My Airplane Cracked | Getting our 1967 Mooney Airworthy! Ep 3
Vložit
- čas přidán 5. 04. 2024
- Let's restore my 1967 Mooney and Get the Wife High! How do you know if there's a Pilot at a party? Don't worry, he'll tell you! This project is one of the many things we cover on this channel. If you love aviation and machines you'll love this series!
Become a Patron: / herbomatic
Affiliate Links (Wife and I get a small cut doesn't cost you any extra)
Needle Nose Pliers EXCELLENT: amzn.to/43OTim3
Tri-Flow (Best Spray Lube): amzn.to/3VOh7IH
EZ Turn Lube: www.aircraftspruce.com/catalo...
Subs at time of posting: 40,193
Some of your comments make me burst out laughing, others are crazy helpful or informative.
Disclaimer: These videos are for entertainment only, do not attempt anything you see in these videos, I do not accept any liability for loss or injuries sustained after watching this content. I am not an expert at anything and these are just things I'm doing personally. Do not take advice from me! - Zábava
After a long day I was ecstatic to see your -wife- video in my feed.
I know what a "cowl" is but every time you said "cowl" i heard "cow" and i thought to myself "why would they name that piece a Cow Plate" 😂😂😂
Anyway, fine job on the "found" motor, random parts, half-assed maintained, fall out of the sky, plane rebuild. You seem to be a quite competent aviation mechanic.
The list...
Bomb shelter refurbisher
vending machine extraordinaire,
general badass rebuilder of most things...
and now "plane engineer"
who knew?!?
Keep up the great work. You're doing a fine job
I've always predrilled holes with pilot holes. In fact I drill pilot holes for my pilot holes. But I'm also a pilot so it's a relief to know I can ditch this unnecessary step. Thank you!
As long as you're current with a your biannual flight review you can skip the pilot drill.
Cleco no klinko...lol. I found this to be a riveting episode, still holding my bucking bar.
Don't play with your bucking bar while watching me!
"I don't know if one gets hot and one gets cold, that works on me" ...Your serious tone of voice makes that even more hilarious 😂
My brain is always saying that bs inside so now I just say it on the outside and throw it on YT. Thanks Greg!
Our brains can be funny but few dare to say it out loud 😄
Hey Herb, I loved this, really hypnotic actually to watch you do airplane mechanic things. I found this quite riveting. 🥰
First with the riveting joke! Thanks Cake!
@HerbOMatic wondering: were you a vending machine tech first and got into plane mechanics, or the other way round? And did you ever accidentally mix these topics up?
I would like to Thank the Patrons, that music is FIRE! Like always another informative video, with humor, thanks.
Lol, it felt right for that scene. Really the mic malfunctioned and I lost audio, so I made that montage.
I’m fairly new to your channel, I just gotta say this was for me one of the most interesting things I’ve watched for a long time. Keep up the great work!
Thanks Billy!
Same
Hey Herb, my first time commenting. Love the Channel, great videos. Love your sense of humor, keep up the great content
One of his strong points that make his channel successful. The ridiculous chatter doesn’t wear on you, and it never gets old!
I'll keep doing it! I appreciate the love, even if it's just this one time.
Always enjoyable to watch you work on a project (despite this episode not having the usual surplus of gratuitous butt shots). I kind of get the idea that whatever you spend on an airplane, you have to spend an equal or even greater amount on tools to maintain it. And we all know specialized tools don't come cheap.
I haven't even scratched the surface on crazy specialized tools! For now I try to make things work. I was disappointed when I went to edit this episode, there were NO butt shots in the raw footage. It's going to affect my ad revenue for sure.
A good trick is to let your beard and mustache grow real long and bushy so that it catches all the particles from grinding, it's like a natural respirator...Hope that helps...thanks for sharing!
9/128", #4 rivets, #10 drill... you guys will really do anything to avoid using metric, won't you? :)
I would change but it would take me a 129/21 of a fortnight to get the hang of it.
Here in Europe we are blessed with metric. No head scratching. I feel sorry for the Americans forced to use both 😄
Love your style, very entertaining, thanks Herb-O-Matic
You got it Corbin Dallas.
Those are some neat tools you showed off here, I appreciate the demonstration.
It looked very satisfying and rewarding to see you put your bit into the dimple. Almost educational.
Hey! Satisfying is good, but we don't do educational around here.
