⚡️ WATCH NEXT 🛴 Varla Eagle One full review bit.ly/36ReR8Q 🛴 Varla Eagle One rugged clamp upgrade bit.ly/3zXe8PV 🛴 6 Maintenance Tips For Your Varla (Zero10x) bit.ly/3Boeks8
Hi dude loved your gripes about the Varla egal one, I’m trying to by one from Varla but they have said they are not shipping outside the states 😢 I live in Wales, how did you buy yours?? Thanks Adam
there is a problem with my varla where there is a red exclamation point, brake lights flashing without me using the brakes, and throttle not working. I tried pumping the brakes and checking the wiring and nothing works, how can I fix this?
Yeah about that... I have a monorim suspension installed and I accidentally stripped the bolt that makes the fender stable instead of it going up/down ;/... Update I am going to get a monorim back suspension ..
Better with the fenders removed completely. Makes it easier to clean and don't go thru much water and mud anyway. Upgraded post clamp looks better turned 180 degrees as well. Functions fine and I ride full tilt.
I disagree but if you live in a dry country mostly, then no need. But for others, it’s essential. As for performance, a mudguard has nothing to do with it. That comes down to tyre pressure, hills, wind, weight, p-settings, temperature, stance and battery state.
Hi! I don’t get any wobbles myself but I think it’s definitely good to have in general. Check your tyre pressure just in case. I would definitely like the steering stiffer regardless. Stay safe man! 🤛🏻
It depends how stiff is your stearing. My came so hard that I cannot turn it with one hand in the middle. But I got used to it and ofcourse absolutely no wobble.
Got three for Christmas, two of them have a flat front tire after one use! Any recommendations on alternative tires or solutions, seems outrageous? Had checked the tire pressure was between recommended 40-50 psi as well because it was the first ride. Also one other them the brakes just straight up don't work, I'm pretty sure it needs to be bled because I see the hydrolics somewhat close, but not all the way. Some nails and parts came rusted and the screen that displays speed came with a chip in it:(... Very disappointed
Hi! The stock tyres are ok but it’s best to upgrade them. Link below. I have mine at 50psi and no issues. The surface rust you are talking about sounds like the hydraulic fluid, leaked, causing the brakes not to be effective. You should be able to replace the rusted screws easily. Or contact Varla and get them sent out. Best to bleed the brakes obviously. There is a kit you can buy for this on Amazon. Here are those tyres. Street, hybrid or full off-road. I have the street, but have not fitted them yet. Shop around for prices a.aliexpress.com/_mrxq9yU
Hello my friend... I was watching your videos and just wanted to share that the helmet you're wearing is not rated for motorized vehicles. I know this because I bought, and returned, the same helmet. Indeed, it's a great helmet because it's light and has plenty of airflow, but it clearly says it's not rated for motorized vehicles. I just wanted to share that information with you in case you weren't aware. I was able to get a very good full face motorcycle helmet for far cheaper (that helmet you have is pretty expensive!). If you want me to share the link to the helmet I got, I'll be happy to do so.... I just didn't include it now because I didn't want to come across as pushing someone's product on your channel. I hope you don't mind me sharing this with you. As a fellow rider, just wanted to look out for you, and my heart is in the right place 😊
Hi man! The Bell helmet I use has MIPS (of course) plus breakaway screws, X-Static® and XT-2® Padding,. The general use is all-Mountain, downhill, MTB and free riding. It wasn’t expensive at all. These are popular because of the good visibility and they are light. Heavier helmets I don’t like because they can restrict your movements and the visibility ain’t good. Thanks for the comment however. I’m always upgrading my gear so I’m always looking out for new products. You are more than welcome to share your link ⚡️
I have Eagle one pro Can you tell me how to lose break it’s to tight I just purchased recently I tried to follow Manual but I couldn’t figure out how to lose the breaks it’s so hard and stopped bike right away and it’s bit risky this why
Hydraulic brakes on the Pro? You’ll need to bleed them until you are happy. I’ve not made a video on this yet but click here for further help czcams.com/video/knTVicVjT7k/video.html
Little piece of Gorilla tape will protect the cable in that spot bro :) Do the regen brakes come on only when you pull the brake or when you release throttle??? i get nothing when I release throttle only???
