Video není dostupné.
Omlouváme se.
EVO II Enterprise: Unboxing & Walkthrough
Vložit
- čas přidán 2. 09. 2021
- Autel's EVO II Enterprise Bundle is available now! In this video, Jon McBride unboxes the new EVO II Enterprise Bundle and gives a detailed look at all of the included accessories and features.
Introduction- 00:18-00:41
Bundles- 00:41-04:58
Payload Swapping- 04:58-06:25
Accessories- 06:25-09:28
Special Features- 09:28-12:16
Smart Controller- 12:16-17:30
Outro- 17:30-18:15
To learn more about the EVO II Enterprise Bundle by contacting your local Autel Robotics dealer or visit auteldrones.com/
I am a greenhorn to the Drone environment so I'm like a sponge with these videos lol. This guy doesn't excellent job of explaining things in a very precise and tempered manner. I'm looking forward to watching more of his videos.
I love my EVO2 (V1 with the Live deck), I am a little concerned with the world wide drone changes which are just around the corner, It’s obvious that the Autel V2 Enterprise is pitched against the Mavic 2 Enterprise Advanced.
Things I like to see Autel do with their next alliteration of this package; a Peli case with integral charging (for batteries, Live deck and smart controller). Bring out the Dual 1040 radiometric camera, mark the new ships up in accordance with the new FAA/CAA/EASA regulations. Have an external port under the Evo 2 to facilitate “control” of external payloads such as the Foxfury lighting system. Massively undercut the competition.
DJI don’t want to offer much more in their package because it will go into the capabilities of the M200 and M300 Range; time for Autel to frustrate the big boys again... and hopefully they will... keep up the fantastic products and keep moving forward.
Thank You! I have V1, and I have just bought V2.
Best drone ever again!
great video i have owned several dji drone including the mavic 3 now looking to buy an altel drone soon still researching you products
Thank you for the unboxing and features video. Do you plan on creating more videos for practical application and demo of the thermal sensors and RTK? I would like to see how to adjust the 640T settings and how the radiometric workflow using the Autel IR tool works, as well as a demo for using the RTK and an NTRIP service and/or an A-RTK base station.
The Evo 2 is a really good foldable drone. So WTF such a big case?!
Same for the Evo 2 Rugged Bundle, the case is twice the size it should be!
I want the Evo 2 Enterprise, with a DJI Mavic 2 Enterprise case, that's the good size! 😉
Great video. Can use my Evo II batteries... but NOT the props or motors 😢. Can the smart controller work will all Evos (lite, nano, etc.) if they are v2 or v3?
This weekend I flew the Evo 2 Pro Ent V3 in some stronger winds, with longer arms and larger motors you would hope it would perform better then an Evo 2 Pro V1. It did not, it would slow down and drop altitude and even gave me tilt warnings instead of wind warnings. They have not even programmed the FC good for the wind, this is terrible. They need to do a serious update for the FC. I've flown my Evo 2 Pro V1s in powerful winds that wanna knock you over, nothing can take that thing out of the sky, the winds yesterday were not even close to that strong and the Evo 2 Pro Ent V3 sucked badly. It took them till June 6th 2022 before they had the final FW update that gave us dual stability on the Evo 2 Pro V1 also, thats 2 years after the drone was released. So thats how long we might be waiting before they fix things with this one. I'm starting a drone company and I can't even do serious filming with this drone because the dual stability is what got the Evo 2 Pro V1 real close to the Mavic, as far as smooth flying for filming goes. So at this time if I was doing serious filming, I would still actually be using my Evo 2 Pro V1 drone. Autel is focused on making money pushing the Evo Max 4T now and other products and is taking their time with this drone poeple spent 5K of their hard earned money on. And lastly, can we please stop beating around the bush with these useless accessories and make a drop arm like we know that that's what everyone wants. Can someone who knows electronics please rewire one of those useless accessories they give us and make a drop arm. I would be willing to pay handsomly for one.
For future versions, the swappable cameras need to be installed as easy as the top payload accessory system. Insert the connection and turn a couple of wing-nuts by hand - done! This would save in having to dismantle screws and wired connectors for the cameras. Much easier for field swaps.
Can you buy separate batteries for the controller? Is there a charging port on the controller?
Even though I will prolly not ever be able to get one of these I love the EVO, I will almost always choose Quality over Quantity. I would take the EVO I over any DJI drone.
I will be waiting for y'all to come out with the EVO Nano that will prolly be my favorite drone, after of course these Enterprise Drones.
the worst part about my experience is trying to register the drone. I have flown drones for many years but seems they have changed so much that it seems nearly impossible to find a step by step that is remotely accurate & up to date.
