Fix the Boot problem on QNAP TS-x51 and TS-x53 NAS. This video has been updated with the ENGLISH SUBTITLES. You can download the connector diagram here: www.threshold-lovers.com/down...
You are welcome: I did face the same problem than you, with the same level of stress, so I was sure this wideo and diagram will help a lot of people ... Enjoy !
I already was looking for a replacement of my QNAP TS-851 when I saw this fix. I thought the MB was dead but the described symptoms matched mine exactly. So thanks for a solution that cost me about 5 cents. Many thanks to you....
Thanks so much for posting this way back in 2021! I have brought my 6-yo+ NAS back to life with a 100ohm resistor and some very amateur soldering. Really appreciate you posting this so we could all work through it.
My pleasure: the number of persons that have save their NAS with this solution, is countless ! Do not forget that this should not be taken has a permanent fix: there is a deep problem with these CPUs and, sooner or later, the NAS will die forever ! Save your data in another place if you continue to use it...
Thank you!! Had a hard time tracking down a 100 ohm resistor locally but eventually found one. Attached it to pin 1 and 8 and it booted right up. Amazing!! You bought me some time to replace this heap of crap. Cheers!
Good news ! that is the purpose of this fix ! My NAS has been fixed for months and it is still running perfectly ! nobody knows how long a NAS will continue to run after this fix, but based on what I have read, it is many months...
Thank you Rob : I am very happy to see that you get out of the trouble ! One more NAS saved... Yes it is amazing because there are a lot of persons havind this problem, and since I have made this video, thousands of peopla have fixed their boot problem using this method ! Have a nice Christmas !
You are welcome: one more NAS saved !! I have been told that you can increase the resistor value up to 430 ohms, with the benefit to reduce the current (Amps) flowing through the faulty part, and therefore increasing the life time of the repaired device. Bur I have not yet tested !
J’avais ça: Status = OFF, USB = BLUE, LAN = clignote / sur un TS 651. Merci à toi pour ce partage! Tu viens de me faire économiser une somme. Avec de la gaine thermique c’est très propre. Et surtout le NAS fonctionne parfaitement. Je sauvegarde tout et me fait une routine de sauvegarde sur d’autres disques avant que mon NAS soit plus bas que terre.
Heureux pour vous, un NAS de plus sauvé de la benne ! jene les compte plus ! N'oubliez pas de faire un backup complet de vos données, car cette solution ne vous met pas à l'abri d'une panne définitive (le défaut du processeur existant toujours)....
I am happy for you ! one more user and NAS saved ! Do not forget that it is supposed to be a temporarily fix only: the NAS is supposed to die in the future... Mine has been working for months and is still OK... But do not forget to backyp your data !
I am happy that my video has helped you : one more NAS saved !.... Mine has been saved by doing this and it has heen running back like a charm for more than 1 year...
Keep us posted: in 99% of the case, this fix solves the problem ! I had found a few explanations on the problem on the Web but I had not found the diagram: so I was sure that this diagram would be helpful !!
Thanks i have a TS 451 . I tried a 120 ohm resistor on pin 1 and 8 did not work. I used a 100 ohms . Works perfectly . I was able to recovered almost 25 gb from it . Thanks to everyone
Can it be normal that both measurements of pin 1-8 and pin 1-6 are equally low? I am measuring on both Pin 1-6 and 1-8 around -0,05V. This seems to indicate per your diagram that I need a resistor of 100 Ohm between pin 1 and 6, as it is
What size crimp are you using? I see it's a 28-20 AWG. From what I understand the female connector is 2.54mm does that matter? Or is the smaller crimp sizes just to be able to crimp the pin to the resistor legs?
You are wrong on several aspects: -the "2.54mm" value that you mention, is the distance between 2 male pins. This 2.54mm is a standard value for the Printed Circuit Boards hole distance, in which the male pins are soldered. These male pins can be the Dupont male pins (like the ones I show in the video) or another standardized category, such as the KF2510 male connectors that also fit in the PCB holes having the usual 2.54mm spacement. -The crimp size is written on a crimp tool, and relates to the diameter of the cable that will be crimped into the female connector: it does not relates to the distance between 2 PCB holes. When I crimp a cable (or a resistor) in a Dupont female connector, I use the 1.3mm position on my crimp tool. Hope this helps !
Yessss ! I am very happy for you ! Mine died definitely last week, but it has been running approximately 2 years more with this fix ! Do not forget that a NAS always need a backup, and sooner or later, your NAS (with this fix) will definitely die... Enjoy !
@@AlexNoise Yes, it is for sale since yesterday (!), as a spare parts unit ! I do not need it anymore since I have bought another 8-bays NAS as my main NAS, and since I have re-organized all my backup plan to another 4-bays NAS that should be convenient for the backups ...
@@elodiecemoi3057 Data retrieved 🎉!!! New Synology on order, probably going to do a more permanent solder job and then sell it for peanuts on ebay. Do you have a tip jar?
@@EdGriebel Sorry for my unperfect Englis: what do you mean by "tip jar" ??? I have ordered a Synology too (an 8 bays DS1821+), not because they are better than the QNAPs (both QNAP and Syno have had this issue, as every other manufacturer using this faulty serie of Intel processors) but because thay have the SHR-2/BTRFS technology that allow to mix more easily the disks with different capacities. Feel free to ask if you have another question
You are welcome : I am happy to see that my video has saved the NAS of so many persons !!😇 Mine died last week, this time both all the dsks got the red status LED... I believe that this serie was not the best of QNAP
Hi, is this the workaround fix for the Intel Apollo Lake CPU dying issue? I just got my hands on a used TS453be without reading on the CPU issues in advance, so if it is this easy to fix it I might keep it.
I believe it is, but remember that this fix is not a permanent fix: the CPU will die sooner or later (this is 100% sure) because of their faulty design. Mine has been operational 2 years after this fix, but finally died.
Hi, I also have a problem with a model nose: qnap TS-415 white. After the LEDs on the hard drive were all red and the LED on the system was off. The first time the fan started, but I couldn't find it on the network, after several searches I noticed that it was a problem on the motherboard. I searched the internet and found that I had to unplug it, connect a 100 ohm transistor or resistor between two pins, I did that, I connected the 100 ohm resistor between pin 1 and 8. After I restarted the NAS, only the problem from the LED u from the hard drive disappeared, that is, it was seen in green only at slot 1 on the hard drive where I had one placed but still the status LED is off and not booting. What else can I do for them?
I just see your question now, so sorry for the delay. The 100 ohm (or preferabily more for long term reliability) is a fix that works in 99% of the cases, by setting the clock voltage back to an acceptable value (soo the clock signal is back). But in some cases, the 2 junctions of the (internal) transistor are both faulty, and in that case the 100 resistor can't fix the problem. I am not aware of any solution in that case, maybe you can search on the web, but I know that there are similar issues that can't be solved....
@@elodiecemoi3057 Unfortunatly, same Led result here with TS-453 Pro The voltage between pin 1 and 8 was -2.435V so I bought a 100Ohm Resistor (1/4 W) like it was explained. With the 100ohm resistor, the voltage is -1.523V but it seems we have to obtain -1.7V so probably I have to use another value of resistor but I don't know which value I have to buy. Could you help me or tell me if it's a good idea to persist ?
One more NAS saved ! I don't know how to proceed, but I would be veru interested to know how many NASes have been saved by this solution !! If somebody know how to do... Enjoy !!
