glad to hear you say it, KBs passing wasn’t the end of Hoonigan. all the boys became re-engaged with what Hoonigan was supposed to be like, and we started to get amazing content again. then the big wigs shut it all down. just glad that we are getting that same passion in everyone’s individual channels now.
Please don’t stop on the M3 track car content. The growing pains and heartache are probably some of the most important parts of an expansive build like this that don’t get shown enough. But this is the reality, you build a car like this, test it, diagnose issues, fix it, and then repeat the process until you are confident in the vehicle. And I greatly appreciate you bringing us along for the ride!
Bad Daddy Braddy!!!!! Vin most of us have been following since the hoonigan days. Seriously glad that you, Zack, and Brad are keeping the real meaning of what hoonigan was alive for us true fans. Would love to see Danger Dan roll thru one day.
16:50 Tell me you're not a mechanic without telling me you're not a mechanic. I'll just slide to head gasket surface across the concrete floor for no apparent reason. 🤣
@@Notdb1gabe Both heads should go and combustion chambers measured so as to mill the minimum off as possible. Sliding it across a dirty concrete floor could put an unnecessarily deep gouge in it that requires more material to be removed. Since only one head is off that could result in slightly different cylinder pressure on that bank. Plus the head might have been perfectly fine and not have required any surfacing. Anyway you look at it, it was a bad move. I'd never do it.
I would go back and talk to smedding about this. They tuned it and built the motor so they would be the best person tell u. If they let it rev to 6900 and they didn't put proper valve spring for u to rev that high that would kinda be a blunder on them. Also good for them to know so it doesn't happen to their future motors
Yeah they kinda let him down honestly. The damage wasn't because of fuel leaning out or lack of oil, not "operational error" per se. This is more technical issue where the valve floats and got hit by the piston, Smedding should've accounted for it.
I don't know if E85 does the same thing that methanol-powered engines do, but if it attracts water, and they let the engine sit, the contaminated oil (oil always gets fuel contamination, no matter what) could have attracted moisture to the valve spring, and if the spring had a weak spot/defect, it could have corroded. then when he fired the car up after sitting for years, it was just a matter of time before it broke. an image autopsy of the broken spring will tell on this. also, there's a Steve Morris video about this exact problem with methanol engines and sitting. apparently methanol is WAY more nasty though. part of the fix is, don't let an E85 fueled engine sit for long periods of time. or if you need to, run it on ethanol free gas for a while and change the oil before storing it.
I agree that after kens passing Hoonigan was back on the upswing pretty quickly. The project garage videos were as Hoonigan as it got. And i was sad too see it get canned. Glad to see that kind of content live on with Vin though. The spirit of Hoonigan lives on with the boys.
Vin, I mean this honestly. Your channel is really something special. Your production value is top notch and your content is always on point. You don't stay on one bit of content every week. You rotate your topics and try new things. I love it! Thursdays are becoming a day I look forward to now
Anyone whos owned, modified and wrenched on things with a motor always has that one project that just fights you through it's entire existence. I think the struggle car balances out the channel. There should always be a struggle car that infuriates you and illustrates that aspect of the hobby/life. Keep showing the grit and determination thats needed to see a tough project through and how it can be an emotional rollercoaster. That's a real part of being a car guy!
Man it feels good to see Brad again. And I bet it feels good to be with friends you can trust and just chop up with and catch up on life.. You know what doesn't have valve spring issues? Rotaries!? 😂
Thanks for being genuine about the build. And.... You're right, CZcams doesn't show the growing pains. Keep the channel on your current vibes, it's refreshing and awesome to watch.
This became pure deja vu about halfway in. Memories helping my friend pull the heads off his C5 to find bent valves and marred pistons. Happy to see you not have to go too deep into it though!
The content you’ve been pumping out is absolute gold! Keep up the great work! This is honestly the best, most laid back, genuine car content I’ve seen in a while.
Dude! Great episode! Thank you for the update on the M3. Glad it's an easy fix. I'm ready to see you respectfully romp on it at the track. Also I'm just happy to help support in any way I can. Also loved the call back to Ken. Beautiful clip of an awesome man. Looking forward to next Thursday my guy. See you then. ✌️
When I first saw the M3 in person at Gridlife Laguna Seca…by far favorite car all weekend. I think it was due to watching the trials and tribulations of this car and seeing you lap it made me so happy!
