ESU Switchpilot & KATO Unitrack Turnouts
Vložit
- čas přidán 4. 05. 2012
- ESUのSwitchpilotでKATO(ユニトラック)のポイントを動かしてみました。つなぎ方が分からず、半分あきらめていましたが、今回、やっと動かすことができました。KATOのポイントを動かすためには、Switchpilot Extensionが必要でした。
Switchpilotは、鉄道模型のポイントや信号などのアクセサリーをデジタルでコントロールするためのデコーダーです。1個で6個までアクセサリーをコントロールできます。つぎは、踏切のコントロールにチャレンジしてみたいと思っています。
I tried to control the unitrack points of KATO using a Switchpilot of ESU.
Ich habe versucht, den Punkt der KATO mit einem SwitchPilot von ESU zu kontrollieren. - Auta a dopravní prostředky
Hi Jim! Thanks for the comment!
I know that some people want to control the KATO points by the switchpilot. So I, somehow, considered how to do it. The solution is an answer to control them, but we cannot find it on the manual of switchpilot and the ESU forum. I found again that the ecos is a very interesting useful item. I will learn more about it.
All the best Tak
Hi tak intresting vid, intresting cross over section of track too, good to see you solved the problem & to post your solutions for others to see as there is not a lot of info in this area for the ecos & switch pilot etc. there are many settings for the ecos which i am learning about, i am now converting all my points to this system inplace of the standard push button fleischmann switch. Thanks tak....
Thank you for the valued information!
I know another special decoder for the KATO turnouts produced by Digitrax. It can control up to four turnouts like the ESU switchpilot.
But, recently, the decoder always sold out in Japan.
Greetings Tak
This is the point of we should call someone! :)
Very interesting video, thank you for the elucidations.
コメントありがとうございます。このswitchpilotでは3線の真ん中がコモンとなっているので、おそらくプラスが1極でマイナスが2極ということだと思います。
DCCでは、各車両に搭載したデコーダーに番号を記録させ、その番号に応じて各車両を個別に制御します。簡単に言うと、線路には13V前後の電流(交流)が常に流れていますが、1番の車両に「走れ」という指令を出すと1番が動き出します。一方、2番の車両は止まったままか、逆に走らせることができます。また、1番に「ライト点灯」という指令を出すと1番のライトが点灯しますが、2番の車両のライトは消えたままにできます。ポイントにも番号を付ける必要があって、指示を出したいポイントの番号を選択して指令を出せば、そのポイントが作動します。ただ、ポイントの数が少なければ、ポイントだけDCで制御した方が素早くコントロールできるかと思います。さらに、Detectorという機器を導入すると、各車両が今どこにいて、何をしているかをPCの画面に表示できるようになり、PCで各車両やポイント、信号などの自動制御もできますが、この辺はこれから学習しようと思っています。
ご覧いただき、ありがとうございます。「参考なった」というコメントが一番嬉しいコメントです!
ヨーロッパではコイルが2つ付いたポイントやサーボを利用するものが主流のようで、ESUはKATOのポイントのことは考慮していないですね。自分がやってみたのはマニュアルにはない変則的なつなぎ方です。私はレイアウトにポイントを埋め込んでしまってからDCCを導入したので、switchpilotのような外付けのデコーダーがどうしても必要でした。switchpilotはつなぎ替えが簡単にできるので、いろいろと使えそうです。購入前は、4個か6個のデコーダーに相当する製品かと思っていましたが、使ってみるとデコーダーとしては1個で、ファンクションに相当するものが6個ある仕組みなのですね。
コメントありがとうございます。デジタルだといろいろできるのですが、コントローラーの画面展開がまるでintelのceleronでwindows Xpやってるみたいで、素早くないです。せっかちな自分としては、KATOのアナログポイント切替機で操作した方が格段に速くて良いと思います。デジタル制御はハンブルグのミニチュア・ワンダーランドみたいに人にたくさんの列車やギミックを見せるときには威力を発揮しますが、普通の家庭のレイアウトだと「面白半分でやってみた」ぐらいの感覚かもしれません。一方、屋根裏全部使って複雑なレイアウトやっている人には、デジタルは本当に面白いと思います。
Thank you for the nice comment!
こんにちわ。
凄く参考になりました。わたしもSwitchpilot Extensionを
入手して試してみようと思います。
Very well done video instructions,followed to the letter and the Kato points work perfectly
Are you doing any more videos i have a long wish list.like setting up routes and
lights and stops the list goes on and on
For its people like you that can work out the problems
People like me who rely on people like you
many thanks
roger Newton
そう言えばPECOの電動も3線式だったかな?マイクシールドのようにマイナスが2極なんでしょうか。それにしてもDCCでポイント制御はコントローラースイッチを配列しなくて便利そうですね。しかしヤードが複数存在する場合即該当ヤードを呼び出し出来るのでしょうか?DCCは今年にはチャレンジしたいと思っていますので色々と参考になります。
My layout has 10 switches and 6 uncouplers. How many switchpilots and extensions am I looking at?
A switchpilot has switches up to 4 solenoid accessories (e.g. points) or 8 loads such uncoupling ramps. in detail, i recommend you to see the ESU website. Thank you for the message.
I also use Kato-Turnouts, but I use special DCC-Decoder for the two-wirde-Kato. So, you have only two wire from the turnout to the decoder. The decoder is like this: (look for jokashop dot de in google)