Hello, Sorry but my website has been totally hacked and is out of order ! You can download the diagram directly from my coud here: mega.nz/file/Quh2xZRb#p4cLG2MuAzYr05nSffNhLuQ8dxVRssUMTrVyyXIRZOY Good lick
Merci beaucoup ! cette astuce a ressuscité mon TS-853 PRO ! Petite précision sur mon modèle, il n'y a pas de connecteur et j'ai été obligé de souder directement Thank you so much ! this trick has revived my TS-853 PRO! Small clarification on my model, there is no connector and I had to solder directly on it
@@elodiecemoi3057 Pareil, Pas de connecteur, directement soudé sur la carte mère de mon TS-453 Pro mais pour moi, pas de résultat probant :( Avant soudage de la résistance de 100Ohm (1/4W), la tension était de -2.435V et après de -1.523V alors qu'on devrait semble t il obtenir -1.7v. Peut être qu'avec une autre valeur de résistance ça pourrait fonctionner mais je ne sais pas calculer la valeur nécessaire malheureusement :(
Après différents tests avec des résistance de valeur différentes, j'ai réussi à obtenir la valeur de 1.706v avec une résistance de 140ohm 1/4w mais malheureusement ça ne fonctionne pas la led status reste éteinte, la led usb est bleu, la led du 1er disque dur est verte et les autres disques dur rouge, pas de bip,.. I did some other tests with differents values of resistor and at the end, with a resistor of 140ohm 1/4w, i can obtain -1.706v But same result, it doesn't to boot, no bip... only usb leb in blue, green led of the 1st HDD and the others HDD are Red... Sad :(
Super utile merci de partager ce genre de tutoriel ! J'ai un TS-251+ qui n'a pas encore (!) lâché. Juste pour comprendre à 100% le jour où cela arrivera et si la réparation par la résistance 100 Ohm échoue je pourrai quand même récupérer mes données en utilisant un autre NAS QNAP en insérant "simplement" mes disques durs dans un autre NAS ? Ou pas :( :( ??
C'est possible mais pas tous les NAS pourront récupérer les disques de votre TS-251+ : sur le site de QNAP l'info s'y trouve peut-être, mais le mieux est de contacter le Support QNAP en leur disant que "vous n'êtes pas satisfait du tout, que vous voulez un modèle capable de relire les disques de votre TS-251, et que s'ils ne vous proposent pas une remise vous passez chez Synology". La plupart du temps ils vous proposent 20% sur un nouveau NAS capable de relire vos disques. Rassurez-vous, ceux qui ont des problèmes avec Synology font la même chose en sens inverse ! Personnellement, j'ai à la fois du QNAP et du Synology...
I'm hoping this will work on my 653B. It's been sitting in a box after it gave the red light of doom and I invested the $350 QNAP wanted into a TVS-672N instead. I have a use for the 653B again and hopefully this will work. I'll report back!
Heureux pour vous ! Avec plus de 37.000 vues, je ne compte plus le nombre d'utilisateurs en détresse ainsi sauvés, et de NAS qui sont revenus à la vie ! Je ne pensais pas que ma solution serait aussi utile 👍👍
hello everybody I have a ts-451 i tried that fix using a resistor 120ohm 2w but i did not work. could anyone tell me exactly what resistor i will need to buy? please
Non: la résistance doit rester en place, puisque c'est elle qui permet de générer à nouveau une fréquence d'horloge correcte. Mon NAS ainsi réparé a fonctionné parfaitement pendant 2 ans, mais maintenant c'est sa carte réseau qui est morte...donc il va finir à la poubelle. Ce n'était visiblement pas une bonne série...
My 251 still did not boot after the 100ohm resistor hack. Actually, it booted once and beeped but then after powering off, it went back to the blue and red LEDs as before. I think mine needs more resistance even though after the 100ohm resistor was added, the voltage across pins 1 and 8 is the required 1.47V approx. and the voltage between 1 and 6 is 3.3V.
The 100 ohm resistor fix that I present in this video is not always 100% successful: based on the reports that I have received, it works in > 95% of the cases, but sometimes the problem is not solved. When the problem is not solved, in most cases it is because the other junction of the faulty part is also faulty... (the 100 ohm resistor makes the clock voltage back to the normal value, but does obviously nothing on the other junction). I don't know what is the normal voltage between pins 1 and 6: 3.3V looks like a common Power Supply voltage figure, but I don't know what the pins 1 & 6 are connected to. If your device has the other junction faulty, I know no fix: I had followed different threads on the specialized forums at the time I made this video, but I found no solution at this period. It will be difficult to identifya solution: it is beyond my current knowledge, sorry...
Hil Elodie, would you be willing to make some resistors and sell them for cost/effort? - would be interested to buy one (delivery can either be France/UK for me)
Hi, I currently do not have enough time to build them, because I have too many projects (and much more complex ones) in progress. But if you need one for your own NAS, just drop me an email and I will send one to you. Delivery will be in France because UK is no longer in the E.U. and dealing with the Customs will just be a nightmare...
Good evening everyone. Not being an electrical engineer can someone link a resistor model that can be purchased on amazon? I have seen that they exist with various WATTS values. Thank you.
Hi Nicola, Sorry for my late reply but I was not at home... There are plenty of choices on Amazon, eBay or others, but you will have to pay an additional cost by buying just one... You just have to perform a search using the following Keywords: Resistor, Metal Film, 200 ohm, 1/2W. In my video I have soldered a 100 ohm resistor but, it is wise to use a higher value such as 200 ohms for example. Regarding the Wattage of the resistor, 1/2Watt (0.5W) is fine : higher wattage may have thicker pins that could not be put into de holes. For example: www.amazon.fr/sourcing-map-R%C3%A9sistance-m%C3%A9tallique-100Pcs/dp/B07M7NNT5P If you need to order from a specific country, just tell me and I will perform the search for you. If you live in Europe, I can give you a resistor at no cost: you will just pay the shipping cost ! just tell me.... Nounours
Hello, I apologize but my website has been totally hacked (2 times) and is out of order ! You can download the diagram directly from my cloud here: mega.nz/file/Quh2xZRb#p4cLG2MuAzYr05nSffNhLuQ8dxVRssUMTrVyyXIRZOY
Yes: if your NAS does not have the headers installed, you can solder the resistor directly on the Motherboard, or solder an header and install the resistor as described in the video. Most of the Synology don't have the headers installed. I hope this video has helped you !
Where do I do this on the TS-453 Pro. Mine is Stuck on the Boot with No HDMI output, Beep. last email log says fan 1 fail but fan seems to be working. Thanks
@@ratul2k7 The mobo shown in this video is virtually identical to the TS-453 Pro. The only difference on mine from what is shown here was that the pins where the resistor is attached didn't have actual *pins* - but the place on the mobo is the same. Just locate it by the adjacent fan connectors.
I am happy for you: one more NAS back to life ! Do not forget to backup your data, because it is a temporary fix: your NAS can work for a few weeks to a few years, nobody knows. Mine has worked for 2 years after this fix and was still running perfectly when I sold it. But some others have only work for a few weeks...
Bonjour, merci pour votre vidéo déjà. Je viens de faire la manipulation et ça à l'air de fonctionner. Qnap me propose une réparation à 200$. Il m'ont même répondu qu'il connaissait cette manipulation, mais que cela ne durera pas dans le temps qu'en pensez-vous ? Merci encore.