You have enlightened me in some tools that I have never seen before as well as the body clenching details to check the amount of tension applied
"Boy is it hard to find pants" 😂😂😂🤣🤣🤣
You're a cool dude! Big fan of your humor! 😂
Mad props for the comment bro.
Looking good bud, nice to see someone saving and maintaining an old airplane.
I paid 45K for this bird and turns out she had a bum engine. New ones are twice what a house costs so if I want to fly I'm working on it! Also it's fun.
18:30 - Sounds a bit like like Raymond Scott. Please post the music sources in the header please. Keep up doing what you do. You make me smile. The joke from the last video, three dudes and the genie, was a great smash hit where I work with everyone except H.R. Thanks!
fun to do stuff when you have the proper tools.. specially that switchable metric to standard wrench 😂😂
Saves alot of trips to the hardware store.
for measuring centers of holes you measure on either both left sides or both right hand sides of the hole distance between gives you the exact center
"Woops, it's not my birthday." 😂
🤣🤣🤣🤣
Wasn't sure anyone would catch that!
darn it, came for the laughs, stayed for the learn. ❤
Don't go tryin to lern stuff aroun her.
clinko... I thought they're called cleco fasteners. At least that's what the box they come in says. Idk, maybe it's a typo. :)
I just looked it up, you may be right! Potatoes Tomatoes.
I was glued to the screen for all 39:24 of riveting content. Herb does not disappoint.
Thanks Cory!
Really interesting all that aviation stuff, can't wait for the next episode! 👍👍👍👍👍👍
I'm working on it!
@@HerbOMatic That's awesome 😎
Ix-Nay on the Arbor-Hay Freight-Ay (that's a coded message for Herb). I don't want people to discover that they now have pretty good tools at a great price. If more people discover this, they will raise their prices, and you will have to sell even more candy bars to pay for them while keeping your candy stash hidden from the wife. A tough task indeed.
They have gotten better! Man they were junk. With their new lines I can afford decent tools for a reasonable price.
Is the reason you didn't weld it back together because it would anneal the aluminum? I'm just curious.
do that to end nippers and it will have more leverage to cut the rivet.
That's a really good idea, in the RV forums those dudes are disassembling whole wings with side cutters.
Im glad you got your cow fixed 🐄
Dang cow flaps.
You play the cocky-glib-guy perfectly, but I’d let you work on my plane, if I was a pilot, and I had a plane, any day! I have a hearing impairment and it took me a while to figure out what the autogenerated closed caption was displaying as a “cow flap” was. Sounded like a name you would make up so I just figured….you know. Thanks, it’s always interesting to be shown stuff (special tools and gauges) that is specific to strictly regulated procedures and standards. I’m a wood worker and love me jigs, sleds and gauges.
Lol, Cow Flap is something I would say! When the Wife is having a cow you open these flaps and the wind noise will drown out her droning. Those little jigs and gauges are cheap insurance.
Funny you mention drilling into your finger while using rivets and clinkos. My dad built 2 gyrocopters and 2 airplanes in his life. All were “experimental” kits. Lots of clinkos and riveting for the airplanes at least. When I was maybe 12 he was building a Capella and came running inside from the garage with a fully bloodied rag on his hand and ran to the bathroom and my mom and I followed him and he had drilled a hole into the side of his finger while preparing holes for rivets. He refused to goto the doctor for stitches and just cleaned it up and wrapped it up himself. He was done working on the airplane for the night after that mishap but was back at it the next day after work. Be careful dude!
Your dad sounds rad! That's brave to fly something you built from scratch, I hope to do that one day! I try to be careful but have been cut pretty bad, one time I cut an artery in my leg and before I passed out wrapped several layers of duct tape over it. I passed out and woke back up starving. I would have died if not for duct tape.
@@HerbOMatic Duct tape, Super Glue. Whatever it takes. That’s sounds like a harrowing experience. He wanted me to be a pilot but I didn’t want to do that. I loved flying and he let me fly the cappella a lot. I learned to take off and land it but wasn’t really interested in getting my pilots license. I was way more into cars and he was excited about that too and always worked on my muscle cars with me. Going to see him tomorrow actually. Our current gig is RC truck racing. We might build a track in his field this spring. Maybe I’ll film it and start my own channel. 😂
Whoa, we're half way there Whoa oh, livin' on a prayer, Seems timely...
I hope Bernoulli doesn't let me down, let's pray to him.
@@HerbOMatic Shall we lift our leading edge in prayer?
