I'm really impressed with this build. I can tell a lot of thought time and effort went into the build itself. The rustler is one of my favorite RC's it makes me want to go do it to one of mine tomorrow
🧏♂️Pro tip.. (I run the same transmission cases, similar motor + gearing, but) ..Use 2 motor plates not 1. Install both together Using longer screws, & I like to put a screw w.Lock Nut in the top gear cover mount hole instead of putting the gear cover on.*Cover wont fit over the 34t pinion anyways. **I know this info is about 5years to late, but it is what it is, & I cant change that.. Far as i know there's no single motor plate available for Traxxas 2wd truck that won't bend when using any 100mph+ capable motor, or is there any video's on CZcams showing this helpful info, so be the first one. Ps; another way to achieve the double motor plate for less money is to purchase the RPM trans. Cases and use that motor plate on the original stock Traxxas plastic cases. Bolts right on and honestly wrks little better, but not as much clearance can be made for bigger motors that require so much room you have to file down the two corners of the cases where the motor contacts. And don't forget to adjust the motor end cap on the shaft side only over to next set of holes to have the motor wires going to the ESC pointed inward. That way they. Don't get damaged after flipping over backwards or sliding around backwards into a curb. Use Traxxas HDuty spur-gear shaft, Robinson racing idler gear, HR HDuty dif locker and dif case, proper shim the dif and spur shaft so no side to side movement but not binding when spinning transmission by hand. Hope that helps ya get over 100mph. I know it can be done. (128pb on 6s CNHL bat, stock chassis & body, GRP's, XLX esc, Castle 1515-2200kv, 34/34)
That’s a nice rustler man lol. I’m planning on doing this type of thing with my xl-5 brushed rustler that I had emptied all the electronics and stock remote from and sold off. I even sold off the stock wheels for it. I’m attempting 80-125 mph with that rustler on 3-5S lipo power and about 130-145 on 6S. That’s the goal once I get one of these huge 1/8 Th scale combos for it. 34/34 gearing or 34/30 if I could do that. Going to go with s Futaba remote as well. By the way where do I buy gears like this at ?..... what brand are they ?I got mod 1 25 pinion and mod 1 40 spur inside my Traxxas E Revo 1/8th Mamba Monster 2200 KV truggy and I think on 6S I’m easily at 83-90 mph.
@@henryescobar6739 I actually haven’t even built a 1/10th stadium truck Speed run car yet lol……. I’ve opted for a Traxxas Rustler 4x4 Vxl instead. I’ve sold my older cars but I am planning on rebuying one or two more cars. Either a rustler 2wd brushed or a bandit brushed but I’ll be putting in 1/8th scale electronics into them.I’m still in the process of wanting to build one like when I saw that guy Draven on CZcams who had a couple or three of them at least.
Aluminum is soo sick but when you crash everything bends and gets wacked outta place some parts are great for Aluminum but plastic is better for crashing rpm is great it just snaps back into place when you crash
I have a rustler 2wd and 2200kv with sidewinder8 my gearing is 33/36 I have grp tires why when I pull throttle my rustler seems to be spinning out like doing donuts?? Am I hitting the throttle to hard am I supposed so lightly hit throttle slowly till it starts to gain speed?
@@IKillzZzombies yeah I just started mine but went with a smaller motor. I'm having trouble keeping mine on the ground. 46mph and it lifts and does ballet crap.
How much did the whole car cost you not to remote control but just the card self to get a 100 miles an hour with everything on it tires wheels everything and my guessing about a $1000 I'm just taking a guess
Don't see why everyone is running mamba's. Let's see a stock rustler hit a 100. I'm running a vxl 3s system and I 100 easily. Some minor modifications and it's easy. And no those camber links aren't for the Stampede they are for the Rustler bandit and stampede. Could be another one but yeah
You can't just do show and tell . COM'ON man you've got to drive that sucker.
I'm really impressed with this build. I can tell a lot of thought time and effort went into the build itself. The rustler is one of my favorite RC's it makes me want to go do it to one of mine tomorrow
Lets see it run!
🧏♂️Pro tip..
(I run the same transmission cases, similar motor + gearing, but)
..Use 2 motor plates not 1.
Install both together Using longer screws, & I like to put a screw w.Lock Nut in the top gear cover mount hole instead of putting the gear cover on.*Cover wont fit over the 34t pinion anyways.
**I know this info is about 5years to late, but it is what it is, & I cant change that..
Far as i know there's no single motor plate available for Traxxas 2wd truck that won't bend when using any 100mph+ capable motor, or is there any video's on CZcams showing this helpful info, so be the first one.
Ps; another way to achieve the double motor plate for less money is to purchase the RPM trans. Cases and use that motor plate on the original stock Traxxas plastic cases. Bolts right on and honestly wrks little better, but not as much clearance can be made for bigger motors that require so much room you have to file down the two corners of the cases where the motor contacts. And don't forget to adjust the motor end cap on the shaft side only over to next set of holes to have the motor wires going to the ESC pointed inward. That way they. Don't get damaged after flipping over backwards or sliding around backwards into a curb. Use Traxxas HDuty spur-gear shaft, Robinson racing idler gear, HR HDuty dif locker and dif case, proper shim the dif and spur shaft so no side to side movement but not binding when spinning transmission by hand.