Je n'avais pas vu votre question, désolé. En effet cette réparation est provisoire car le pb vient d'un circuit intégré mal conçu: tôt ou tard la "mort" sera définitive. Mais QNAP doit expliquer quelle réparation ils font: car à moins de changer le circuit intégré défectueux, je ne vois pas de solution long terme. QNAP connaît bien sûr cette manipulation, elle a même été appliquée par QNAP eux-mêmes à certains clients tombés en panne sous garantie (c'est que certains affirment, personnellement je n'ai jamais renvoyé mon NAS à QNAP, vu qu'il n'était plus sous garantie). Et d'après ce que certains disent, QNAP comme d'autres, ont continué à vendre des produits alors qu'ils avaient connaissance de ce défaut... Bref, beaucoup voudraient savoir quelle est la réparation proposée par QNAP !??!
Très heureux que votre NAS ait ressuscité comme tant d'autres ! J'ai réparé le mien il y a plus d'un an maintenant, et il fonctionne toujours à merveille, en étant allumé 24h/24; pourtant il a une résistance de 100 ohms, que j'aurais pu augmenter pour préserver davantage les composants... Donc il mourra surement un jour, mais jusqu'à présent, c'est le pied ! On ne peut pas dire que QNAP ni SYNOLOGY aient fait beaucoup d'effort pour "dépanner" leurs clients: ils auraient au oins pu donner le remède, quitte à dire qu'il n'y avait pas de garantie....
@@HOME2VER Je sais qu'il existe une vidéo en anglais de quelqu'un ayant réalisé ce changement de processeur, mais je ne la retrouve plus ! C'est quelqu'un qui a eu le même problème que nous (no boot) pour la même raison (horloge HS) et qui a mis en place la même solution, à savoir rajouter une résistance de pull-up. Mais comme il avait extrait la carte mère car il ne connaissait pas la solution de la résistance de 100 ohms (ou plus), il en a profité pour changer le processeur. C'est sur un QNAP aussi, la vidéo était en anglais. Pour ma part je ne tenterai pas l'opération pour plusieurs raisons: 1-d'autres parties que l'horloge des QNAP peuvent défaillir avec le temps: certains ont déjà eu des problèmes avec les connexions réseau LAN qui ne se faisaient plus de temps à autre. Donc disons qu'à partir d'un certain âge, il ne faut pas non plus faire de
@@elodiecemoi3057 bien évidement je ne peut être que d'accord avec vous , c'est vrai que pour le coup nous avons eu également très peur de perdre 11 ans de video avec les enfants , vacances , mariage etc.. . Je vous suis entièrement redevable , encore merci d'avoir eu le courage de faire votre video . Bonne continuation . Cordialement Jérôme
@@HOME2VER Si vous avez (comme moi) autant de souvenirs sur votre NAS, investissez dans un NAS de sauvegarde, vous dormirez plus tranduile ! Car celui-ci, bien que réparé, peut retomber en panne demain... Désormais mon NAS réparé me sert de sauvegarde (je l'ai passé de Raid-6 avant à Raid-5 désormais) et j'ai acheté un autre NAS (configuré en Raid-6) qui est devenu mon NAS principal. Les souvenirs de nos enfants, de notre mariage (et dans mon cas, de ma naissance !) valent bien un petit investissement pour les protéger... Bonne continuation !
Does anyone have any spare parts they might be willing to post to me (UK)? I'll pay by Revolut. Seems ridiculous to buy 40 x NSR connectors and 40 x resistors...I only need one of each!
I am OK to give you 2 NSR connectors and the resistor (do you have the appropriate crimp tool ??): I am not sure that the postage will save you money... I have no Revolut account and not going to open one, only Paypal) --> Drop me an email to threshold-loversATgmx.fr
There is a very little current (Ampere) flowing through such a resistor: 1/4 W is enough, but you can use a higher wattage, it's not dangerous (just a bigger resistor).
Bonjour, j'ai trouver ta video sur youtube alors j'ai un probleme avec un qnap ts453 pro qu'il est bloquer sur booting system? ta pas une solution pour sa merci :)
Bonjour, Malheureusement si après avoir soudé la résistance comme indiqué dans cette vidéo tu as toujours le problème, c'est probablement que tu as les DEUX jonctions qui sont mortes, et je n'ai pas trouvé de solution dans ce cas.... Peut-être y en a-t-il une sur le Web, mais je n'en ai pas trouvé... Sorry !
I have just hit the link 5 seconds ago, and it does work without any problem: you should have a probelm... Please try again, and if you cannot download the diagram, drop me an email (threshold-loversATgmx.fr) and I wll send it to you.
Any resistor with a value between 100 ohm and 350 ohm, wattage = 0.25 Watt to 0.5 Watt, preferably a "metal film" resistor but any kind of material will be OK. Feel free to ask if you have any question,
Merci pour ce tuto. Mon 853 est complètement inopérant. Aucun bip, même sans la Ram et HDD. Reset ne fonctionne pas. Je compte tenter ta méthode. Malheureusement je n'ai que des résistances de 150ohm sous la main :/
C'est encore mieux: tout le monde s'accorde à dire qu'en mettant une résistance plus élevée vous prolongerez davantage la durée de vie de votre NAS (parce qu'avec une R plus élevée, le courant traversant le composant défectueux sera plus faible et donc il devrait durer plus longtemps avant de mourir). On s'accorde que vous pouvez aller jusqu'à 350 / 400 ohms, donc si vous avez une 150 ohms sous la main, allez-y.
@@elodiecemoi3057 merci pour ta réponse. Je l'ai soudée ce matin et comme par magie il a ressuscité d'entre les morts. Incroyable !. Apparemment j'ai vu qu'une autre pin permettait de résoudre un autre problème. Moi qui est plutôt pro Synology,ca me conforte dans mon idée ;) Encore merci 👍🏻
@@stivxbox Heureux pour toi ! je crois qu'on ne peut plus compter le nombre de personnes ayant sauvé leur NAS avec cette méthode (dont je fais partie !), A bientôt sur Threshold-Lovers.com
Sorry for that ! we have faced problems with th Download Manager (and we still have problems): I have change the permissions required, so you should be able to download the diagram from now. If not, drop me an email: threshold-loversATgmx.fr andi will send it to you. Good luck with your NAS...
@@mameawchannel5870 if your NAS boots but does not pass Bios, it is maybe not only a clock issue (that you have probably fixed with the 100 ohms resistor solution) but it could be a problem with the internal battery that feeds the motherboard. It is not sure at all, bit I would try to replace the Lithium battery (it has a "button" form factor): sometimes it brings your NAS back to life for 2$ !!
I have tried to download it just now, and it works: try with another browser (with Chrome, no problem to download it), or send me your email (use the email in the "contact us" menu on the threshold-lovers.com website) and I will send the diagram to you.
100 Ohm doenst work 65 Ohm FIX the Problem !!! But with 65 Ohm the System need 5-10 Min to Boot (Display shows all the time "BOOTING") but i can move the Data to the new NAS
The lower the resistor value, the higher the current is in the faulty transistor ! So I strongly suggest to backup your data as soon as possible ! For the other readers, I remind that this solution does not definitely fix the problem : the NAS may (will ?) die in a few days, few weeks or few months... nobody knows. Mine a run perfectly during 18 months after the 1st problem: but at least this solution allow you to get access to your data. Remember: a NAS is not a backup !
