I followed this guy's instruction step by step and honestly he made it far easier than anticipated. I'd heard a lot about challenges with getting the spring wire around bellow, so when I got to that part I got a friend to help and still it was a struggle. So I went back to Steve and did it exactly as he showed and it took two tries. My sincere gratitude to you, Steve!
This is a FANTASTIC video and Steve walked me through the install. Just a major caution: The hardest part is getting that spring loaded band onto the baffle on the outside right at the end of the job. No way it's a one-man job to do this spring band. You need someone to hold the band in place while you use TWO needle nose plies to spread the spring out at the 6 oclock position. Last thing you want to do is puncture the baffle you just replaced with the needle nose pliers as you finish up with this spring band trying to do it yourself. Otherwise, I commend Steve for you great video.
Took me like 4 hours of messing with that seal-- and my hands are sore, BUT I DID IT! Could not have without this video. Thank you thank you thank you! You saved me $225.00!!
Thanks for this video, it helped me a lot. Of course the part does not come with any instruction. One important tip given is the one to use a little soapy water to lube the bellows going in. I needed a second set of hands to get the outer spring clamp on and used two sets of needle nose pliers to spread the spring to get it over it's ridge while my wife held the rest in place. No leaks, we're happy! Thanks again.
I just changed the bellow on my washing machine following the steps shown in this video. I was surprized how easy it was. Steps are easy and well explained. Thanks you sir for sharing your knowledge with us.
Thanks Steve! Followed it step by step - going from your video to my washer - and got the job done in one evening. Not stressful, and super helpful! You made my task an easy one with such great instructions. THANK YOU!
Thank you so much! My son and I were able to do this, it took us a long time, but we are total novices. Just did our first load of laundry in a week, we were successful no leaks!!
Thank you for video. I thought I wouldn't be able to use the washer any more. But I'm glad I don't have to junk it. You saved my washer! How wonderful!
thank you very much for this video, getting that baffle started was a pain in the butt, I , at first, was trying to install the baffle backwards. that was a fun 15 minutes. once I flipped it and could feel how it went it it was just a matter of perseverance, man vs machine... I kept getting half of it on then it would somehow pop out and I'd have to start over. then we brought in another set of hands to keep is stable. this was when I could see light at end of tunnel. overall took me a little over an hour, doing it again, i'm sure i could trim off 20 minutes. Good Luck to the next guy or gal.
Great video!! However this is harder than than it looks! This man is a professional and it shows… My first problem was trying to get the new baffle between the drum and the outside cylinder. After 2 hours I gave up and went at it again the next day, took me an hour the second day to get it in place... Use plenty of windex or cleaning solution to lubricate it, it definitely helps. The second problem was the ring with the spring. It easily took my son and I 10 try’s to get it. Every time the baffle would pull loose. I have run a load of clothes and no leaks!! Yay! Next time I will not think twice, and pay a professional!
You are my hero! I was able to do everything on the repair except install the second wire/spring on the front part of the bellow. Using the needle nose pliers that you showed, along with a couple plastic bicycle spanners (normally used for mounting bicycle tires onto rims), I was able to mount that wire/spring and complete the repair. And nothing leaks! Thank you so much for posting this!
Perfect! Everything went perfect! THANK YOU! Also it’s helpful to have someone hold the top of the baffle when tucking in between the drum. Another hint get it wet so it slides in!
Great instructions! My Whirlpool Duet is slightly different but I took pictures as I was taking things apart and was able to get it back together again along with this video. As other have stated, the 2nd spring clamp is a serious pain but with another pair of hands holding and many attempts, I was finally able to get it on. It took me about 2 1/2 hours plus a sanity break while putting the clamp on. Thank you so much, I never would have been able to complete this repair without you.
Thank you for sharing this video! It was very helpful with some great tips. I changed the bellowe in my WFW9050XW00 today and the only difference from the model you did was there was no screw at the bottom (in the centre) of the control panel. The left side screw for the panel it’s a Torx head bit as well for some reason. Great job on the video! Thanks again!
This was very helpful. We replaced our moldy seal with a new one. The one issue we had was the wire assembly for the door lock became unplugged and we didn't realize it before putting all the panels back on. On trying to run a cycle, the light for "door lock" was red but the door would not lock and the cycle did not start. We had to take everything back off to realize our mistake. So I suggest double checking all wire connections before putting everything back together. Took about 2 hrs start to finish, but we basically had to do everything twice.