Hope that helps ya get over 100mph. I know it can be done. (128pb on 6s CNHL bat, stock chassis & body, GRP's, XLX esc, Castle 1515-2200kv, 34/34)
That’s a nice rustler man lol. I’m planning on doing this type of thing with my xl-5 brushed rustler that I had emptied all the electronics and stock remote from and sold off. I even sold off the stock wheels for it. I’m attempting 80-125 mph with that rustler on 3-5S lipo power and about 130-145 on 6S. That’s the goal once I get one of these huge 1/8 Th scale combos for it. 34/34 gearing or 34/30 if I could do that. Going to go with s Futaba remote as well. By the way where do I buy gears like this at ?..... what brand are they ?I got mod 1 25 pinion and mod 1 40 spur inside my Traxxas E Revo 1/8th Mamba Monster 2200 KV truggy and I think on 6S I’m easily at 83-90 mph.
You can find the gears on ebay
Did it work
@@henryescobar6739 I actually haven’t even built a 1/10th stadium truck Speed run car yet lol……. I’ve opted for a Traxxas Rustler 4x4 Vxl instead. I’ve sold my older cars but I am planning on rebuying one or two more cars. Either a rustler 2wd brushed or a bandit brushed but I’ll be putting in 1/8th scale electronics into them.I’m still in the process of wanting to build one like when I saw that guy Draven on CZcams who had a couple or three of them at least.
@@gorillabeartech4577 nice
The full aluminum build looks amazing
Another year would be dope to see it run happy New Years
Amazing
I need a tutorial or parts list replacing spur.
Nice setup I got the same color edition rustler just threw my 1512 1800kv blx 185 esc spooled geared now just waiting on my 17mm adapters 😈😈😈
I thought the 2200kv motor I put in my stampede 2wd was big but that castle motor looks monstrous
Nice set up
Aluminum is soo sick but when you crash everything bends and gets wacked outta place some parts are great for Aluminum but plastic is better for crashing rpm is great it just snaps back into place when you crash
Great build man. This is what But a bit much much aluminum for me my rustler is a simp for curbs 😂😂😂😂
Where did you get the pinion and spur gear?
I've got setups similar to this and other speed monsters and if u can keep it on thr ground it will do more than 100. My 1415 did 114 on 6s...
I have a rustler 2wd and 2200kv with sidewinder8 my gearing is 33/36 I have grp tires why when I pull throttle my rustler seems to be spinning out like doing donuts?? Am I hitting the throttle to hard am I supposed so lightly hit throttle slowly till it starts to gain speed?
That’s awesome
Sick build 👌🏼
Want to sell it to me bro?? Or do u got a parts list??
I bet it costs a crap ton to make
Skipp Dunlap yup
500$
@@FunkyPhilMusic lol no. Im $800 deep not including the truck and ive still got more to do
@@IKillzZzombies yeah I just started mine but went with a smaller motor. I'm having trouble keeping mine on the ground. 46mph and it lifts and does ballet crap.
Wat gears with I use for drag 2050kv motor sidewinder 8 esc
Nice!!!👍👍
How much weight is that??
Sweet have mine coming thats what i wanna do to it im going to try 70+ AND IDEAS FOR THAT
Can I get a parts list and maybe links I’m trying to get my rustler to this !
Hi what kind the tires you put in there and what the name I like this tires I trying to go buy thank you
That is cool 👍👍
34_34 ? ½ Ratio?
No over heating?
Or puffin brand new after new lipos? I need to know.
It's probably really close to overheating in 1 run. Wouldn't want to do much more than that. I'm just speaking from previous vids I've seen.
Where'd you get the tires?
What wheels
If ur running 34/34 what did u need and could it work on a 3800kv and can I get links of everything u used did u need a adapter for that spur gear?
I had to drill an extra hole in the motor plate
No adapter but idk about the 3800kv
MAVE_____RICK what speed do u get with those gearing I’m running 3s
@RIDEROFTHESTORM 5150 A rustler?
How do you get to 3434 to fit on a Hr transmission. I’m running 3430 cause I can’t seem to get it to fit
What spur and pinion u running
Integy 34t spur and mod1 34t pinion from a e revo
@@MAVE_RlCK awesome. Thanks. In process of building my first speed run rustler. Any tips for me?
@@MAVE_RlCK How did you choose that gearing?
I am a little late to the party, but why would you add a bunch of weight to the car when you can just get a wheelie bar?
Even with a wheelie bar when you are going that fast, it’s not enough
Tyler’s?
How much did the whole car cost you not to remote control but just the card self to get a 100 miles an hour with everything on it tires wheels everything and my guessing about a $1000 I'm just taking a guess
Around $500
Sorry yes the whole car was about $1000
@@MAVE_RlCK 500 is way to cheap, the motor alone and the batteries are already expensive
Oh ok 1000
@@MAVE_RlCK did u buy a stock rustler then swap parts?
I have the s4 compound tires and cant get ANY traction. I want to know if you do with yours or if I got an old set or bad set.
Try adding weight but yes mine still spin
@@MAVE_RlCK I have a bunch of added stick on wheel weights. I might try the s1 compound
Tire name?
Let me see it run
Plastick is stronger and it dont bend for 500$ less you can run 115 and tires are bad not for street top end
Don't see why everyone is running mamba's. Let's see a stock rustler hit a 100. I'm running a vxl 3s system and I 100 easily. Some minor modifications and it's easy. And no those camber links aren't for the Stampede they are for the Rustler bandit and stampede. Could be another one but yeah
Right on man
What’s does your build look like..
Brad
Let’s see a pass
There's no way this car going 100 mph
Not much of that is still rustler lol