Great ! am happy to count you amongst the thousands of rescued people ! But do not forget that there cannot exist any permanent fix for this problem, due to a design fault with the processor. Consequently, sooner or later, your NAS will die: be careful to backup your data, and... think about a replacement unit in the future ! To give you an idea, mine has worked again during 2 years before dying forever, but some persons have reported a couple of months only...
D'après ce que j'ai pu lire (en diagonale) sur un forum le souci de boot est du à un bug dans le silicium du processeur J1900. Le problème viendrait d'une sortie du bus LPC (low pin count), un bus de discussion avec des périphériques lents comme capteurs de température, EEPROM etc... Lors du démarrage du systèmes le Firmware dois vérifier des données transitant sur ce bus et l'échec de la communication intérromp la procédure de boot. Pour les plus curieux, qui voudraient approfondir, le problème viendrait d'un transistor mosfet sur une sortie du bus LPC. Cette sortie a 2 transistors qui fonctionnent à tour de rôle pour "tirer" la sortie soit vers le 1 ou le 0 et un des 2 transistors faiblit avec le temps ce qui force cette sortie dans un état illégal entre 0 et 1. La résistance ajoutée en parallèle avec le transistor défectueux vient partiellement rétablir le fonctionnement du bus LPC en permettant à l'autre transistor de fonctionner. Les niveaux logiques ne sont pas aussi propres qu'à l'origine mais suffisamment clairs pour permettre le fonctionnement, au moins pour un temps. Ceci n'est PAS un problème QNAP c"est un bug Intel (je n'ai pas la source en tête). Malheureusement il y a batch des processeurs Atom J1900 qui ont ce bug silicium de vieillissement prématuré des transistors du bus LPC. Je ne suis pas sûr qu'il y ait une solution définitive comme l'ajout d'un buffer pour que a sortie en question travaille avec un très fable courant par exemple.
Entièrement d'acord: tu as parfaitement décrit le problème ! Je n'ai pas non plus trouvé de solution définitive, le remède que je présente dans cette vidéo étant avant tout destiné à ne pas perdre se données et à pouvoir les migrer tranquillement... Les autres NAS avec le même processeur (Synology et autres) ont bien sûr connu la même panne.
@@elodiecemoi3057 Après avoir fait la "réparation de fortune" avec la résistance il y a apparemment une fonction logicielle surnommée "LPC_CLKRUN#" qui permet de mettre le bus LPC en veille ce qui économiserait le vieillissement et rallongerait la durée de vie. Donc mise à jour du firmware. Après quelques recherches il s'avère que le problème se manifeste sur plusieurs séries de CPU: J1900 AVR54 E3800 VLI89 VLI90 Chez Intel les CPUs ont des codes de batch le "stepping" par exemple 'C0'. Il me semble que le soucis a été réglé à partir de certains stepping et que c'est pour ça que la production de toutes les puces faible TDP a été interrompue. Je n'ai malheureusement pas trouvé plus de détails. Sinon il y a toujours la possibilité de carrément utiliser une carte mère Mini ITX standard. la connection ver le backplane des disques durs est normalement du PCI express standard. Il faut vérifier le nombre de "Lanes" PCI express nécessaires ça change suivant les modèles (1x, 2x ou peut-être même 4x). Là il va falloir jouer avec la scie pour adapter le panneau arrière. Liens des sources: en.wikipedia.org/wiki/Silvermont#Erratum superuser.com/questions/1762455/did-the-intel-j1900-flaw-get-fixed wiki.jmehan.com/pages/viewpage.action?pageId=44695614 www.congatec.com/fileadmin/user_upload/Documents/Technical_Documents/BYT_xA30_Errata_LPC_USB_SD_Card.pdf En particulier la section "Reason for the Failure" qui donne la liste des CPUs et Familles affectées
Bonjour, Même si la solution indiquée fonctionne dans 95% des cas, il y a des cas où cela ne fonctionne pas car il peut exister 2 causes (la plus fréquente se résoud par l'installation de la résistance comme indiquée, l'autre n'a malheureusement pas de solution à ma connaissance). Si votre TS-251 ne démarre toujours pas, il est plus que probable que vous soyez dans ce 2ème cas... et le remplacement pur et simple me semble la seule approche possible, navré pour vous... Bien cordialement,
Vous pouvez essayer de diminuer un peu la valeur de la résistance, disons à 65 ohms (plus la valeur est faible plus le signal d'horloge est élevé): cela peut parfois résoudre le problème comme l'indique une personne plus bas...
@@elodiecemoi3057 en baissant la résistance à 55 ohms, j'ai réussi à faire démarrer le NAS ! Merci. Mais c'est juste un signe que la carte mère est encore plus au bord d'être définitivement HS...
@@vincentpaire5993 Oui ça ne sent pas très bon ... ça a permis de redémarrer et donc de sauver tes données, c'est déjà énorme, mais soit prudent: backup immédiat, et régulier si ce n'est pas déjà automatisé...
This fix brought my QNAP TS-451+ back to life! Thank you for saving me hundreds of dollars by sharing this valuable information. Much appreciated.
You are welcome: I did face the same problem than you, with the same level of stress, so I was sure this wideo and diagram will help a lot of people ...
Enjoy !
I already was looking for a replacement of my QNAP TS-851 when I saw this fix. I thought the MB was dead but the described symptoms matched mine exactly. So thanks for a solution that cost me about 5 cents. Many thanks to you....
Yes ! Another QNAP saved ! I cannot count how many NAS this video has already saved !...
Thanks so much for posting this way back in 2021!
I have brought my 6-yo+ NAS back to life with a 100ohm resistor and some very amateur soldering. Really appreciate you posting this so we could all work through it.
My pleasure: the number of persons that have save their NAS with this solution, is countless !
Do not forget that this should not be taken has a permanent fix: there is a deep problem with these CPUs and, sooner or later, the NAS will die forever !
Save your data in another place if you continue to use it...
Thank you!! Had a hard time tracking down a 100 ohm resistor locally but eventually found one. Attached it to pin 1 and 8 and it booted right up. Amazing!! You bought me some time to replace this heap of crap. Cheers!
Good news ! that is the purpose of this fix !
My NAS has been fixed for months and it is still running perfectly ! nobody knows how long a NAS will continue to run after this fix, but based on what I have read, it is many months...
Thank you Rob : I am very happy to see that you get out of the trouble ! One more NAS saved...
Yes it is amazing because there are a lot of persons havind this problem, and since I have made this video, thousands of peopla have fixed their boot problem using this method !
Have a nice Christmas !
MERCI BEAUCOUP, j'ai réussi à réparer mon TS-251 grâce à ta vidéo !
Excellente nouvelle ! je suis heureux pour toi et pour toutes les personnes qui ont pu se dépanner grâce à cette vidéo !
It worked like a charm for a QNAP TS-853+ Pro. Thank you very much!
You are welcome: one more NAS saved !!
I have been told that you can increase the resistor value up to 430 ohms, with the benefit to reduce the current (Amps) flowing through the faulty part, and therefore increasing the life time of the repaired device.
Bur I have not yet tested !
Thanks so much for this video. I was able to save a ton of files after my QNAP died a few days ago!
Good news !
J’avais ça: Status = OFF, USB = BLUE, LAN = clignote / sur un TS 651.
Merci à toi pour ce partage! Tu viens de me faire économiser une somme. Avec de la gaine thermique c’est très propre. Et surtout le NAS fonctionne parfaitement. Je sauvegarde tout et me fait une routine de sauvegarde sur d’autres disques avant que mon NAS soit plus bas que terre.