Thanks for this video, it helped me a lot. Of course the part does not come with any instruction. One important tip given is the one to use a little soapy water to lube the bellows going in. I needed a second set of hands to get the outer spring clamp on and used two sets of needle nose pliers to spread the spring to get it over it's ridge while my wife held the rest in place. Note: I also did NOT have to remove my dryer from on top of my washer as I got the upper face plate off without doing that. No leaks, we're happy! Thanks again.
This video helped immensely. It took me a little longer because I had to move my washer out of the room. For the spring loaded front band, I used needle nosed pliers and needle nosed vise grips. The needle nosed vice grips held one side of the spring, while I pulled the other side with the needle nose pliers.
I am doing this job right now and for my Whirlpool WFW9050XW03 It wasnt simple philips screws. 7/64th Allen Key needed for single screw where detergent tray is. T20 Tork Keys needed for 2 screws at door lock aswell
Great how to video. Was dreading doing this but I was done in under an hour. Good tip on lubricating the seal before putting it in. It allows for a small realignment if its not quite right. Thank you.
I've replaced my Whirlpool Duet bellow tub seal 3 times now, every time I need a refresher to build my confidence on the proper process and this video is perfect. Knocked it out in about an hour today. No leaks and I feel good about the replacement. Thank you...saved me money, time, and stress (only had to halt the laundry cycles for 4 days), and completing it on my own. Yes!!
thanks for the instructions. i didn't have to take off the top panel. this was signifixant as I have mine stacked with dryer. also I use a drill for the screws much speedier.
At the 1:53…I have a Whirlpool Duet WFW9750WW01… I don’t see a tab. It appears that screws are holding it in place. Is that the case on this model? Looks difficult to reach those screws.
How imperative is it to remove the top of the washing machine? I have a stacked washer and dryer so removing the top of the washing machine would mean removing the door to the bathroom and getting 2 guys to come help me lift the dryer out of the bathroom...
I didn't remove the top. Just the screw in the middle top where the door is holding in the panel and the one screw by the dispenser and it popped off the control panel
With the repair completed, I'm getting a LF code. Is there a sensor or a level I should check or replace? When I turn on a wash cycle, it turns on, the water begins to enter as usual, then after a couple of seconds it trips the electric outlet.
It took like 15 minutes to install the rubber seal. Spring loaded band was the more tricky one . Idk what's so hard everyone is saying. Spray some Windex and tuck the seal in all around
I am having so much trouble installing the bellow to the lip. Every time I try to slide it on the lip it’s completely come off! Beyond frustrating. Gave up, trying again tomorrow.
It should mostly drain through the holes at the 6 o'clock position. I usually have about a tablespoonful of water there which I will wipe out with a rag. If you leave the door open between loads of wash it may evaporate, if you close door with that little bit of water in it, it will get pretty nasty in a day or two.
It is definitely NOT a "really easy job" as you say. In fact, it has been the most frustrating DIY job I've ever undertaken. Getting the bellows to fit and stay put in the slots was a nightmare. To be honest, after three days I'm still trying to get the spring-loaded ring to fit without pulling the bellows off its groove.
So followed the instructions now you can’t turn the inner drum, there is a horrific squeal sound when it try’s to spin and there are rubber shavings from the boot. What in the heck?
I bought the replacement part for model wfw9250ww00. I called whirlpool for the item number. I was told it's w10290499. I went on eBay to buy the replacement. we tried every way to put it in and just wont go in. I have a feeling that we were sent the wrong below. Is there a way you can show us how the right below looks like? I already broke nails by trying to put the replacement in. Even my husband has given up and went to sleep.
Hello, when researching your Whirlpool model number the part # W10290499 was the original part for your model. Unfortunately, Whirlpool has discontinued the part and has made a substitution part #WPW10381562. If the part is not fitting correctly I would suggest to contacting the manufacture directly to see if they have one closest to the original that will fit and work properly for your model.
I have a Maytag and it's design exactly the same. I can't seem to get the inner band in the v-groove. It seems to be too small but I know it's not because I took it off myself. I unloosen the screw to it's Limit still want fit. Can anyone help me.
If you're reading this and can't get the bellows to tuck in because it's too small. Flip it around. The way he puts it in is extremely confusing and misleading. The wider part should be going into the machine. I just wasted 2 hours pulling my hair out.
It's easier to endure a root canal than it is to put the metal ring back around the door boot! Please redo this video without the monotonous guitar in the background!!
I followed this guy's instruction step by step and honestly he made it far easier than anticipated. I'd heard a lot about challenges with getting the spring wire around bellow, so when I got to that part I got a friend to help and still it was a struggle. So I went back to Steve and did it exactly as he showed and it took two tries. My sincere gratitude to you, Steve!