Hi Jersey! I’ve since used Gorilla Tape and silicone. No issues. But my front controller did blow a while back so the scooter is down at the moment (made a video on that) Either releasing of the brake/throttle activates the regen. I have mine on level 2 p-setting from what I remember.
What pressure you have in them? Make sure that there is no sharp edges on the tyre also. Most people upgrade the tyres because the stock ones ain’t the best. Click here to look at tyre options a.aliexpress.com/_EyErsaP
I just received my new Eagle One and was upset to find there is a detent in the steering that causes the front wheel to pop into a straight ahead attitude. This is very annoying when trying to navigate at slow speeds because it keeps popping into this detent. Is this a standard feature why have I not seen one person mention it in any of the dozens of videos on this scooter? Also, is there anyway to disable it?
Hi Gary. This is perfectly normal. You will not notice it after a while. It's basically to keep the steering straight. It's helpful at driving high speeds
To be honest, best to replace. It would have created a weak point and would be dangerous. You can try Aliexpress for them. Macury store is quite popular ⚡️
@@Movelectrics can you let me know how it go asap because I'm debating on varla eagle one or the new Ariel Rider Kepler I'm real conflicted on which to get I live in Florida living setup is a second floor apartment and it rain 🌧 a lot here. So I need good fenders hopefully if it get caught by rain puddle it won't destroy my unit ?
@@Movelectrics i don't understand when u mean extended with that tape ? Can you show a pic how it looks How did your controller stop working a unit failure or going overboard with the scooter...
Join my FB group and I can show you what I mean with the Gorilla Tape (linked below) Also this video explains what happened with the controller czcams.com/video/pT-QYTorDRM/video.html FB bit.ly/2NMeXIY
Have to add washers to the fender and brake cables sticking out waiting to be cut by a tree or your own fender? This thing Costs more then $2200 and these issues show me they are way overpriced $$ glad I decided against one.
⚡️ WATCH NEXT
🛴 Varla Eagle One full review
bit.ly/36ReR8Q
🛴 Varla Eagle One rugged clamp upgrade
bit.ly/3zXe8PV
🛴 6 Maintenance Tips For Your Varla (Zero10x)
bit.ly/3Boeks8
T-27 is a torx bit. Hex bits are allen wrenches.
@@stuwest5862 spot on! T27 torx ⚡️
Hi dude loved your gripes about the Varla egal one, I’m trying to by one from Varla but they have said they are not shipping outside the states 😢 I live in Wales, how did you buy yours??
Thanks Adam
Hi
I’m in the EU. Here is that site eu.varlascooter.com/?sld=3
I thought I heard an Irish accident.. they don’t have an option to ship to the UK 😤 I really want to buy one in time for Christmas 😢
Keep an eye on that small screw on the clamp it does get loss in time.
Thanks for sharing Robert!
Thanks for the tips, like the washer idea, but maybe go with black washers so,they don’t look cheap,or stand out…
Doesn’t bother me really to be honest but work perfect ⚡️
there is a problem with my varla where there is a red exclamation point, brake lights flashing without me using the brakes, and throttle not working. I tried pumping the brakes and checking the wiring and nothing works, how can I fix this?
Sounds like a sensor issue perhaps. Join the Zero10x owners club FB group and ask there. They are very helpful!
Definitely the sensor I had the same problem it's the wire above the brake line. Mine had dirt in it take out with small wrench 🔧 and clean.
Yeah about that... I have a monorim suspension installed and I accidentally stripped the bolt that makes the fender stable instead of it going up/down ;/... Update I am going to get a monorim back suspension ..