Très heureux pour toi ! Un nas de plus sauvé de la poubelle 👍👍
Merci pour cette petite astuce, j'ai pu ramener un TS-653PRO à la vie avec ça !
Heureux pour vous, un NAS de plus sauvé de la benne ! jene les compte plus !
N'oubliez pas de faire un backup complet de vos données, car cette solution ne vous met pas à l'abri d'une panne définitive (le défaut du processeur existant toujours)....
Thank you!! It worked perfectly on a ts-853 pro with the 100 ohm resistor
I am happy for you ! one more user and NAS saved ! Do not forget that it is supposed to be a temporarily fix only: the NAS is supposed to die in the future... Mine has been working for months and is still OK... But do not forget to backyp your data !
This really saved me and my family's NAS qnap ts-253 pro. Back up and running!
I am happy that my video has helped you : one more NAS saved !....
Mine has been saved by doing this and it has heen running back like a charm for more than 1 year...
@grey I'm just experiencing this issue with ts-253 pro, can you confirm if you have used 100 Ohm and it helped?
@@czaras_ yes it definitely worked in our QNAP and has been up ever since I posted that
Danke!
Super Tipp!
Läuft wieder. 👍
One more NAS saved ! I am happy for you 👍👌😎
Thank you for this, and more importantly, the pin diagram!! Will try this once the parts turn up
Keep us posted: in 99% of the case, this fix solves the problem !
I had found a few explanations on the problem on the Web but I had not found the diagram: so I was sure that this diagram would be helpful !!
@@elodiecemoi3057 Worked perfectly. I had to solder direct onto the MB which was slightly scary, but booted up first time
Good news ! One more NAS saved 😉
Saved my TS-853U thank you!
Superb ! I have implemented this fix more than a year ago, and my NAS has been working like a charm !
Thanks i have a TS 451 . I tried a 120 ohm resistor on pin 1 and 8 did not work. I used a 100 ohms . Works perfectly . I was able to recovered almost 25 gb from it . Thanks to everyone
I am happy for you! One more NAS fixed !
Can it be normal that both measurements of pin 1-8 and pin 1-6 are equally low? I am measuring on both Pin 1-6 and 1-8 around -0,05V. This seems to indicate per your diagram that I need a resistor of 100 Ohm between pin 1 and 6, as it is
Thank you! It works! (TS-453 Pro).
Super : one more NAS saved by this solution !!! I am very happy to help you guys 👍👍
What size crimp are you using? I see it's a 28-20 AWG. From what I understand the female connector is 2.54mm does that matter? Or is the smaller crimp sizes just to be able to crimp the pin to the resistor legs?
You are wrong on several aspects:
-the "2.54mm" value that you mention, is the distance between 2 male pins. This 2.54mm is a standard value for the Printed Circuit Boards hole distance, in which the male pins are soldered. These male pins can be the Dupont male pins (like the ones I show in the video) or another standardized category, such as the KF2510 male connectors that also fit in the PCB holes having the usual 2.54mm spacement.
-The crimp size is written on a crimp tool, and relates to the diameter of the cable that will be crimped into the female connector: it does not relates to the distance between 2 PCB holes. When I crimp a cable (or a resistor) in a Dupont female connector, I use the 1.3mm position on my crimp tool.
Hope this helps !
God Bless you!
Another TS-251+ saved in Malta🥳
Yessss !
I am very happy for you !
Mine died definitely last week, but it has been running approximately 2 years more with this fix !
Do not forget that a NAS always need a backup, and sooner or later, your NAS (with this fix) will definitely die...
Enjoy !
@@elodiecemoi3057 maybe is time to sell it 😁
@@AlexNoise Yes, it is for sale since yesterday (!), as a spare parts unit !
I do not need it anymore since I have bought another 8-bays NAS as my main NAS, and since I have re-organized all my backup plan to another 4-bays NAS that should be convenient for the backups ...
Thanks for posting this! I'm in the process of getting data off my drives...to transfer to a Synology NAS 🙂
Good luck ! Tell us if you have succeeded ??
@@elodiecemoi3057 Data retrieved 🎉!!! New Synology on order, probably going to do a more permanent solder job and then sell it for peanuts on ebay. Do you have a tip jar?
@@EdGriebel Sorry for my unperfect Englis: what do you mean by "tip jar" ??? I have ordered a Synology too (an 8 bays DS1821+), not because they are better than the QNAPs (both QNAP and Syno have had this issue, as every other manufacturer using this faulty serie of Intel processors) but because thay have the SHR-2/BTRFS technology that allow to mix more easily the disks with different capacities.
Feel free to ask if you have another question
DANKE!! Auch mein NAS läuft wieder!
You are welcome : I am happy to see that my video has saved the NAS of so many persons !!😇 Mine died last week, this time both all the dsks got the red status LED...
I believe that this serie was not the best of QNAP
Sooo gratefull!!! It helped!
One more NAS saved ! I am happy for you ! Enjoy !
this worked on my Qnap TS 251+ with the 100ohm resistor on the 1 and 8 pin
One more NAS saved ! I am happy for you !!👍👍
Hi, is this the workaround fix for the Intel Apollo Lake CPU dying issue? I just got my hands on a used TS453be without reading on the CPU issues in advance, so if it is this easy to fix it I might keep it.
I believe it is, but remember that this fix is not a permanent fix: the CPU will die sooner or later (this is 100% sure) because of their faulty design.
Mine has been operational 2 years after this fix, but finally died.
Hi, I also have a problem with a model nose: qnap TS-415 white. After the LEDs on the hard drive were all red and the LED on the system was off.
The first time the fan started, but I couldn't find it on the network, after several searches I noticed that it was a problem on the motherboard.
I searched the internet and found that I had to unplug it, connect a 100 ohm transistor or resistor between two pins, I did that, I connected the 100 ohm resistor between pin 1 and 8.
After I restarted the NAS, only the problem from the LED u from the hard drive disappeared, that is, it was seen in green only at slot 1 on the hard drive where I had one placed but still the status LED is off and not booting. What else can I do for them?
I just see your question now, so sorry for the delay.
The 100 ohm (or preferabily more for long term reliability) is a fix that works in 99% of the cases, by setting the clock voltage back to an acceptable value (soo the clock signal is back).
But in some cases, the 2 junctions of the (internal) transistor are both faulty, and in that case the 100 resistor can't fix the problem.
I am not aware of any solution in that case, maybe you can search on the web, but I know that there are similar issues that can't be solved....
@@elodiecemoi3057 Unfortunatly, same Led result here with TS-453 Pro
The voltage between pin 1 and 8 was -2.435V so I bought a 100Ohm Resistor (1/4 W) like it was explained.
With the 100ohm resistor, the voltage is -1.523V but it seems we have to obtain -1.7V so probably I have to use another value of resistor but I don't know which value I have to buy.
Could you help me or tell me if it's a good idea to persist ?
Thank For This!!! It Work For Me. (TS-453 Pro)
One more NAS saved !
I don't know how to proceed, but I would be veru interested to know how many NASes have been saved by this solution !!
If somebody know how to do...
Enjoy !!
I have a TS 453-Pro stuck on "SYSTEM BOOTING". Can I utilize this method? Do you have a connector diagram for my NAS. Thanks a lot.
Hello,
Sorry but my website has been totally hacked and is out of order !
You can download the diagram directly from my coud here:
mega.nz/file/Quh2xZRb#p4cLG2MuAzYr05nSffNhLuQ8dxVRssUMTrVyyXIRZOY
Good lick
Merci beaucoup ! cette astuce a ressuscité mon TS-853 PRO !