Bro this whole build series over all this time has been amazing. So stoked to see you’ve found the issue. Absolutely love this channel. Your content has been top notch no matter the subject. Always look forward to the Thursday uploads. Keep it up vin 🤙🏼
Love the breakdown of all the issues with the E36 and the attempts to fix. It's nice to see a "true" portrayal of project car life. Much different that most of the other CZcams car channels. Keep on keepin' on and I will keep watching and giving the ol thumbs up!
Wow, lot going on in this episode. RIP KB. I followed him for a long time. Being a course marshal for Stage and TSD rally competitions, we crossed paths a couple times. Favorite build was the RaptorTrax. I think Hoonigan did some great things, but I also think it had run its course. But at the same time it freed you up to get back to driving cars instead of a desk. And after seeing some of the old highlights, you look better without the full beard. 🤣
11:48 That’s exactly what has happened to numerous LS engines that I know of including the LS engine on my 03 Yukon it was burning lean and that is a known problem with these engines
I feel you bro, I have 7 project cars right now. I live remote miles from my friends, no one will help me... I've spent the last 10 years trying to finish them. I have an e90 330i track car I'm trying to finish and an Escort Cosworth... I get close to the end and then its a slug to get them done... I literally have nothing left to give. Plus I just bought a Maserati as my new daily with the F1 gearbox and having so much fun in that like you are in the 360
Brad is definitely not a hack, he's the friend that comes through when car issues arise & with knowledge and he makes the issues seem insignificant with his confidence and getting it fixed.....Great dude 👍🏽 Great video and update on the car Vin 👍🏽
Keep the highs and the lows content coming. It is a much closer representation to what all of us car guys go through. Also, side note, going to pick up a gen 1 Raptor today!
You're the first to say the event was pulled & the channel for the builds culled. That explains so much! Fuck that, no wonder you all left... The old corporate greed whilst everything runs on a tight budget. Loving what you're all doing now though.
Great video! Thank you for not using clickbaity/ red / mr beast style thumbnails and focusing on just great content. Good stuff! Excited to see what else comes
Such a humble guy. Great episodes. Vin, previous track toy was my 240Z with an LS. Stuck it in a lamp post, wish all I had to do to repair that was a valve spring but that was entirely bent car not just a valve 😂
So stoked to see this requires such a simple nothing fix. This is/will be my favourite car of yours to see content on, besides the GTI. I absolutely love this M3, and it's really one of my favourite sounding cars ever
vote for sending the car over to Chase, getting them to sort it and vlog the whole thing. All for smashing it back together with new found motivation, but the car is still in it's infancy, there will be more development.
If you want less “heavy maintenance” like your into atm once she’s back together don’t rev it out quite so high. Give the hardware a 500-1000rpm “buffer” aka lower rpm limit. You’ll sacrifice some power/rev range but she’ll live much much longer. 🎉 party on in that bmw
Feel your pain, my E92 325i has just died, misfire, low compression, timing out. For sale if anyone in the UK 🇬🇧 interested. Lost interest in it and went back to a GTI 😎. Great content on this channel, keep up the good work bud 👍
Keep posting this content! Loved it myself! I love seeing all the steps from start to finish. You at least found the issue and you know what you need to do for the repair. So now I'm just waiting for that repair video lol
I was kind of surprised that you called in support given all the engines and cars you’ve worked on, but I also understand doing so. It’s always a confidence builder when you have a tenured mind in the room. Can’t wait to see you ripping in this thing again soon. You’ve inspired me to get my Firebird Formula out and row some gears this afternoon. Take care, Vin. Looking forward to the next vlog!
Shit, you deserve all the love.We're happy to be around as you do this. Honestly You could stand the upload more, it aint gotta be high quality. We will be happy to watch anything you post.