You're very welcome, Jeff!
This dude makes tucking the baffle in between the drum look easy. It’s a major pain! But still better than paying someone else to do the repair.
This is a FANTASTIC video and Steve walked me through the install. Just a major caution: The hardest part is getting that spring loaded band onto the baffle on the outside right at the end of the job. No way it's a one-man job to do this spring band. You need someone to hold the band in place while you use TWO needle nose plies to spread the spring out at the 6 oclock position. Last thing you want to do is puncture the baffle you just replaced with the needle nose pliers as you finish up with this spring band trying to do it yourself. Otherwise, I commend Steve for you great video.
Thanks for watching!
Straight forward and 'easy' video. Thanks, the second time in 13 years I've had to replace my bellows.
Took me like 4 hours of messing with that seal-- and my hands are sore, BUT I DID IT! Could not have without this video. Thank you thank you thank you! You saved me $225.00!!
Thanks for this video, it helped me a lot. Of course the part does not come with any instruction. One important tip given is the one to use a little soapy water to lube the bellows going in. I needed a second set of hands to get the outer spring clamp on and used two sets of needle nose pliers to spread the spring to get it over it's ridge while my wife held the rest in place. No leaks, we're happy! Thanks again.
I just changed the bellow on my washing machine following the steps shown in this video. I was surprized how easy it was. Steps are easy and well explained. Thanks you sir for sharing your knowledge with us.
Thanks Steve! Followed it step by step - going from your video to my washer - and got the job done in one evening. Not stressful, and super helpful! You made my task an easy one with such great instructions. THANK YOU!
Good job. Not sure why people give a thumbs down. Doesnt get better than these instructions.
Thank you. Took me about 40 min from start to finish. Worked like a charm. Putting the small spring loaded clamp was the most difficult.
YES! That damned small spring loaded clamp! I hated that part very much.
Thank you so much! My son and I were able to do this, it took us a long time, but we are total novices. Just did our first load of laundry in a week, we were successful no leaks!!
Thank you for video. I thought I wouldn't be able to use the washer any more. But I'm glad I don't have to junk it. You saved my washer! How wonderful!
thank you very much for this video,
getting that baffle started was a pain in the butt,
I , at first, was trying to install the baffle backwards. that was a fun 15 minutes.
once I flipped it and could feel how it went it it was just a matter of perseverance, man vs machine...
I kept getting half of it on then it would somehow pop out and I'd have to start over.
then we brought in another set of hands to keep is stable.
this was when I could see light at end of tunnel.
overall took me a little over an hour,
doing it again, i'm sure i could trim off 20 minutes.
Good Luck to the next guy or gal.
I did the same thing! I was wondering what I was doing wrong.
FYI you don’t need to remove top with many new models. So if you got the machines stacked, no need to lift them
How will you get the upper selector panel off to get access to the screens holding the panel with the door on it?
Great video!! However this is harder than than it looks! This man is a professional and it shows… My first problem was trying to get the new baffle between the drum and the outside cylinder. After 2 hours I gave up and went at it again the next day, took me an hour the second day to get it in place... Use plenty of windex or cleaning solution to lubricate it, it definitely helps.
The second problem was the ring with the spring. It easily took my son and I 10 try’s to get it. Every time the baffle would pull loose.
I have run a load of clothes and no leaks!! Yay!
Next time I will not think twice, and pay a professional!
Steve. Who knows what tomorrow has in store, but today you are my favorite human being.
You are my hero! I was able to do everything on the repair except install the second wire/spring on the front part of the bellow. Using the needle nose pliers that you showed, along with a couple plastic bicycle spanners (normally used for mounting bicycle tires onto rims), I was able to mount that wire/spring and complete the repair. And nothing leaks! Thank you so much for posting this!
Excellent directions. I ran into a problem stretching the bellows to fit. After putting them in the dryer on extra low for 5 minutes, no problem!
Thank you. Couldn't have done this repair without your video! Very clear and straightforward, took us about an hour and 15 minutes.
Wonderful editing and I really appreciate the explicit step-by-step guide. Thank you so much for being there when I needed you today!
Thanks very much. These instructions were spot on. Spring loaded clamp was certainly the hardest part.
Perfect! Everything went perfect! THANK YOU! Also it’s helpful to have someone hold the top of the baffle when tucking in between the drum. Another hint get it wet so it slides in!