Thorough videos, but please up Jon's audio. I have to crank up the volume and then the next video I play is way too loud
Based on your video I purchased the EVO Pro Enterpise. Much to my surprise the Hub and 12V charger was missing. I do not believe it was taken from the box as the note "what is in the box" had these items also not mentioned. So, is there a more downgraded Enterprise Box for European customers?
I do solar farm thermal inspections. Autel NEEDS to do a software update which allows the drone to fly perpendicular to the flight path. This is an absolute must!
Won't Crusie mode in Missions work for that?
When will there be an update for EVO II V2 Jon make them RID compliant?
I just purchased my EVO II V2 Dual Enterprise and found out that it is not RID compliant.
Great video John, thanks. Can you advise the status of the live deck? Will there be a live deck released for the V2?
Still waiting on the status of that
Since the smart controller know has a HDMI port, is the Live deck even necessary? Not sure if the LD provides additional functionality...
How about swapping 640t dual with Max4t payload?
Making the switch from DJI to this drone soon but I have to say the speaker, strobe and spotlight would be E-waste as soon as I opened the case. Would immediately remove them from the kit and add additional batteries in their place. Would also trade them for one RTK module. Where is the rugged kit with a smart controller, thermal camera, 48MP optical and an RTK module, does that exist? I would imagine that setup would be appealing to many buyers not in the search and rescue field even if it was slightly more expensive.
I have always preferred Autel drones because they make the most advanced drones. But Autel has also been putting out incomplete drones, where features are not working as advertised. I have recently bought an Evo 2 Pro Enterprise V3. I have a few hundred flights and understand a little about frequencies and antennas and I will explain here to dissolve any confusion about those things. I have lots of experience with the Evo 2 Pro V1 as I have 2 of them and have done lots of comparing and troubleshooting over the last couple of years with them. The Evo 2 Pro E V3 which should have a 15km transmission I just got barely transmits as good as my Evo 2 Pro V1's, which have a 9km transmission. When you go to the transmission screen on the new Evo 2 Pro E V3, there are no options, the screen is empty, Autel has explained to me this will be done at some update, it has now been 5 months since the drone's been released. The drone is very obviously working on a 2.4Gz signal, that is a short wavelength and should have a 2 inch antenna, just like most all drones up till now. The reason the transmission is barely keeping up with my Evo 2 Pro V1s, is because they put a 4 inch antenna, which is optimal for 900Mhz frequency. 900Mhz Is a longer wave that goes better through walls, when they do the update this will be an amazing drone yes, for now, if you've had an Evo 2 Pro V1 in the past, you will feel quite dissapointed. I do get real flight times of a little over a half an hour compared to 25 minutes which everyone always exagerrates, so Autel did real good there yes. So Autel put out a new drone with supposed frequency switching, but it's not doing any of that yet and the antennas are optimized for 900Mhz, which the drone is not working on, because if it was working 15km with 900Mhz would be amazing in the city yes. Of course at 900Mhz you then get a slower waves, hence slower data transfer, so I'm not even sure if they can transmit data at 1080 at that frequency, I would be fine with 720 resolution at 900Mhz, I still see power lines good on the bright screen, right now it is 720, I can easily tell, they havent updated that either. Respectively, a 4.8Gz transmission or 5.8, would be optimas with about an even shorter antenna probably closer to 1 inch, with makes it easier to fit inside your cellphone as you go up with Ghz :-). This is a very disappointing thing that Autel is doing and I hope they do the update for the transmission soon. I paid 5k for this thing and that was one of the main reasons I bought it for. Autel has also released a new drone with something very important not working as advertised. They kept my drone in repair for weeks so I got my money back from Blue Skies, who I bought it through. I then got the same drone through Amazon and found that the feature is not working on that one as advertised either. I have considered sueing Autel but I have always liked and supported Autel, and would prefer not to do this. If Blue Skies does not end the bank case against me I will tell everyone here what this feature is a lot of people would be upset, and I would hurt Autel, I would prefer not to do this. I hope they do an update to fix this soon.
A question about the zoom: are the zoom photos saved as zoomed-in photos or is it like the DJI Mavic 2 Enterprise Advanced where the zoom photo is saved as a normal wide-angle photo?
At 6:20 you said you would not recommend changing payload "a lot". Why?
It would be nice if it came with an operators Manuel.
I have an Evo 2 and just got an intelligent controller V2, and I can't get it to work together. I email support, and it takes a day to get help. I would like someone to help me with this. Thanks
Excellent, thx for the review
how bout tell us how to turn these on and off on the controller please
Hiii how many hours chards the 1 battery of autil drone?
Hey John....is the 6kpro enterprise getting released in Asia and Australia?
