Installing Solid Tyres on the ZERO 10X
Vložit
- čas přidán 10. 09. 2024
- Here is a quick installation guide for the Solid Tyres on the ZERO 10X. It is made simple enough so you are able to do it alone at the comfort of your home!
THIS TECHNIQUES can be used for all the installation of solid tyres on ANY MODEL.
DISCLAIMER: PLEASE MAINTAIN EXTRA CARE WHEN FOLLOWING THE SUGGESTED ACTIONS.
For more information, visit our website www.FalconPEV.com.sg or enquiry with us on Whatsapp @ +65 8748 4565
For those that are on the fence about solid tires.. If you are having flats often, then use slime. That is an absolute must. If you slime it, it will rarely get flats.. I havge a zero 10x
Why did you skip the most important part of the video? How did you fit the motor hub into the rubber wheels? I order the honeycomb solid rubbers from the link on the description. I have Boiled the wheels for an hour, I have microwave it and I for the love of god cant fit the motor hub into it, just doesnt work.
One of my m5-20 hub bolts was crossthreaded at the factory. going to be lots of fun drilling it out and fixing it. But back to your video, great trick with longer bolts! You come up with some super ideas.
You can purchase the airless honeycomb tires here www.falconpev.com.sg/collections/zero-accessories/products/airless-solid-tire
I used 2 bar clamps instead if the longer bolts it worked perfectly...very happy no more hours of labor.
I was told this scoot would create too much torque for solid tires? Care to comment, are there specific tires for higher torque etc?
Also I put a little WD40 in the hub threads to prevent them from stripping as you put a steel bolt in an aluminum thread.
Where can I buy a solid tire for my dualtron 3? (10x2.7)
All this microwave this and boil that.. just use washing up liquid on both sides of the tyre and on the rims, coat it with your finger or if you dont like clean hands, use a small brush. This acts as a lubricant and just enough time to get the tyres on. You need 3x M5 bolts 50mm (full thread) using in a triangle pattern and secure them one at a time, not to fully tighten 1 up fully, small amounts on each, this will pull the rings together, Slow and steady is the key. Once the 3 bolts are secure and dont go any further put the other 3 normal bolts in, Once thats dont take out the long 50mm bolts out and replace with the normal length bolts. When you 1st start it looks like the tyres do not fit, this is normal as they are not soft tyres so its like trying to fit an inflated tyre on a hub thats why there are 2 parts! and another reason if you damage the motor ring ( this side has thread) you need a new motor, if the other ring is damaged ( no thread ) you can just buy a new ring. As the solid tyres have no Give in them you will have to unplug the motor and hall sensor wires back through the scooter so the wires can go though the tyre. The hall sensor wires are in a quick release plug, just unpick the 5 wires from the plug and they all go though to give you more room or try with the plug on but is better to have more room.
I'd much rather boil my tire for 2 minutes, rather than having to get all the way into the controllers for something pretty simple.
Don't fix what ain't broke.
Do you guys self service the scooter? Like installing solid tires and then shipping out?
Solid tires in fast Electric scooters are scary and dangerous in high speed its better with pneumatic tires since zero 10x is easy to change tires because its a split type :)
MrZones21 yes and no.
Have you ridden the 8x
Enjoy your flats
mine puncture every few weeks, constantly taking wheels off and changing tubes. I think it's the split rim that causes the issue, my tubes are alway split in the same places and never punctured from external. I just sanded the sharp edges off the split rim on mine to see if that helps.
FYI you won't have that much slack on the motor wire lead. Make sure you have something to prop the motor on so you can work on it without stressing the wire lead.
I own a evercross scooter that use 10 × 2.70 tyres
I wonder if this solid tyres might work on my scooter.
Would you please tell me or give me an advise of a company that should get me the right tyres?
I would appreciate it.
How about a riding video on the solid tires ???
Will these work on the varla eagle one? Please let me know
Yes but only up to 45 kmh
OK thanks. Where can I get them?
The text was a little hard to read with the choice of font and no background behind text.
can anyone please tell me which solid tyres should i use for kugoo m4 (size) ? thanks
Hello Falcon pev. I need your advice what to do bout my zero10x when im accelerating the body of my sccoter is vibrating i do not where it coming from .
Raffy Bato hi check your motor wire it could be broken or loose
Have the same issue with my 10x at half throttle...
where can one find those three longer allen hex bolt?
hardware store. or online from McMaster, they have every screw and bolt imaginable
Is it possible to install an air tube/tubeless tire on the ZERO 8X?
Is this similar for the kugoo kirin m4 pro ?
Yes should be, 10 inch motors
Hi I have a zero 10x and my solid tire keeps popping off the rim when I’m riding. What can be the problem? It is a 10x2.5 tire
Hi Faisal, when you fit the tire, was it fully tightly in?
@@FalconpevSg yes, it was fully tight. It has happened twice. What size is the tire that you put on in this video? And where can I buy it? Link?
@@faisalwaheed677 where did you buy your tire? Can you take a pic and show us?
The real question is where the hell is the link to get these tires??!! I need these tires for my Mantis 10
C'est bien de mettre des vidéos mais est-ce que tu peux me mettre le site où tu as acheté le pneu plein pour la zéro 10 x
Bought a Zero8x from rev rides ride it about 100 miles tire came off the rim , I reseated the tire, yet tire continues to fall off if scooter goes over 20 mph . Is there a solution to this dangerous problem
Same, i bought zero 8x and the tyre came off the rim and damaged the motor cable. How did you get the tyre over the rim :o looks impossible to me.