HELL YEAH!!!!😅GLAD TO SEE BAD DADDY ON HERE TOO!!!!YOUR A GOOD DUDE VIN...NOW JUST GATHER THE REST OF THE SCUMBAGS AND GIVE US WHAT WE WANT!!!!WHERE,S SCOTTO !!!!!!!! SCUMBAGGARY AT ITS FINEST!!!!!HERT WHERE YOU AT BRO!!!!!WE NEED SOME NAPPY UP IN HERE TOO!!!!!I EVEN WATCHED THE ADDS ON HERE BRO!!!!YOUR WELCOME 😅
Probably one of the coolest episodes just cause all the OG hoons in it especially having brad in it super epic love great job man your literally carrying the hoonigan vibe along with Zack tbh are boy hert a let down feel no energy and love gose into that channel like how you do one yours love my boy hert but he don't love to vlog and edit
Surely I can't be the only one left hanging on the gymkhana grid builds and the VERY necessary actual races that still need to happen? Pretty please make it happen dude
Thursday's are my favorite because of your videos Vin! Even the "bummer" episodes are enjoyable and show, in my opinion, the parts of car building that really make it rewarding. The blood, sweat and tears all all part of it!
Love you Vin, can t wait to see where your story goes, my boys are to young, but I can t wait to show them some of the quality car content on youtube, mainly yours!
Use code VIN50 to get 50% OFF your first Factor box plus 20% off your next box at bit.ly/3wHuNek!
glad to hear you say it, KBs passing wasn’t the end of Hoonigan. all the boys became re-engaged with what Hoonigan was supposed to be like, and we started to get amazing content again. then the big wigs shut it all down.
just glad that we are getting that same passion in everyone’s individual channels now.
Please don’t stop on the M3 track car content. The growing pains and heartache are probably some of the most important parts of an expansive build like this that don’t get shown enough. But this is the reality, you build a car like this, test it, diagnose issues, fix it, and then repeat the process until you are confident in the vehicle. And I greatly appreciate you bringing us along for the ride!
BMW'S HAVE JUNK ENGINES.. 😂 F THAT
good to see Brad
This has easily become my new favorite car channel
Agree!!
Same!
Fr
Same!
Same!!! love the content
Bad Daddy Braddy!!!!! Vin most of us have been following since the hoonigan days. Seriously glad that you, Zack, and Brad are keeping the real meaning of what hoonigan was alive for us true fans. Would love to see Danger Dan roll thru one day.
Man story time took me back. Good old days.
Ditto. Thanks Vin for being as detailed as possible on the history 🤘🏽
Anyone else wince a bit when he started hammering the valve spring with the heads mating surface face down on the shop floor? lolol
Yes hahahaha
Oh my gawd bruh. That move hurt my soul...
16:50 Tell me you're not a mechanic without telling me you're not a mechanic. I'll just slide to head gasket surface across the concrete floor for no apparent reason. 🤣
Head has to go to machine shop and get resurfaced anyway 🤷🏽♂️
@@Notdb1gabe Both heads should go and combustion chambers measured so as to mill the minimum off as possible. Sliding it across a dirty concrete floor could put an unnecessarily deep gouge in it that requires more material to be removed. Since only one head is off that could result in slightly different cylinder pressure on that bank. Plus the head might have been perfectly fine and not have required any surfacing. Anyway you look at it, it was a bad move. I'd never do it.
@@ConstitutionalFreedomFighter good thing it’s not your build then 😅
@@Notdb1gabe Agreed 😁
Bruh, I know! Cringed so hard. Why not do it on a more agreeable surface. OMG!
I would go back and talk to smedding about this. They tuned it and built the motor so they would be the best person tell u. If they let it rev to 6900 and they didn't put proper valve spring for u to rev that high that would kinda be a blunder on them. Also good for them to know so it doesn't happen to their future motors
Yeah they kinda let him down honestly. The damage wasn't because of fuel leaning out or lack of oil, not "operational error" per se. This is more technical issue where the valve floats and got hit by the piston, Smedding should've accounted for it.
I don't know if E85 does the same thing that methanol-powered engines do, but if it attracts water, and they let the engine sit, the contaminated oil (oil always gets fuel contamination, no matter what) could have attracted moisture to the valve spring, and if the spring had a weak spot/defect, it could have corroded. then when he fired the car up after sitting for years, it was just a matter of time before it broke.
an image autopsy of the broken spring will tell on this.
also, there's a Steve Morris video about this exact problem with methanol engines and sitting. apparently methanol is WAY more nasty though.
part of the fix is, don't let an E85 fueled engine sit for long periods of time. or if you need to, run it on ethanol free gas for a while and change the oil before storing it.