Petite précision sur mon modèle, il n'y a pas de connecteur et j'ai été obligé de souder directement
Thank you so much ! this trick has revived my TS-853 PRO!
Small clarification on my model, there is no connector and I had to solder directly on it
Good news again : one more NAS saved ! The presence of a connector depends on the model: some models have it, some other don't..
@@elodiecemoi3057 Pareil, Pas de connecteur, directement soudé sur la carte mère de mon TS-453 Pro mais pour moi, pas de résultat probant :(
Avant soudage de la résistance de 100Ohm (1/4W), la tension était de -2.435V et après de -1.523V alors qu'on devrait semble t il obtenir -1.7v.
Peut être qu'avec une autre valeur de résistance ça pourrait fonctionner mais je ne sais pas calculer la valeur nécessaire malheureusement :(
Après différents tests avec des résistance de valeur différentes, j'ai réussi à obtenir la valeur de 1.706v avec une résistance de 140ohm 1/4w mais malheureusement ça ne fonctionne pas la led status reste éteinte, la led usb est bleu, la led du 1er disque dur est verte et les autres disques dur rouge, pas de bip,..
I did some other tests with differents values of resistor and at the end, with a resistor of 140ohm 1/4w, i can obtain -1.706v
But same result, it doesn't to boot, no bip... only usb leb in blue, green led of the 1st HDD and the others HDD are Red...
Sad :(
Super utile merci de partager ce genre de tutoriel !
J'ai un TS-251+ qui n'a pas encore (!) lâché. Juste pour comprendre à 100% le jour où cela arrivera et si la réparation par la résistance 100 Ohm échoue je pourrai quand même récupérer mes données en utilisant un autre NAS QNAP en insérant "simplement" mes disques durs dans un autre NAS ? Ou pas :( :( ??
C'est possible mais pas tous les NAS pourront récupérer les disques de votre TS-251+ : sur le site de QNAP l'info s'y trouve peut-être, mais le mieux est de contacter le Support QNAP en leur disant que "vous n'êtes pas satisfait du tout, que vous voulez un modèle capable de relire les disques de votre TS-251, et que s'ils ne vous proposent pas une remise vous passez chez Synology".
La plupart du temps ils vous proposent 20% sur un nouveau NAS capable de relire vos disques.
Rassurez-vous, ceux qui ont des problèmes avec Synology font la même chose en sens inverse !
Personnellement, j'ai à la fois du QNAP et du Synology...
I'm hoping this will work on my 653B. It's been sitting in a box after it gave the red light of doom and I invested the $350 QNAP wanted into a TVS-672N instead. I have a use for the 653B again and hopefully this will work. I'll report back!
Hi Devin,
How is your 653B after you tried this fix ? is it back to life ?
Cela a fonctionné avec un TS-851, 110 ohm, pin 1-8.
Merci infiniment!
Heureux pour vous !
Avec plus de 37.000 vues, je ne compte plus le nombre d'utilisateurs en détresse ainsi sauvés, et de NAS qui sont revenus à la vie !
Je ne pensais pas que ma solution serait aussi utile 👍👍
hello everybody I have a ts-451 i tried that fix using a resistor 120ohm 2w but i did not work. could anyone tell me exactly what resistor i will need to buy? please
It says in the description you need to use a 100OHM resistance. Maybe try such a resistance again :)
Bonjour, Faut retirer la resistance une fois nas rebooté ? ton nas reparé marche toujours ?
Non: la résistance doit rester en place, puisque c'est elle qui permet de générer à nouveau une fréquence d'horloge correcte.
Mon NAS ainsi réparé a fonctionné parfaitement pendant 2 ans, mais maintenant c'est sa carte réseau qui est morte...donc il va finir à la poubelle. Ce n'était visiblement pas une bonne série...
My 251 still did not boot after the 100ohm resistor hack. Actually, it booted once and beeped but then after powering off, it went back to the blue and red LEDs as before. I think mine needs more resistance even though after the 100ohm resistor was added, the voltage across pins 1 and 8 is the required 1.47V approx. and the voltage between 1 and 6 is 3.3V.
The 100 ohm resistor fix that I present in this video is not always 100% successful: based on the reports that I have received, it works in > 95% of the cases, but sometimes the problem is not solved.
When the problem is not solved, in most cases it is because the other junction of the faulty part is also faulty... (the 100 ohm resistor makes the clock voltage back to the normal value, but does obviously nothing on the other junction).
I don't know what is the normal voltage between pins 1 and 6: 3.3V looks like a common Power Supply voltage figure, but I don't know what the pins 1 & 6 are connected to.
If your device has the other junction faulty, I know no fix: I had followed different threads on the specialized forums at the time I made this video, but I found no solution at this period.
It will be difficult to identifya solution: it is beyond my current knowledge, sorry...
Not 1 and 9?
Hil Elodie, would you be willing to make some resistors and sell them for cost/effort? - would be interested to buy one (delivery can either be France/UK for me)
Hi, I currently do not have enough time to build them, because I have too many projects (and much more complex ones) in progress.
But if you need one for your own NAS, just drop me an email and I will send one to you.
Delivery will be in France because UK is no longer in the E.U. and dealing with the Customs will just be a nightmare...
@@elodiecemoi3057 sure. Thank for helping out. Where to find your email address?
@@elodiecemoi3057 found the email address and sent you an email on the 27th
@@Montagne76 I have posted you the resistors, but no news since then...
@@marcwall481 go to my Website: www.threshold-lovers.com and then go to the "contact us" section...
Good evening everyone. Not being an electrical engineer can someone link a resistor model that can be purchased on amazon? I have seen that they exist with various WATTS values. Thank you.
Hi Nicola,
Sorry for my late reply but I was not at home...
There are plenty of choices on Amazon, eBay or others, but you will have to pay an additional cost by buying just one...
You just have to perform a search using the following Keywords: Resistor, Metal Film, 200 ohm, 1/2W.
In my video I have soldered a 100 ohm resistor but, it is wise to use a higher value such as 200 ohms for example.
Regarding the Wattage of the resistor, 1/2Watt (0.5W) is fine : higher wattage may have thicker pins that could not be put into de holes.
For example: www.amazon.fr/sourcing-map-R%C3%A9sistance-m%C3%A9tallique-100Pcs/dp/B07M7NNT5P
If you need to order from a specific country, just tell me and I will perform the search for you.
If you live in Europe, I can give you a resistor at no cost: you will just pay the shipping cost ! just tell me....
Nounours
i just typed in 100 ohm and got a pack of 10 for £3.69
Merci pour cette video, sais tu où trouver les conecteurs NSR femelle à sertir stp?
Oui: chez Gotronic.fr il y en a à beaucoup d'endroits, mais ceux de Gotronic sont de bien meilleure qualité !
Hello, thanks for you sharing. It is possible share diagram the link dont work . Can i use this method to ts-653 pro. Thanks
Hello,
I apologize but my website has been totally hacked (2 times) and is out of order !
You can download the diagram directly from my cloud here: mega.nz/file/Quh2xZRb#p4cLG2MuAzYr05nSffNhLuQ8dxVRssUMTrVyyXIRZOY
thanks @@elodiecemoi3057
This worked for me. TS-453 Pro. Mine did not have headers installed - so I soldered directly to the mobo.
Yes: if your NAS does not have the headers installed, you can solder the resistor directly on the Motherboard, or solder an header and install the resistor as described in the video.