Congrats on doin your own A&P work,,last aviation work I did was on an SH60B earley 90's on a flight deck,,,good times
That Sikorsky is a bit more complicated than this Mooney!
My wife's dad had a Mooney. When she was 11 he flew it into some moderate turbulence and the tail separated from the aircraft. There wad an A/D out on it that required a check for cracks in the frame during annual inspections. The plane was a few weeks out of annual so he was deemed responsible. He didn't survive.
I've never heard of a Mooney tail separating, are you sure it wasn't a Bonanza?
Gotta get the HF caliber’s. My expensive ones don’t convert to fractions.
Yeah, the HF calipers are cheap and work fine.
Funny stuff. But informative.
It's really a shame that you live so far away from me. I would weld the aluminum back together for you in my workshop. Thanks for the many great videos you two made.
I never learned to weld Aluminum. I need to get a good tig one day. Man, the more I learn, the more I know I don't know and the more tools I need!
Your offer, while very generous and well meaning, would have robbed us of another humorous, prolonged version that makes a boring airplane repair video great content. Thanks anyway, lol.
He lives in Avondale, he doesn't live close to anybody. Lol.
Heat to soften the aluminum 1st. Work it. When all shaped heat and rapidly cool to harden.
In airplanes, they get weird about heating or welding aluminum. They outline what you can do in AC 43.13 it's available for free online.
👍✅ Tks Herb, funny and informative as always😂
Thanks ParatyShow, I'm trying to crank them out while getting my projects done.
dude is funny!! would be hilarious if he could get his own little segment from time to time, like put him in a funny suit and have him read the dude news XD
Dude is awesome! He can't read though.
@@HerbOMatic damn... that witch set a hex on him :'( poor dude
Your wife would probably like the engines I used to work on (Trent 900, 1000, and XBW), because they're way bigger than yours.
if you're wearing headphones and have your volume up, jump straight in here: 23:35 you're welcome
It's aweful, why did he do that. Nail on chalk board.
Nice work. Surprised you didn't just take the cowl home to the workshop though.
I get weird blind spots in my mind and I don't think of the simplest solutions!
Great job. I wish I had that rivet tool in the Navy, it would have saved me hours of work with a hammer and buck. When do you have to have a A&P check your work or do you?
Those squeezers are my hangar neighbor's he's generous, I will grab a pair one day. I have gotten pretty good with the gun to the point where it's not too much hassle but If I had alot to do the squeezer sure is low drama.
Something tells me that you have *_DONE_* this before!!!
Were you in the USAF or an aircraft mechanic at some point? You make this stuff look interesting. Maybe it's the commentary...
I did not serve, just tinkerer. Thanks Joe I'm working on more!
The smell from the drill is the soy insulation on the wires inside. I hear they are tasty aswell.
Another awesome episode, Thank yoiu Herb and wifey! ❤ I don't understand how you can understand the imperial system, metric with millimeters are so much easier just straight up a clean number, not fractions like you have. I've tried all my adult life to understand the imperial, it just.. I don't know.. it's crazy! 😋
Can't wait for next episode, whatever you do, always interesting and fun to watch! Always, always love your comments throughout the videos❤
The metric system makes sense. Problem is I was raised on this stuff also there is a ton of metric stuff here too you gotta get a sense of both over time. Aviation is very SAE and probably going to be there for awhile!
So after repair do you need a licensed A&P to inspect?
Yes, you have to have an A&P that you are working with. There are provisions in the regs for that and it's a way to build experience to get your own A&P license.
Brought to you by Craftsmen.....
Few hundred for tools to install $1 worth of rivets. I know. I know.
I may have accidentally learned something…. Maybe
Sir, I make these for entertainment purposes only!
@@HerbOMatic i assure you, it was an accident. Going by my wife, I am normally in capable of learning
I really like watching and learning high standard machine work. You're a pretty fart smeller
Klinko
What is it with this channel and cracks? 🤣🤣🤣
I wanted to put "crack kills" on thumbnail, still might!
@@HerbOMatic Crack is whack.
Why not aluminium welding the cracks?
Heat weakens aluminum. This aluminum is tempered for strength so heat will goof it up.
@@HerbOMatic Ahhhhh
Cleeeeco
I have to buy off-brand klinkos. I'm not made of money!
RIvet squeeze... gross but LOL
You saw it?!
Herb-O-Matic come on down to play CLINKO.
I may have got that name slightly wrong! Maybe they made the game and the rivets and forgot to change the name.