does. I get mixed results online. The site itself doesn't give me much information. But I decided to go ahead and order one. I just gotta go pick it up later when I have access to our other vehicle.
@@CarFaults I have a question. I had replaced the 1, 2, 3, and 4 shift selenoid, and the transmission control selenoid in the engine bay, but my car still shifts a bit late and the d4 light starts blinking after I try accelerating. I'm guessing maybe I need to reset my cars computer, do I need to have the transmission reprogrammed sense I replaced all the selenoids ?
@@justtrue8228 I have an accord 2000excoupe. Once I shift from park to reverse, you won't feel the car actually shift gears until like 2 seconds. So it'll slip then shift. When I switch from reverse to D4 D3 D2 or D1, the car doesn't really shift slow, it kinda catches it fast enough, but the thing is when I accelerate up to about 10mph or more then let go the gas pedal it feels like the car isn't upshifting for me and the transmission kind of makes a small small jerk, & the D4 light starts flashing with the check engine being brought up. This started happening after most of the transmission fluid spilled on the floor due to a bolt that I didn't tighten all the way. Of course I put more fluid in it, the red Volvo ATF one that's says its compatible for toyota and Honda vehicles. Just mind you, i havnt deleted any codes after replacing those parts. If you know anything about this it will help🙏🏼
@@BobiPhettOfficial don't waste more money on it you already need to replace this transmission or rebuild it if torque converter and oil pump in good condition
Now there is other tool I review this is old check video XTool D9S PRO: The Ultimate Review Updated Version of D9 Pro czcams.com/video/Rhwy0hClhkQ/video.html
How do you fix C221500 error code on Mercedes w204 c350 m
how about keyprogramming sir ..i dont have that app on my foxwekk nt809ts
Which model Foxwell is in the video??? This is very important. Not all Foxwell models can do the transmission reset or programming.
Foxwell nt909
How long does it take to reset the vlp?
Is this foxwell nt710 ?
Saludos! Puede hacer otro video, haciendo un aprendizaje de transmisión automática que no sea CVT .. Se lo agradecería
I will do nissan or toyota cvt if possible!
Good video I have a question will the foxwell NT614 could program a swap Ecu . I been having trouble with the transmission not shifting staying in 3rd gear I change all the solenoids cuz it was reading bad solenoids so I ended up changing them all but same problem so I bought an ecu from a junkyard i wanna swapped it but will need to program it will this foxwell NT614 do the job ?
Which car model it is??
@@CarFaults 2007 is250 Lexus
Hi its me car fault You need to short out 2 pins at obd Port for 30 minutes while ignition in run mode search on google you will found how to program immobilizer on old toyota
Do you know if the FOXWELL GT75 can reprogram the footwell module on a mini Cooper
I don’t think so
Does fixwell GT 65 do ECU reprogramming too? I have to replace the the computer in Honda Accord 08 .
You need immobilizer programming 2008 should be supported
Hi Any dubai avalible reparing garage to reset my camry 2012
Thanks for the video. I have a question though. It says "Requires road test to relearn values", does it mean we drive as usual after reset or is there any specific procedure for doing the road test after the memory reset?
Yes you need to drive in stop start pattern for example start driving untill all gears shift then stop then start over again also let gears shifting on different RPM'S on each start
@@CarFaults Thanks, this is only to test the transmission after the reset or it is necessary that this need to be done? What happens if I simply driving after the reset?
Also how to let gears shifting on different RPM's on each start?
@@kclreddy if you drive simply ECU unable to relearn upshift and downshift ECU keep relearning for around 15 minutes. For shifting gears on different RPM'S let upshift around 1500 rpm by less accelerating then let around 2500 rpm so on
@@justtrue8228 Thanks, I have automatic transmission. I may not be able to do this. Is this road test applicable only for Manual transmission cars?
@@kclreddy only for automatic transmission not for manual transmission
I have a 2013 nissan rogue, I just replaced the step motor on the valve body. Now the vehicle doesn't drive right. It barely has any umpph to move in reverse. It says online anytime you do work on the valve body you need to reset or reprogram the tcm and transmission. Will this work for it?
For Nissan cvt yes you need almost three type of calibration depend on model
@@CarFaults yes it will work? I'm confused
@@kingdon9690 well we can't predict anything
@@justtrue8228 my main question does this have transmission relearning software? I know some do and some don't. I heard this one has the transmission shifting relearn software in it. But when researching it I don't see that it does. I get mixed results online. The site itself doesn't give me much information. But I decided to go ahead and order one. I just gotta go pick it up later when I have access to our other vehicle.
@@kingdon9690 go with autel tools much batter
Puedes hacer un video rotando los neumaticos con tpms, gracias
What model Foxwell is that?
I think this one is discontinued you can buy now nt1009 or gt75ts
What foxwell is that? Nt1009?
Don't think it's that model. NT1009 has a 10.1" screen, I'm going to say it's the GT65 maybe...🤷♂🤷♂
Hallo can you guide me wit cvt calibration please.
Just replace valvebody toyota avensis
Three things need done reset memory then g sensor calibration then cvt pressure calibration
Hi..My Camry 2013 gear pause itself and lagging. It can fix.?
Yes just reset
@@CarFaults thanks guys still am looking some one around uae -dubai
Good evening guys,
Can this foxwell reset Toyota Camry 2006
Yes
it works on hyundai sonata 2009?
Yes sonata also have reset transmission values
What kind of foxwell is that?
Now there is a new version of foxwell
How is he reseting the car without any wires connected to the tcm or obd2 scanner port
This device has wireless obd device
@@CarFaults I have a question. I had replaced the 1, 2, 3, and 4 shift selenoid, and the transmission control selenoid in the engine bay, but my car still shifts a bit late and the d4 light starts blinking after I try accelerating. I'm guessing maybe I need to reset my cars computer, do I need to have the transmission reprogrammed sense I replaced all the selenoids ?
@@BobiPhettOfficial looks like you are talking about honda vehicle what you mean by late shift is it slip then shift
@@justtrue8228 I have an accord 2000excoupe. Once I shift from park to reverse, you won't feel the car actually shift gears until like 2 seconds. So it'll slip then shift. When I switch from reverse to D4 D3 D2 or D1, the car doesn't really shift slow, it kinda catches it fast enough, but the thing is when I accelerate up to about 10mph or more then let go the gas pedal it feels like the car isn't upshifting for me and the transmission kind of makes a small small jerk, & the D4 light starts flashing with the check engine being brought up. This started happening after most of the transmission fluid spilled on the floor due to a bolt that I didn't tighten all the way. Of course I put more fluid in it, the red Volvo ATF one that's says its compatible for toyota and Honda vehicles. Just mind you, i havnt deleted any codes after replacing those parts. If you know anything about this it will help🙏🏼
@@BobiPhettOfficial don't waste more money on it you already need to replace this transmission or rebuild it if torque converter and oil pump in good condition
I think you forgot a step... You should first click A/T Code Registration and enter the new 60 digit number on the label attached to the transmission.
No thats a different thing if reset memory not work which actually work all the time then i go for a t code
Can it do isuzu light trucks
12v system yes
What is the name of this scanner
Foxwell
Hey bro can a innova 3100rs do this
Yes
Now there is other tool I review this is old check video
XTool D9S PRO: The Ultimate Review Updated Version of D9 Pro
czcams.com/video/Rhwy0hClhkQ/video.html
No removing battery will not do reset to transmission