Great instructions! My Whirlpool Duet is slightly different but I took pictures as I was taking things apart and was able to get it back together again along with this video. As other have stated, the 2nd spring clamp is a serious pain but with another pair of hands holding and many attempts, I was finally able to get it on. It took me about 2 1/2 hours plus a sanity break while putting the clamp on. Thank you so much, I never would have been able to complete this repair without you.
To bad the first screw to rust is the one behind the soap dispenser and now the head of it is gone.
Thank you for sharing this video! It was very helpful with some great tips. I changed the bellowe in my WFW9050XW00 today and the only difference from the model you did was there was no screw at the bottom (in the centre) of the control panel. The left side screw for the panel it’s a Torx head bit as well for some reason. Great job on the video! Thanks again!
This was very helpful. We replaced our moldy seal with a new one. The one issue we had was the wire assembly for the door lock became unplugged and we didn't realize it before putting all the panels back on. On trying to run a cycle, the light for "door lock" was red but the door would not lock and the cycle did not start. We had to take everything back off to realize our mistake. So I suggest double checking all wire connections before putting everything back together. Took about 2 hrs start to finish, but we basically had to do everything twice.
You have saved me so much money. Thank you!!!!
Steve, this is the 4th how to video I have watched from you. This video and the other three helped me save hundreds of dollars. Thank you so much!!!
The best video explaining the change of the bellow seal for a Whirpool machine. Very helpful, thank you a lot!
Thank you very much, man. I just fixed my washing machine, and it works perfectly. You saved me a few hundred bucks for sure. Big thanks. 👍
Thanks for this video, it helped me a lot. Of course the part does not come with any instruction. One important tip given is the one to use a little soapy water to lube the bellows going in. I needed a second set of hands to get the outer spring clamp on and used two sets of needle nose pliers to spread the spring to get it over it's ridge while my wife held the rest in place. Note: I also did NOT have to remove my dryer from on top of my washer as I got the upper face plate off without doing that. No leaks, we're happy! Thanks again.
You're the Man !!!!Thank You so much. Excellent step by step instructions.
This video helped immensely. It took me a little longer because I had to move my washer out of the room. For the spring loaded front band, I used needle nosed pliers and needle nosed vise grips. The needle nosed vice grips held one side of the spring, while I pulled the other side with the needle nose pliers.
I am doing this job right now and for my Whirlpool WFW9050XW03 It wasnt simple philips screws. 7/64th Allen Key needed for single screw where detergent tray is. T20 Tork Keys needed for 2 screws at door lock aswell
Love the videos that have the wash machine out in an opoen room or even on a turntable, like a diy has this luxury.
Thank you for this. I was able to complete the job in less than an hour after ordering the part from you. The part arrived quickly as well.
Excellent! So glad this video was helpful!
fyi. while you have that bottom panel removed, open that port on the right and clean it out!
Great advice!
Absolutely. It was disgusting.
just be prepared for water
Yay! I got $1.19 in change out of that filter, all coated with the nastiest black gunk you've ever seen.
Opening that up to clean it made me partly wish that I just bought a new washing machine 🤢
This is one of the best explanatory videos for this repair. Thank you so much!!!!
Great how to video. Was dreading doing this but I was done in under an hour. Good tip on lubricating the seal before putting it in. It allows for a small realignment if its not quite right. Thank you.
I've replaced my Whirlpool Duet bellow tub seal 3 times now, every time I need a refresher to build my confidence on the proper process and this video is perfect. Knocked it out in about an hour today. No leaks and I feel good about the replacement. Thank you...saved me money, time, and stress (only had to halt the laundry cycles for 4 days), and completing it on my own. Yes!!
Thanks a bunch. Just followed through this video and completed the replacement on my washer today. Took me an hour and a half doing it the first time.
Amazing. Incredibly helpful.
thanks for the instructions. i didn't have to take off the top panel. this was signifixant as I have mine stacked with dryer. also I use a drill for the screws much speedier.
You're the best! i just scored a great deal on a washer dryer pair because the boot was ripped. Fixed it and it works great! Thanks!
Get the expansion pliers. I didn't. Took me hours to put that spring clamp back on.
STEVE, thank you so much for the detailed instruction. Install was a breeze thanks for you! Thank you thank you thank you.
excellent, well paced and clear pro instructions
Thank you so much. Super nice video and clear description of each steps to perform.
Very good tutorial
Thank you! I replaced mine and saved me $$. Thank you!!!!!
Great video! Thank you!
I’ve order two bellows and they don’t come with the holes at the bottom. I have a WFW9750WW01.