You and Zac are making the best car content anyone could ask for! Makes me want to work on my junk more!
I agree that after kens passing Hoonigan was back on the upswing pretty quickly. The project garage videos were as Hoonigan as it got. And i was sad too see it get canned.
Glad to see that kind of content live on with Vin though. The spirit of Hoonigan lives on with the boys.
Vin, I mean this honestly. Your channel is really something special. Your production value is top notch and your content is always on point. You don't stay on one bit of content every week. You rotate your topics and try new things. I love it! Thursdays are becoming a day I look forward to now
$25k for a 40k mile alpine m3 makes me sick
Unreal
@@vin_tra I paid that for my 13' 335is in 2019 lol
just did a quick search for one (in the Netherlands) cheapest one manual got 279.000km on the clock base spec and it's listed at 34k.....
The 92 on OfferUp for less than 30racks?? That’s a goddamn that’s the deal of a lifetime
The 92 on OfferUp for less than 30racks?? That’s a goddamn that’s the deal of a lifetime
Anyone whos owned, modified and wrenched on things with a motor always has that one project that just fights you through it's entire existence. I think the struggle car balances out the channel. There should always be a struggle car that infuriates you and illustrates that aspect of the hobby/life. Keep showing the grit and determination thats needed to see a tough project through and how it can be an emotional rollercoaster. That's a real part of being a car guy!
New Vin video. It's a good day
Hell yeah! Fav day of the week!!!
Brad coming in clutch to ease the pain and relief some anxiety!!!
Man it feels good to see Brad again. And I bet it feels good to be with friends you can trust and just chop up with and catch up on life.. You know what doesn't have valve spring issues? Rotaries!? 😂
17:40 only when it's heartache do we get episodes of repair!
Nice to see Brad still around y’all Vin
Brads that bro everyone needs in their life.
Your story telling ability is unlike most channels, so cool to see your channel blow up!
Thanks for being genuine about the build. And.... You're right, CZcams doesn't show the growing pains. Keep the channel on your current vibes, it's refreshing and awesome to watch.
This became pure deja vu about halfway in. Memories helping my friend pull the heads off his C5 to find bent valves and marred pistons. Happy to see you not have to go too deep into it though!
The content you’ve been pumping out is absolute gold! Keep up the great work! This is honestly the best, most laid back, genuine car content I’ve seen in a while.
You need to make a video of your house renovation! I love the mid mod aesthetic so much!
Dude! Great episode! Thank you for the update on the M3. Glad it's an easy fix. I'm ready to see you respectfully romp on it at the track. Also I'm just happy to help support in any way I can. Also loved the call back to Ken. Beautiful clip of an awesome man. Looking forward to next Thursday my guy. See you then. ✌️
When I first saw the M3 in person at Gridlife Laguna Seca…by far favorite car all weekend. I think it was due to watching the trials and tribulations of this car and seeing you lap it made me so happy!
Bro this whole build series over all this time has been amazing. So stoked to see you’ve found the issue. Absolutely love this channel. Your content has been top notch no matter the subject. Always look forward to the Thursday uploads. Keep it up vin 🤙🏼
I was working in a T-shirt tent in glamis and bumped into Brad. Super cool dude.
Great content! So good to see Brad too. Keep bringing him on please. So happy to hear about the minimal damage.
Love how Zack and yourself both post on the same day. Some cultured car based content for my chill time after work.
Thankyou.
Even though I haven’t followed the journey of the E36 I still absolutely love it and I hope to see some tracks videos once sorted.
Glad you're finishing it! You've come so far it would suck to not get some kind of satisfaction form the build. Looking forward to seeing it rip!
another Banger! Laughed, Cried, searched FB marketplace!
hahaa i swear every time i watch one of Vin's videos or other car dudes, i go straight to craigslist or FB marketplace. why am i like this, hahaha
Love the breakdown of all the issues with the E36 and the attempts to fix. It's nice to see a "true" portrayal of project car life. Much different that most of the other CZcams car channels. Keep on keepin' on and I will keep watching and giving the ol thumbs up!