Hi! I’m sure you could get the bolt in a hardware store ⚡️
Better with the fenders removed completely. Makes it easier to clean and don't go thru much water and mud anyway.
Upgraded post clamp looks better turned 180 degrees as well. Functions fine and I ride full tilt.
Where i live. I need the fenders. Couple of washers where the screws are firms them up.
I disagree but if you live in a dry country mostly, then no need. But for others, it’s essential.
As for performance, a mudguard has nothing to do with it.
That comes down to tyre pressure, hills, wind, weight, p-settings, temperature, stance and battery state.
thanks! I had a speed wobble today around 40-50k. So it does need a damper.
Hi! I don’t get any wobbles myself but I think it’s definitely good to have in general. Check your tyre pressure just in case. I would definitely like the steering stiffer regardless. Stay safe man! 🤛🏻
It depends how stiff is your stearing. My came so hard that I cannot turn it with one hand in the middle. But I got used to it and ofcourse absolutely no wobble.
Got three for Christmas, two of them have a flat front tire after one use! Any recommendations on alternative tires or solutions, seems outrageous? Had checked the tire pressure was between recommended 40-50 psi as well because it was the first ride. Also one other them the brakes just straight up don't work, I'm pretty sure it needs to be bled because I see the hydrolics somewhat close, but not all the way. Some nails and parts came rusted and the screen that displays speed came with a chip in it:(... Very disappointed
Hi! The stock tyres are ok but it’s best to upgrade them. Link below. I have mine at 50psi and no issues. The surface rust you are talking about sounds like the hydraulic fluid, leaked, causing the brakes not to be effective. You should be able to replace the rusted screws easily. Or contact Varla and get them sent out.
Best to bleed the brakes obviously. There is a kit you can buy for this on Amazon.
Here are those tyres. Street, hybrid or full off-road. I have the street, but have not fitted them yet. Shop around for prices
a.aliexpress.com/_mrxq9yU
One MAJOR fix would be to get solid tires... I got two flats going 13 mph on the street in less than 100 miles of riding...
Solid tyres in my own experience are very bad depending on what type. Main thing is to keep your psi topped up to 50 ⚡️
@@Movelectrics They were...
i have 745 km on my mantis 10 and i havnt had a flat yet all i do is check my tyre pressure everytime i use it to make sure i can't get a pinch flat
Hello my friend... I was watching your videos and just wanted to share that the helmet you're wearing is not rated for motorized vehicles. I know this because I bought, and returned, the same helmet. Indeed, it's a great helmet because it's light and has plenty of airflow, but it clearly says it's not rated for motorized vehicles. I just wanted to share that information with you in case you weren't aware. I was able to get a very good full face motorcycle helmet for far cheaper (that helmet you have is pretty expensive!). If you want me to share the link to the helmet I got, I'll be happy to do so.... I just didn't include it now because I didn't want to come across as pushing someone's product on your channel. I hope you don't mind me sharing this with you. As a fellow rider, just wanted to look out for you, and my heart is in the right place 😊
Hi man! The Bell helmet I use has MIPS (of course) plus breakaway screws, X-Static® and XT-2® Padding,. The general use is all-Mountain, downhill, MTB and free riding.
It wasn’t expensive at all. These are popular because of the good visibility and they are light. Heavier helmets I don’t like because they can restrict your movements and the visibility ain’t good.
Thanks for the comment however. I’m always upgrading my gear so I’m always looking out for new products. You are more than welcome to share your link ⚡️
@@Movelectrics Sounds good brother. Be safe and have fun!
@@fpvflyer4758 send the link man. I like to always check out new gear 🤛🏻
I have Eagle one pro Can you tell me how to lose break it’s to tight I just purchased recently I tried to follow Manual but I couldn’t figure out how to lose the breaks it’s so hard and stopped bike right away and it’s bit risky this why
Hydraulic brakes on the Pro? You’ll need to bleed them until you are happy. I’ve not made a video on this yet but click here for further help czcams.com/video/knTVicVjT7k/video.html
fabulous video...washers...awesome idea :) :) don't be stripping the screws :) :)
It always the screws on these! 🛴
My right brake (under throttle) doesn’t work and this is just after the 2nd ride. Any tips on what I can do to adjust the brake?
