Make sure to watch how I Sublimate on 17oz water bottles 👉 czcams.com/video/09bhZAShm9w/video.html Want to get a shout-out on this channel? Just leave a comment below with your thoughts on the video.
Thank you for doing this video. I didn’t know that I could take a peek, and tape it back down, and press it again. Thank you! Now, I think I can press perfect tumbler edges. Merry Christmas 2023!
Thanks for your well wishes and your comments and support. Yes please, I always take a peek before I fully pull it off because once you do pull it off there is no lining back up.
Very nice job. Based on the quality of videos I see this man should be rich by now. Don’t just take quality give in thankfulness. Great job again ATPrints
Thanks for your comment. It will all come together. Just make sure to get the correct measurements and pay closer attention to the taping around the top and bottom. What I will also say is that with the mug press sometimes no matter what you might get a seam but with an oven all of that goes away. Please dont give up and if you have anymore questions you can ask me or you can reach out to me on IG or facebook for help. The links are in the description.
Thanks for your comment. Yes, I think doing the top and bottom is important. Some persons get lucky with not doing the taping but what I can recommend is to apply a lot of pressure when you are taping the top and bottom and everything should go great.
HELLO, I'M NEW TO SUBLIMATING TUMBLERS, I'M TRYING TO FIGURE OUT WHAT HEAT SETTINGS AND MINUTES I NEED TO DO USING A MUG PRESS I HAVE AND A CONVECTION OVER. I MESSED UP 2 TUMBLERS IN BOTH. TUMBLERS NOT CHEAP. WHY ARE TUMBLERS SO HIGH?
Hey Thanks for your question and welcome to sublimating tumblers. There are two ways you can sublimate your tumblers. Firstly you have the Mug press which you asked about setting. FOr the mug press you can use 365 F for 70 seconds. Remember when those 70 seconds are completed you need to turn the tumbler so the other side can be sublimated. If you are using an convection oven you can use between 450F and 400 F. I personally use 480F for 5 minutes. You can watch this video which explains how to use the convection oven and settings when sublimating 👉 czcams.com/video/_bAvTbA3RKg/video.html In relation to tumblers been expensive, I believe there are in high demand but it also depends on where you get them from. If you need some you can reply to this comment and i will provide you with a link where you can get some. I hope this helps.
HI, I am sorry but once you sublimate onto the item you can not change or redo the wording unless you strip the entire tumbler by sanding, repainting, and coating it with polygloss, then you can sublimate it. If you are interested in that method, it's a process but it works. I have a video on my channel that can help. czcams.com/video/NlaVpag3qIA/video.html
@@tonycarrington6994 Thanks for your comment. I always mirror my image. Remember you have act least two ways to mirror you design. You can do it in your program or you can select the option on your printer so that it always mirrors the image for you.
Thanks for your question and sorry for the late response. There are different prices ranging between $349.95 up to $549.95. Please see the link where you can choose which one you like 👉shrsl.com/3k8w4. The name of this press is the HPN Signature Series 7-in-1 Automated Sublimation Mug and Tumbler Press. If you ask me which one to choose I would advised the 7 in 1 because it comes with all the attachments
Make sure to watch how I Sublimate on 17oz water bottles 👉 czcams.com/video/09bhZAShm9w/video.html
Want to get a shout-out on this channel? Just leave a comment below with your thoughts on the video.
Thank you for doing this video. I didn’t know that I could take a peek, and tape it back down, and press it again. Thank you! Now, I think I can press perfect tumbler edges.
Merry Christmas 2023!
Thanks for your well wishes and your comments and support. Yes please, I always take a peek before I fully pull it off because once you do pull it off there is no lining back up.
I love tumblers!
I love tumblers.
Thanks for your support 🎉
Very nice job. Based on the quality of videos I see this man should be rich by now. Don’t just take quality give in thankfulness. Great job again ATPrints
Wauuuu, really love it.
The explanation was very Clear. I did learn you don’t have to tap it up or down.
Going to share it.
Thank you very much.
Glad it was helpful! and thanks for your support.
I am new to sublimation and I really like the way you explain everything. Although I am having lots of
problems and the seam, top and bottom.
Thanks for your comment. It will all come together. Just make sure to get the correct measurements and pay closer attention to the taping around the top and bottom. What I will also say is that with the mug press sometimes no matter what you might get a seam but with an oven all of that goes away.