Wow, lot going on in this episode. RIP KB. I followed him for a long time. Being a course marshal for Stage and TSD rally competitions, we crossed paths a couple times. Favorite build was the RaptorTrax. I think Hoonigan did some great things, but I also think it had run its course. But at the same time it freed you up to get back to driving cars instead of a desk. And after seeing some of the old highlights, you look better without the full beard. 🤣
That Mk4 R32 in the background looks so sick on those wheels
11:48 That’s exactly what has happened to numerous LS engines that I know of including the LS engine on my 03 Yukon it was burning lean and that is a known problem with these engines
Love seeing the homies. Zack, Ron, and the man bad daddy Braddy. Also, love your background music choices.
I feel you bro, I have 7 project cars right now. I live remote miles from my friends, no one will help me... I've spent the last 10 years trying to finish them. I have an e90 330i track car I'm trying to finish and an Escort Cosworth... I get close to the end and then its a slug to get them done... I literally have nothing left to give. Plus I just bought a Maserati as my new daily with the F1 gearbox and having so much fun in that like you are in the 360
Brad is definitely not a hack, he's the friend that comes through when car issues arise & with knowledge and he makes the issues seem insignificant with his confidence and getting it fixed.....Great dude 👍🏽
Great video and update on the car Vin 👍🏽
Love Brad. Please keep checking in with him. I know he has a channel but he is the seasoning on a good meal.
If that makes any sense at all....
Your personality is what gets the views. You’re a good one V
Keep the highs and the lows content coming. It is a much closer representation to what all of us car guys go through. Also, side note, going to pick up a gen 1 Raptor today!
Stoked to see more content on this car, this is every e36 owners dream car ❤
I'm always so excited for a new video on Thursday. Great to hear that it could be a straightforward fix.
Keep the E36 time attack car! It’ll be worth it in the end! Missing the S14, buy it back it would make great content! Love the content Vin!
I'm just glad your showing the ruff with the smooth stick with it then cars going to be mint
You're the first to say the event was pulled & the channel for the builds culled. That explains so much! Fuck that, no wonder you all left... The old corporate greed whilst everything runs on a tight budget. Loving what you're all doing now though.
Great video! Thank you for not using clickbaity/ red / mr beast style thumbnails and focusing on just great content. Good stuff! Excited to see what else comes
Such a humble guy. Great episodes. Vin, previous track toy was my 240Z with an LS. Stuck it in a lamp post, wish all I had to do to repair that was a valve spring but that was entirely bent car not just a valve 😂
'Story-Time is a good idea. Brings everything into context. 👍🏻
"When you're on a budget, you're on a budget" has never rung so true. Good seeing Bad Daddy Braddy
So stoked to see this requires such a simple nothing fix. This is/will be my favourite car of yours to see content on, besides the GTI. I absolutely love this M3, and it's really one of my favourite sounding cars ever
Gti content soon!
@@vin_tra can’t wait!!
vote for sending the car over to Chase, getting them to sort it and vlog the whole thing. All for smashing it back together with new found motivation, but the car is still in it's infancy, there will be more development.
King Hack is wild... and accurate
I honestly had no idea who you was before this channel and now I watch and enjoy everything, keep up the good work 👍🏼
Seeing Kato really brings back the DT vibes.
If you want less “heavy maintenance” like your into atm once she’s back together don’t rev it out quite so high. Give the hardware a 500-1000rpm “buffer” aka lower rpm limit. You’ll sacrifice some power/rev range but she’ll live much much longer.
🎉 party on in that bmw
Feel your pain, my E92 325i has just died, misfire, low compression, timing out. For sale if anyone in the UK 🇬🇧 interested. Lost interest in it and went back to a GTI 😎. Great content on this channel, keep up the good work bud 👍
Keep Brad around. Knowledge always been a1
Keep posting this content! Loved it myself! I love seeing all the steps from start to finish. You at least found the issue and you know what you need to do for the repair. So now I'm just waiting for that repair video lol
Love those shop pans on all the parts and tools!
"You get more kiss marks on new years you're good" fucking hilarious
Not the first bad daddy cross over i expected, but love Brad content
With the quality of your content you deserve way more subs. Happy to have been here since the start.