I use to have many DJI Drones but you guys kicked ass with Thermal camera drone. I am going to buy NEW VERSION of Autel EVO II Dual 640T . In this case when do you guys announce AUTEL EVO 3 DUAL :D I want new better thermal camera with higher Zoom X capabilities
Any news when evo 3 comes out? I'm looking for a better zoom too. To many issues with the Mavic 3 for me to got that way. Keep waiting for news on evo 3 release date
When will we see the Mini Evo
Just answered two questions I was thinking about... swappable payloads and batteries... so nice to have this design!!!! Very economical!!! Unlike others that have 100 different aircraft of all different iterations.... why I stay with Autel!!!
Zoom... Zoom... will we be seeing a global shutter payload soon?? Or other high end camera payloads???
I want the spotlight. Where can I order one?
Know what hurts? Buying a V2 Evo 2 Pro Rugged Kit +Hub + 1 more battery + Smart Controller. Total price? $3600. Enterprise is all that + case + carbon fiber + Connection and 3 accessories price? $3750. That's a big upgrade for $150. And I'm still waiting for smart controller.
Love this drone! It looks so sexy!
Porque la versión autel evo 2 640R es más cara??
❤❤❤❤❤❤❤
Thank's God that finally professional persons joining this company. Hopefully one day Autel Robotics reaches professional customer service level. So far I tried for 4 times getting demo units and test them out - with 1.6 mln views yearly on my drone related YT channel, I was not able - they bounced me to local clerks. Huge disapointement with EU customer service.
Awesome
no Gimbal Protection? I'm little bit confused, what is the differnt between 640 T and 640 R ? You offered before the 640T with Radiometric... As a part or my work, i would prefer in the Enterprise solution more batteries instead of a Spotlight or a speaker. We are Flying over 8 h /day, so a powerfull charger is what we need. Unlucky that we can`t get any SC V1 in Europe. Good video, thumbs up!
640T is made but iray (Chinese) 640R is (Flir) both are radiometric.
@@ngaoutdoors4157 with our 640T you cant measure highest, lowest and delta Temp., no scale available for the report. Useless for commercial Inspektion of photovoltaik.
@@PixxelAir-TS That’s what I have heard about 640T
What's the difference between the 640T and the Dual R? I can't find any technical information other than it's different sensors.
I believe the 640 T is a radiometric Chinese thermal sensor & the dual R is boson flir radiometric sensor
@@copperhewitt You are correct sir! I bought 640 and then 1 week the 640 r comes out 😆
👍👍👍
Wym by buying payload?
I d like to see a new camera.
8k - 1inch one. Half inch camera doesn't work properly then the weather is not good. Or in the evening.
Is there a current lead time for availability?
Pre-ordered and received. Very nice.
Send me that link to the evo 2 spotlight
Is the spotlight pitch adjustable?
No electronic pitch only manual before flight.
Darn, I just got my Evo 2 Pro, and you show me this....
Where autel new drone trailer
Wow
Great video, but as far as I know, all packs have 2 extra batteries, 3 in total.
Question. I've had an Evo 1 for about a year, many flights out of it, love it. However recently I am not recieving an image on my phone, and the "remote control and mobile phone DISCONNECTED" warning appears, however, I can still fly the aircraft and tilt the gimbal, just no image. Any info would be appreciated, thanks
TOP...........💯
How much
This is way better than DJI mavic 2 pro.
is autel made in the usa ?
Why is it orange?? Makes it look like a toy.
Sold my Evo 2.. why? Many reasons why.
With the Surreal prices offered by autel robotics to its products it will probably be almost impossible to reach or even surpass the DJI manufacturer's level in relation to DRONES. If you continue in this exorbitant value footprint, you will be forgotten like many other companies.
Freedom Drone
Thank you for not including hard geofencing like DJI. That's the sole reason I will never buy a DJI.
3 dji fans didn't like this awesome video
Again you have shown that there's no better drone on the Market.
I bet 15,000$
THE TOP SENSORS ON ALL V3 ENTERPRISE MODELS ARE NOT WORKING AT ALL IT IS BLIND upwards. I wanted to be nice and not tell people but Autel just did an update and did not fix this. This is irresponsible and false advertising. THE SENSORS ON THIS DRONE DO NOT WORK IN ALL 6 DIRECTIONS.
완전 DJI 스펙 그대로 따라하는걸보니
완전 DJI 가 장악했군요...아쉽네
It's a shame that your update service is so pitiful and incompetent. You have left the entire Evo Lite series hanging in Europe with both the marking and the remote ID. Your DJI competition is updating even the old drones. I will never buy an Autel Robotics drone again.
This company is the worst not trailer test at all