Please dont give up and if you have anymore questions you can ask me or you can reach out to me on IG or facebook for help. The links are in the description.
Awesome work Allan … Loving the look and the designs of these tumblers. A.T Prints never disappoints guys..get your tumblers done ASAP!!🔥🔥
Thanks for your comment and support. 👍🏽👍🏽
Great teacher. Beautiful design. Love it
Thanks so much for your support and comment.
CAME OUT GREAT!!!!!!!!!!! Great teaching
Your welcome and I am happy to hear your success.
NICE!
Keep up the good work.
Thanks very much.
You're quite welcome.
Hopefully I'll be trying this for the first time tomorrow.
@@empresst3084 well I want to wish you all the best and feel free to send pictures or ask questions if you need to.
@@atprintsAww... Thank you so much. Okay, I will.
I was thinking you never taped the top and bottom
As I have been having probs doing it that way and yours came out with a nice even bottom
Thanks for your comment. Yes, I think doing the top and bottom is important. Some persons get lucky with not doing the taping but what I can recommend is to apply a lot of pressure when you are taping the top and bottom and everything should go great.
good morning everyone! I am about to do my first tumbler I have watched many videos but this one is explained clearly. I will come back with an update
Thanks very much. I’m looking forward to hearing your great results.
I love MakerFlo! You did such a good job with this video, thank you!
Thanks so much for your comment, I appreciate it.
lovee them better
Thanks 😊
And can I ask where you got the thing you had the tumbler on rotation?
Thanks for your question. Here is the link 👉 amzn.to/3n4ifch
I like them but I think the color should be richer. But thank you for sharing
Thanks for comment. I do think the can be richer in color also.
HELLO, I'M NEW TO SUBLIMATING TUMBLERS, I'M TRYING TO FIGURE OUT WHAT HEAT SETTINGS AND MINUTES I NEED TO DO USING A MUG PRESS I HAVE AND A CONVECTION OVER. I MESSED UP 2 TUMBLERS IN BOTH. TUMBLERS NOT CHEAP. WHY ARE TUMBLERS SO HIGH?
Hey Thanks for your question and welcome to sublimating tumblers. There are two ways you can sublimate your tumblers. Firstly you have the Mug press which you asked about setting. FOr the mug press you can use 365 F for 70 seconds. Remember when those 70 seconds are completed you need to turn the tumbler so the other side can be sublimated.
If you are using an convection oven you can use between 450F and 400 F. I personally use 480F for 5 minutes. You can watch this video which explains how to use the convection oven and settings when sublimating 👉 czcams.com/video/_bAvTbA3RKg/video.html
In relation to tumblers been expensive, I believe there are in high demand but it also depends on where you get them from. If you need some you can reply to this comment and i will provide you with a link where you can get some.
I hope this helps.
@@atprints Thank You. I will look at the video after work. Maybe on break if I have time.
@@rhondathomas6773 you are welcome
Hey can I get the link to the tumblers site
hi how can i fix all the lettering comes out backward thanks
HI, I am sorry but once you sublimate onto the item you can not change or redo the wording unless you strip the entire tumbler by sanding, repainting, and coating it with polygloss, then you can sublimate it. If you are interested in that method, it's a process but it works. I have a video on my channel that can help. czcams.com/video/NlaVpag3qIA/video.html
@@atprints make sure to mirror your image when printing your design 👍
@@tonycarrington6994 Thanks for your comment. I always mirror my image. Remember you have act least two ways to mirror you design. You can do it in your program or you can select the option on your printer so that it always mirrors the image for you.
What is the brand of the tumbler heat press? How much does it cost
Thanks for your question and sorry for the late response. There are different prices ranging between $349.95 up to $549.95. Please see the link where you can choose which one you like 👉shrsl.com/3k8w4. The name of this press is the HPN Signature Series 7-in-1 Automated Sublimation Mug and Tumbler Press.
If you ask me which one to choose I would advised the 7 in 1 because it comes with all the attachments
I’ve been trying and cannot get rid of that seam and he doesn’t put tape around edges I think I’ll try this … thx u
Take it one step at a time and it will come together. If you are still having challenges just let me know what they are and i will try to assist.
How much do you sell them for
In my country, they are sold for between 30-40 US dollars.
Ah yes a bajan!🇧🇧🇧🇧
👍🏽