To reinstall tire u need to use plenty wd-40 on the edge off the rubber tire, then wedge a small flat screwdriver between the rim and tire, when you have a large enough gap place a large screwdriver or small angle cro-bar or a (tire pry) start spinning the tire making sure the lip seats onto the rim as you spin the tire back on the rim, just like a car tire machine works at an auto shopThis will work easier if the tire is hot so you may want to leave it out in direct sunlight for several hrs before doin so .... it’s easier with 2 people as well one to spin one to use tire pry ....the reason it fell off ... the heat of the Motor causes the tire to loosen off the rim . It’s a design flaw
The wires can be reconnected using butt connectors or electric tape good luck ....it’s not all that hard once you get the hang of it
Don’t forget to remove brake before starting
@@Nicholascovicci Thanks helps alot, Kinda scared that it will happen again on a brigde riding max speed.
Do you have a link to this tire?
Here you go You can purchase the airless honeycomb tires here www.falconpev.com.sg/collections/zero-accessories/products/airless-solid-tire
@@FalconpevSg that link is dead.
@@abundantharmony thanks for informing www.falconpev.com.sg/products/honeycomb-airless-solid-tire?_pos=1&_sid=73fd65e1e&_ss=r&variant=29061281054787
How does the scooter handling change with solid tyres?
It will run slower and it’s more slippery
it will run slower because the solid tire is heavy, I stay with the regular air-filled tires but use the (SLIME TUBE/TIRE) brand, not the regular Slime!! in all 6 of my scooters and it works flawlessly. no flats on any of my scooters they all have road tires though. the product comes with a 2-year guarantee
@@lionelhowell4972 unfortunately slime doesnt work even 50% of the time, only works for extremely small punctures less than 2mm in diameter. and even then, its not 100% of the time.
@@FalconpevSg notice what I said, the new formula is called TUBE and TIRE not the regular!!! I went all summer using it and it does work!! I have removed glass, a roofing nail, staples, out of my tires at times, and not a seep. they guarantee some products for a reason. and this has been WORKING for me..
@@lionelhowell4972 we are pretty sure it doesn’t work, we have fixed tubes for 8 years.
Can you show how to waterproof inokim OXO, since it's near to be rainy season?
scarlet ruby when you have time we will
hi excuse me a question where can I buy those tires for the zero 9 in New York
Aliexpress.com
would these fit on a Zero 10?
hello guys , just got my zero 10x, and i want to change the tires to solid tires,,, where can i get them from? thanks
get them on Alibaba very cheap $4.50 us
Where can I purchase those tires??????
Hector Aguilar here you go www.falconpev.com.sg/collections/zero-accessories/products/airless-solid-tire?_pos=1&_sid=062c99351&_ss=r&variant=29061281054787
Received my solid tyres from you guys this week. Did you remove the rear motor connector to install the solid tyre ? I've removed the standard tyre using soapy water but have got no idea how to get the solid tyre on. Your video doesn't show that part, you go straight into tightening the rim. Any help would be appreciated. Thanks
Neil Winch hi! Can you email us for technical help? Sales@falconpev.com.sg
Did they ever tell you how to install it to the scooter?
@@PirateOneShot forreal just got these tyres and it its not fitting, how they got them on?
Whats the size of this solid tire
How did you fit them on the rim. Heating the tires doesnt seem to be working and how long screws do i need for the solid tires
put the tires in a microwave for 1 min or in boiling hot water for 2 mins, it will work.
@@FalconpevSg i used water and m5 50mm screws it wasnt that hard to get them on
@@perunao4823 glad to hear that!
Dude what kinda of water did you used. I have boiled mines fir an hour and they barely get soft. Motor hub doesnt go in at all
@@gameburrito2502 as hot as water as i was able to get from the tap. I let soam soak for good while. Ofcourse you could use microwave but the smell will hit u in the face
How do those solid tires ride.
Is it super bumpy
I got some on a mantis. The suspension make comfortable... of course not as comfortable as pneumatic. But the largest flaw is they're not as safe. The slip when braking and definitely DO NOT turn a corner at 0ver 18 mph. But you can go in straight line as fast as you want. Also the motor gets hotter with solids on there. So be sure not to push them too hard. I use them for a slow daily commute
What kind of drill would you suggest buying?
Dewalt
Dewalt
на ali express есть такой товар?
Now solid tyres for the 11x!
Why would you put solid tyres on such a beautiful scooter?
I was riding my scooter at 20mph and it just went flat. I fell over really badly but by jacket saved me from damage
@@kojinmaster Stay safe 👍
@@kojinmaster hello! How often does it get flat for you? I was thinking of buying this scooter. Thanks!
@@claudiuiordache410 I get flats in the rear wheel 3 times in a year.
@@instars2027 That sounds like the tires are very good quality. On my Xiaomi m365 I would get one after a few weeks.
Would of loved to seen a ride with these tires im considering buying them to place them on my nanrobot d6+ wich uses same tires as zero 10x
Did you buy them? If you did how much does it effect the range and speed
link to the tires please?
Better to instal honeycomb tires
cause regular tube tires standard on Zero scooters are the worst shitty tires you can get... flat tires on and on... Actually zero gives you the regular tube tires because they cost pennies... the honeycomb cost a few dollars... but still if you buy them they will cost you over $30.00 a piece... unless you get them on alibaba at $4.50 And more the power trigger is the cheapest on the market ... Zero scooter are way over priced.
I have zero 10x
как заказать в россию такую покрышку?
Никак только на вли
Not one word about how to remove the wires from the power box.Absolute worst tutorial ever.
We thought to include it but thought it’ll be easier to cut an apple instead.
cheers for the information I'm changing to a solid tyre on dt mini so this was fantastic never put solid on