At the 1:53…I have a Whirlpool Duet WFW9750WW01… I don’t see a tab. It appears that screws are holding it in place. Is that the case on this model? Looks difficult to reach those screws.
Hi there. What angle is the piece holding the bottom of the tub set at?
Thank you sir ! Amazing how much money a person can save themselves
Thanks, really helpfull video😀
Thanks. You make it look easy.
Thanks!!! Done and done!! Appreciate it very much!! That last spring seal is a bitch, but if you do it exactly as he does it eventually goes on!! 😹
Glad it was helpful!
Very precise video...It worked like a charm!
How imperative is it to remove the top of the washing machine? I have a stacked washer and dryer so removing the top of the washing machine would mean removing the door to the bathroom and getting 2 guys to come help me lift the dryer out of the bathroom...
I didn't remove the top. Just the screw in the middle top where the door is holding in the panel and the one screw by the dispenser and it popped off the control panel
Do not need to remove top on many models. The control panel just comes off
How did you manage Jennifer?
Im in the same boat. ;//w//;
Thank you so much!
With the repair completed, I'm getting a LF code.
Is there a sensor or a level I should check or replace?
When I turn on a wash cycle, it turns on, the water begins to enter as usual, then after a couple of seconds it trips the electric outlet.
Thank you. Your instructions were spot on.
could not find the ooter tub....
It took like 15 minutes to install the rubber seal. Spring loaded band was the more tricky one . Idk what's so hard everyone is saying. Spray some Windex and tuck the seal in all around
Question: when do you need to replace this seal?
Hi there our gasket clamp for the door portion broke with the spring. Any chance there is a part on part select for it? EXACT SAME washer model.
I am having so much trouble installing the bellow to the lip. Every time I try to slide it on the lip it’s completely come off! Beyond frustrating. Gave up, trying again tomorrow.
Thank you
Just got mine replaced. Is it normal for the door boot seal to hold water? After a wash, there's always water left in the rubber seal.
It should mostly drain through the holes at the 6 o'clock position. I usually have about a tablespoonful of water there which I will wipe out with a rag. If you leave the door open between loads of wash it may evaporate, if you close door with that little bit of water in it, it will get pretty nasty in a day or two.
It is definitely NOT a "really easy job" as you say. In fact, it has been the most frustrating DIY job I've ever undertaken. Getting the bellows to fit and stay put in the slots was a nightmare. To be honest, after three days I'm still trying to get the spring-loaded ring to fit without pulling the bellows off its groove.
So followed the instructions now you can’t turn the inner drum, there is a horrific squeal sound when it try’s to spin and there are rubber shavings from the boot. What in the heck?
GREAT HELP !
I bought the replacement part for model wfw9250ww00. I called whirlpool for the item number. I was told it's w10290499. I went on eBay to buy the replacement. we tried every way to put it in and just wont go in. I have a feeling that we were sent the wrong below. Is there a way you can show us how the right below looks like? I already broke nails by trying to put the replacement in. Even my husband has given up and went to sleep.
Hello, when researching your Whirlpool model number the part # W10290499 was the original part for your model. Unfortunately, Whirlpool has discontinued the part and has made a substitution part #WPW10381562. If the part is not fitting correctly I would suggest to contacting the manufacture directly to see if they have one closest to the original that will fit and work properly for your model.
thank you for replying. I've hired another repairman to put it in for us. it worked...
I have a Maytag and it's design exactly the same.
I can't seem to get the inner band in the v-groove. It seems to be too small but I know it's not because I took it off myself. I unloosen the screw to it's Limit still want fit. Can anyone help me.
100% helpful. Thank you.
I managed to do it without removing the front
my whirlpool washer does not have bottom access panel
Thank you so much for sharing. I just change it.
The shirt lets me know that this guy knows that he is doing.
Where can I get the bellow in Toronto, any ideas?
I have this error, which can be, E1 F6
Thank you very much sir!
If you're reading this and can't get the bellows to tuck in because it's too small. Flip it around. The way he puts it in is extremely confusing and misleading. The wider part should be going into the machine. I just wasted 2 hours pulling my hair out.
Thank you !
Thank You for the video... 😐👍
You're very welcome! Thanks for watching!
Perfect!
Another great technique-buy a top loader! Way better.
the voice is very difficult to hear
It's easier to endure a root canal than it is to put the metal ring back around the door boot! Please redo this video without the monotonous guitar in the background!!
I'll never buy a front loader ever ever ever ever ever ever ever ever ever ever ever ever ever ever ever ever again
THIS IS NOT EASY AND WHIRLPOOL IS GARBAGE
Maybe try less cocaine? >•