Sounds like you need to bleed the brakes. Watch this video czcams.com/video/ALSBwMlPKP0/video.html
@@Movelectrics Thank You!
Thanks for sharing 👍 😊 the tips!
No problem Craig!
Little piece of Gorilla tape will protect the cable in that spot bro :)
Do the regen brakes come on only when you pull the brake or when you release throttle???
i get nothing when I release throttle only???
Hi Jersey! I’ve since used Gorilla Tape and silicone. No issues. But my front controller did blow a while back so the scooter is down at the moment (made a video on that)
Either releasing of the brake/throttle activates the regen. I have mine on level 2 p-setting from what I remember.
I think you have to turn on the regen in settings or you can at least adjust the regen settings
@@dswartley100 Mine only regens with brake deflection not throttle release.Going on 800 miles.
I’ve went though 6 flat tires already and have had the Varla eagle one for 7 weeks so far :(
What pressure you have in them? Make sure that there is no sharp edges on the tyre also.
Most people upgrade the tyres because the stock ones ain’t the best.
Click here to look at tyre options
a.aliexpress.com/_EyErsaP
What’s difference between Varla eagle one and Zero 10x
Exact same but different labels. Zero10x though comes in higher volts and Ah batteries.
I just received my new Eagle One and was upset to find there is a detent in the steering that causes the front wheel to pop into a straight ahead attitude. This is very annoying when trying to navigate at slow speeds because it keeps popping into this detent. Is this a standard feature why have I not seen one person mention it in any of the dozens of videos on this scooter? Also, is there anyway to disable it?
Hi Gary. This is perfectly normal. You will not notice it after a while. It's basically to keep the steering straight. It's helpful at driving high speeds
Where did you get a clear case for the Speedometer
Got it from Banggood but i think AliExpress have them now.
Bent my Eagle One stem; any ideas about straightening it?
To be honest, best to replace. It would have created a weak point and would be dangerous.
You can try Aliexpress for them. Macury store is quite popular ⚡️
I hear the fenders not good because water still hit your back is it true
This is true. All I did was use some gorilla tape as an extender. I have however just bought the correct extender, I will fit and see how that goes ⚡️
@@Movelectrics can you let me know how it go asap because I'm debating on varla eagle one or the new Ariel Rider Kepler I'm real conflicted on which to get
I live in Florida living setup is a second floor apartment and it rain 🌧 a lot here. So I need good fenders hopefully if it get caught by rain puddle it won't destroy my unit ?
My Eagle One is currently down at the moment with a blown controller. You could use Gorilla Tape as an extension.
@@Movelectrics i don't understand when u mean extended with that tape ?
Can you show a pic how it looks
How did your controller stop working a unit failure or going overboard with the scooter...
Join my FB group and I can show you what I mean with the Gorilla Tape (linked below)
Also this video explains what happened with the controller czcams.com/video/pT-QYTorDRM/video.html
FB bit.ly/2NMeXIY
Isnt the speed limit like 20 kmph where u live? Ive wanted 2 get it but where on earth can u drive these monsters really
I test the scooters on closed grounds ⚡️
Y’all follow the laws?
With these scooters, they are great for off-roading on private land.
Have to add washers to the fender and brake cables sticking out waiting to be cut by a tree or your own fender? This thing Costs more then $2200 and these issues show me they are way overpriced $$ glad I decided against one.
Washer takes minutes to do and a simple cable tie just to stop them from being snagged. Easy job. By the way, this scooter is $1700 below. Not $2200.
@@Movelectrics Thin discs that bend and brakes that have never worked well are not maintenance issues but QC issues
What did he say?
Hi
What do you mean? If you can’t understand my accent, you can use the subtitles that may help