I was kind of surprised that you called in support given all the engines and cars you’ve worked on, but I also understand doing so. It’s always a confidence builder when you have a tenured mind in the room. Can’t wait to see you ripping in this thing again soon. You’ve inspired me to get my Firebird Formula out and row some gears this afternoon. Take care, Vin. Looking forward to the next vlog!
I really like this video - It’s REAL car build content and comes across very cool
Thanks for the KB tribute!
“Be creative & don’t be an A-hole “!
Brad. Says he cant work anymore.
Also Brad. Working on cars.
Something never change 😂
Hell yeah brotha. Don't give up on this thing. It will reward you in the end!
Vinny doesn’t pay for parts and has other people install them. Everybody has that one friend with no shame.
Man see new vin video, man happy. Thanks Vin.
good seeing brad back with yall
Shit, you deserve all the love.We're happy to be around as you do this. Honestly You could stand the upload more, it aint gotta be high quality. We will be happy to watch anything you post.
Keep up the good work Vin, been watching you and the Hoonigan boys for years, and good to see you thriving bud, cant wait for the next one
HELL YEAH!!!!😅GLAD TO SEE BAD DADDY ON HERE TOO!!!!YOUR A GOOD DUDE VIN...NOW JUST GATHER THE REST OF THE SCUMBAGS AND GIVE US WHAT WE WANT!!!!WHERE,S SCOTTO !!!!!!!! SCUMBAGGARY AT ITS FINEST!!!!!HERT WHERE YOU AT BRO!!!!!WE NEED SOME NAPPY UP IN HERE TOO!!!!!I EVEN WATCHED THE ADDS ON HERE BRO!!!!YOUR WELCOME 😅
Vin! I actually appreciate this kind of content. It's real, cars are amazing and fun, but sometimes they're a giant pain in the ass.
This is what happens when you fire the parts cannon at something and skip basic diagnostics. Glad you have gotten resolution to your issue.
Probably one of the coolest episodes just cause all the OG hoons in it especially having brad in it super epic love great job man your literally carrying the hoonigan vibe along with Zack tbh are boy hert a let down feel no energy and love gose into that channel like how you do one yours love my boy hert but he don't love to vlog and edit
Surely I can't be the only one left hanging on the gymkhana grid builds and the VERY necessary actual races that still need to happen? Pretty please make it happen dude
The r32 is so clean… cant stop looking
Right, and everyone is looking for a skyline lol, ive always wanted one too #wrongR32
thanks :)
Nice 👍you got lucky with that valve not causing too much damage, cant wait to see it back together and mobbin down the track
Great video! I also started over and going to school at the age 34 and your videos help me realize that I can do it! Keep up the videos man!!
Heartwarming to see Brad on the channel, its like old times.
Absolutely crushing it on your YT journey so far! Don’t lift!
Thursday's are my favorite because of your videos Vin! Even the "bummer" episodes are enjoyable and show, in my opinion, the parts of car building that really make it rewarding. The blood, sweat and tears all all part of it!
Go Vin. Keep going with the direction your doing right now. Another great vid.
Glad you finally caught a break with this bad girl lol can't wait to see this thing rip the way she's supposed to... And maybe some track times
Much love Vin...always a pleasure and appreciate all the work you do for a great channel!
Vins more of a man than me... I wouldn't have been able to shift either the S14 or the E46, ESPECIALLY the 14 man 😭🔥🔥
Love you Vin, can t wait to see where your story goes, my boys are to young, but I can t wait to show them some of the quality car content on youtube, mainly yours!
Seeing that s14 again.......I loved that build. I wonder if the person who won it still has it.
Woohoo!!!!! That’s about the best news you could have gotten. Makes you feel better about the diagnosing too, couldn’t have fixed that at the track
These videos are by far my favorite car content this channel is going to blow up
Vin please make a video on your F80. It’s one of my favourites from your collection and I see it doesn’t get much screen time
Love these videos Vin. Keeping it real is a breath of fresh air 💪🏼
Easy fix brother, you got this! Can't wait to see it back on track.
Hell yeah good morning vinnie. Have a killer week bud
Loving your content! Cant wait to see the 6spd swap in the the 360 🎉