Most of the Synology don't have the headers installed.
I hope this video has helped you !
Where do I do this on the TS-453 Pro. Mine is Stuck on the Boot with No HDMI output, Beep. last email log says fan 1 fail but fan seems to be working. Thanks
@@ratul2k7 The mobo shown in this video is virtually identical to the TS-453 Pro. The only difference on mine from what is shown here was that the pins where the resistor is attached didn't have actual *pins* - but the place on the mobo is the same. Just locate it by the adjacent fan connectors.
It works!!!! Thank you!!
I am happy for you: one more NAS back to life !
Do not forget to backup your data, because it is a temporary fix: your NAS can work for a few weeks to a few years, nobody knows.
Mine has worked for 2 years after this fix and was still running perfectly when I sold it. But some others have only work for a few weeks...
@@elodiecemoi3057 OK. Tanks. I will keep in mind
Bonjour, merci pour votre vidéo déjà. Je viens de faire la manipulation et ça à l'air de fonctionner. Qnap me propose une réparation à 200$. Il m'ont même répondu qu'il connaissait cette manipulation, mais que cela ne durera pas dans le temps qu'en pensez-vous ?
Merci encore.
Je n'avais pas vu votre question, désolé.
En effet cette réparation est provisoire car le pb vient d'un circuit intégré mal conçu: tôt ou tard la "mort" sera définitive.
Mais QNAP doit expliquer quelle réparation ils font: car à moins de changer le circuit intégré défectueux, je ne vois pas de solution long terme.
QNAP connaît bien sûr cette manipulation, elle a même été appliquée par QNAP eux-mêmes à certains clients tombés en panne sous garantie (c'est que certains affirment, personnellement je n'ai jamais renvoyé mon NAS à QNAP, vu qu'il n'était plus sous garantie). Et d'après ce que certains disent, QNAP comme d'autres, ont continué à vendre des produits alors qu'ils avaient connaissance de ce défaut...
Bref, beaucoup voudraient savoir quelle est la réparation proposée par QNAP !??!
Merci j'ai réussi à faire revivre un TS25+ donné comme HS par QNAP . Avec un peut plus de recul combien de temps votre NAS a t'il réussi à tenir ?
Très heureux que votre NAS ait ressuscité comme tant d'autres !
J'ai réparé le mien il y a plus d'un an maintenant, et il fonctionne toujours à merveille, en étant allumé 24h/24; pourtant il a une résistance de 100 ohms, que j'aurais pu augmenter pour préserver davantage les composants...
Donc il mourra surement un jour, mais jusqu'à présent, c'est le pied !
On ne peut pas dire que QNAP ni SYNOLOGY aient fait beaucoup d'effort pour "dépanner" leurs clients: ils auraient au oins pu donner le remède, quitte à dire qu'il n'y avait pas de garantie....
@@elodiecemoi3057 Génial et merci pour votre réponse . Pensez vous qu'un changement de processeur est envisageable ?
@@HOME2VER Je sais qu'il existe une vidéo en anglais de quelqu'un ayant réalisé ce changement de processeur, mais je ne la retrouve plus !
C'est quelqu'un qui a eu le même problème que nous (no boot) pour la même raison (horloge HS) et qui a mis en place la même solution, à savoir rajouter une résistance de pull-up.
Mais comme il avait extrait la carte mère car il ne connaissait pas la solution de la résistance de 100 ohms (ou plus), il en a profité pour changer le processeur.
C'est sur un QNAP aussi, la vidéo était en anglais.
Pour ma part je ne tenterai pas l'opération pour plusieurs raisons:
1-d'autres parties que l'horloge des QNAP peuvent défaillir avec le temps: certains ont déjà eu des problèmes avec les connexions réseau LAN qui ne se faisaient plus de temps à autre. Donc disons qu'à partir d'un certain âge, il ne faut pas non plus faire de
@@elodiecemoi3057 bien évidement je ne peut être que d'accord avec vous , c'est vrai que pour le coup nous avons eu également très peur de perdre 11 ans de video avec les enfants , vacances , mariage etc.. . Je vous suis entièrement redevable , encore merci d'avoir eu le courage de faire votre video . Bonne continuation . Cordialement Jérôme
@@HOME2VER Si vous avez (comme moi) autant de souvenirs sur votre NAS, investissez dans un NAS de sauvegarde, vous dormirez plus tranduile !
Car celui-ci, bien que réparé, peut retomber en panne demain...
Désormais mon NAS réparé me sert de sauvegarde (je l'ai passé de Raid-6 avant à Raid-5 désormais) et j'ai acheté un autre NAS (configuré en Raid-6) qui est devenu mon NAS principal.
Les souvenirs de nos enfants, de notre mariage (et dans mon cas, de ma naissance !) valent bien un petit investissement pour les protéger...
Bonne continuation !
Does anyone have any spare parts they might be willing to post to me (UK)? I'll pay by Revolut. Seems ridiculous to buy 40 x NSR connectors and 40 x resistors...I only need one of each!
I am OK to give you 2 NSR connectors and the resistor (do you have the appropriate crimp tool ??): I am not sure that the postage will save you money... I have no Revolut account and not going to open one, only Paypal) --> Drop me an email to threshold-loversATgmx.fr
what is resistor 100r 1/4w or 1w?
There is a very little current (Ampere) flowing through such a resistor: 1/4 W is enough, but you can use a higher wattage, it's not dangerous (just a bigger resistor).
Bonjour, j'ai trouver ta video sur youtube alors j'ai un probleme avec un qnap ts453 pro qu'il est bloquer sur booting system? ta pas une solution pour sa merci :)
Bonjour, Malheureusement si après avoir soudé la résistance comme indiqué dans cette vidéo tu as toujours le problème, c'est probablement que tu as les DEUX jonctions qui sont mortes, et je n'ai pas trouvé de solution dans ce cas.... Peut-être y en a-t-il une sur le Web, mais je n'en ai pas trouvé... Sorry !
Peut être la DOM qui est dead ?
hi, the link for the diagram is no longer working.
I have just hit the link 5 seconds ago, and it does work without any problem: you should have a probelm... Please try again, and if you cannot download the diagram, drop me an email (threshold-loversATgmx.fr) and I wll send it to you.
Anyone know the exact resistor specification?
Any resistor with a value between 100 ohm and 350 ohm, wattage = 0.25 Watt to 0.5 Watt, preferably a "metal film" resistor but any kind of material will be OK. Feel free to ask if you have any question,
Merci pour ce tuto. Mon 853 est complètement inopérant. Aucun bip, même sans la Ram et HDD. Reset ne fonctionne pas. Je compte tenter ta méthode. Malheureusement je n'ai que des résistances de 150ohm sous la main :/
C'est encore mieux: tout le monde s'accorde à dire qu'en mettant une résistance plus élevée vous prolongerez davantage la durée de vie de votre NAS (parce qu'avec une R plus élevée, le courant traversant le composant défectueux sera plus faible et donc il devrait durer plus longtemps avant de mourir).
On s'accorde que vous pouvez aller jusqu'à 350 / 400 ohms, donc si vous avez une 150 ohms sous la main, allez-y.
@@elodiecemoi3057 merci pour ta réponse. Je l'ai soudée ce matin et comme par magie il a ressuscité d'entre les morts. Incroyable !.
Apparemment j'ai vu qu'une autre pin permettait de résoudre un autre problème.
Moi qui est plutôt pro Synology,ca me conforte dans mon idée ;) Encore merci 👍🏻
@@stivxbox Heureux pour toi ! je crois qu'on ne peut plus compter le nombre de personnes ayant sauvé leur NAS avec cette méthode (dont je fais partie !), A bientôt sur Threshold-Lovers.com
I have tried the link for the diagram but the link requires a login.
Sorry for that !
we have faced problems with th Download Manager (and we still have problems): I have change the permissions required, so you should be able to download the diagram from now.
If not, drop me an email: threshold-loversATgmx.fr andi will send it to you. Good luck with your NAS...
What is that resistor ? 200 ohm or 300 ohm ?
100 ohm
@@mameawchannel5870 I've soldered it on 1-8 pins but it still has problem and don't boot what would I do ?
@@Alivesnotalive i get slove this problem but have new problem . qnap boot not pass bios -*-" [ before make this my qnap not show on monitor ]
@@mameawchannel5870 if your NAS boots but does not pass Bios, it is maybe not only a clock issue (that you have probably fixed with the 100 ohms resistor solution) but it could be a problem with the internal battery that feeds the motherboard.
It is not sure at all, bit I would try to replace the Lithium battery (it has a "button" form factor): sometimes it brings your NAS back to life for 2$ !!
The connector diagram seems to have been removed. Could you please reup it.
I have tried to download it just now, and it works: try with another browser (with Chrome, no problem to download it), or send me your email (use the email in the "contact us" menu on the threshold-lovers.com website) and I will send the diagram to you.
100 Ohm doenst work
65 Ohm FIX the Problem !!!
But with 65 Ohm the System need 5-10 Min to Boot (Display shows all the time "BOOTING") but i can move the Data to the new NAS
The lower the resistor value, the higher the current is in the faulty transistor !
So I strongly suggest to backup your data as soon as possible !
For the other readers, I remind that this solution does not definitely fix the problem : the NAS may (will ?) die in a few days, few weeks or few months... nobody knows.
Mine a run perfectly during 18 months after the 1st problem: but at least this solution allow you to get access to your data.
Remember: a NAS is not a backup !
perfect ts-251+ is back to life, 100ohm resitor to 1 and 8 pin, and that it , thk.
Great ! am happy to count you amongst the thousands of rescued people !
But do not forget that there cannot exist any permanent fix for this problem, due to a design fault with the processor.
Consequently, sooner or later, your NAS will die: be careful to backup your data, and... think about a replacement unit in the future !
To give you an idea, mine has worked again during 2 years before dying forever, but some persons have reported a couple of months only...
:(@@elodiecemoi3057
D'après ce que j'ai pu lire (en diagonale) sur un forum le souci de boot est du à un bug dans le silicium du processeur J1900. Le problème viendrait d'une sortie du bus LPC (low pin count), un bus de discussion avec des périphériques lents comme capteurs de température, EEPROM etc...
Lors du démarrage du systèmes le Firmware dois vérifier des données transitant sur ce bus et l'échec de la communication intérromp la procédure de boot.
Pour les plus curieux, qui voudraient approfondir, le problème viendrait d'un transistor mosfet sur une sortie du bus LPC. Cette sortie a 2 transistors qui fonctionnent à tour de rôle pour "tirer" la sortie soit vers le 1 ou le 0 et un des 2 transistors faiblit avec le temps ce qui force cette sortie dans un état illégal entre 0 et 1.
La résistance ajoutée en parallèle avec le transistor défectueux vient partiellement rétablir le fonctionnement du bus LPC en permettant à l'autre transistor de fonctionner. Les niveaux logiques ne sont pas aussi propres qu'à l'origine mais suffisamment clairs pour permettre le fonctionnement, au moins pour un temps. Ceci n'est PAS un problème QNAP c"est un bug Intel (je n'ai pas la source en tête).
Malheureusement il y a batch des processeurs Atom J1900 qui ont ce bug silicium de vieillissement prématuré des transistors du bus LPC.
Je ne suis pas sûr qu'il y ait une solution définitive comme l'ajout d'un buffer pour que a sortie en question travaille avec un très fable courant par exemple.
Entièrement d'acord: tu as parfaitement décrit le problème !
Je n'ai pas non plus trouvé de solution définitive, le remède que je présente dans cette vidéo étant avant tout destiné à ne pas perdre se données et à pouvoir les migrer tranquillement...
Les autres NAS avec le même processeur (Synology et autres) ont bien sûr connu la même panne.
@@elodiecemoi3057 Après avoir fait la "réparation de fortune" avec la résistance il y a apparemment une fonction logicielle surnommée "LPC_CLKRUN#" qui permet de mettre le bus LPC en veille ce qui économiserait le vieillissement et rallongerait la durée de vie. Donc mise à jour du firmware.
Après quelques recherches il s'avère que le problème se manifeste sur plusieurs séries de CPU:
J1900 AVR54
E3800 VLI89 VLI90
Chez Intel les CPUs ont des codes de batch le "stepping" par exemple 'C0'.
Il me semble que le soucis a été réglé à partir de certains stepping et que c'est pour ça que la production de toutes les puces faible TDP a été interrompue. Je n'ai malheureusement pas trouvé plus de détails.
Sinon il y a toujours la possibilité de carrément utiliser une carte mère Mini ITX standard. la connection ver le backplane des disques durs est normalement du PCI express standard. Il faut vérifier le nombre de "Lanes" PCI express nécessaires ça change suivant les modèles (1x, 2x ou peut-être même 4x). Là il va falloir jouer avec la scie pour adapter le panneau arrière.
Liens des sources:
en.wikipedia.org/wiki/Silvermont#Erratum
superuser.com/questions/1762455/did-the-intel-j1900-flaw-get-fixed
wiki.jmehan.com/pages/viewpage.action?pageId=44695614
www.congatec.com/fileadmin/user_upload/Documents/Technical_Documents/BYT_xA30_Errata_LPC_USB_SD_Card.pdf
En particulier la section "Reason for the Failure" qui donne la liste des CPUs et Familles affectées
Malheureusement cela n'a pas fonctionné sur mon TS-251+. Il continue de ne rien afficher et le voyant rouge est allumé.
Bonjour,
Même si la solution indiquée fonctionne dans 95% des cas, il y a des cas où cela ne fonctionne pas car il peut exister 2 causes (la plus fréquente se résoud par l'installation de la résistance comme indiquée, l'autre n'a malheureusement pas de solution à ma connaissance).
Si votre TS-251 ne démarre toujours pas, il est plus que probable que vous soyez dans ce 2ème cas... et le remplacement pur et simple me semble la seule approche possible, navré pour vous...
Bien cordialement,
Vous pouvez essayer de diminuer un peu la valeur de la résistance, disons à 65 ohms (plus la valeur est faible plus le signal d'horloge est élevé): cela peut parfois résoudre le problème comme l'indique une personne plus bas...
@@elodiecemoi3057 je vais essayer, j'avais tenté de monter la valeur de la résistance pour avoir précisément 1.7V
@@elodiecemoi3057 en baissant la résistance à 55 ohms, j'ai réussi à faire démarrer le NAS ! Merci. Mais c'est juste un signe que la carte mère est encore plus au bord d'être définitivement HS...
@@vincentpaire5993 Oui ça ne sent pas très bon ... ça a permis de redémarrer et donc de sauver tes données, c'est déjà énorme, mais soit prudent: backup immédiat, et régulier si ce n'est pas déjà automatisé...