@@MdMohsin-lv1tz yea that is the perfect combo. 1.1mm orifice with an mjjc foam pro and youre good. The highest foaming soaps I’ve used are 1. DIY Detail incredible suds 2. Mirror Finish polished Atomic Bomb 3. Adams Mega Foam
The actual point of the foam cannon is the make it easier to wash your car while in direct sunlight. If you have proper output, the foam should be thick and stick on the surface. This makes it so by the time you’re halfway around the car, the other half is still foamed and protected from the hot rays of the sun, reducing the chance of streaking or water spotting.
Well that's one reason.. another is for a pre wash, you should foam, let it sit then rinse, foam again then wash. I do rinseless washes now though wayyyy more time efficient drying feels way slicker
When I changed to 1.1 mm orifice my pressure washer started "oscillating". Great foam for 3 seconds and pressure drop for the second. Then great foam for 3 seconds and down pressure again. Like a waive pattern. What is causing that?
The active 2.0 and the Ve52 it’s recommended not to use the 1.1 mm office though from what I’ve read? It make the pressure washer surge since it’s not made for to be used with a 1.1
My dad just bought a 2023 Dacia Duster and he takes it off-roading sometimes but it gets dirty really quickly, any tips on what products I should start out with to clean the car?
I would deep clean and polish the paint up then ceramic coat it. It lasts about a year and all you need is to rinse off the car with water. When it starts to fade off in some spots, you can use a detailling spray that has ceramic in it to touch it up and make it like new! Id reccomend watching some videos from chemical guys channel. They go in depth of how to take care of your vehicle :)
It's the 1.1 mm orifice a smaller or bigger diameter than the orfice that's already inside of the foam Cannon thing? The orifice on the phone Cannon thing that I have looks like the hole is bigger than the 1.1 mm that I ordered on Amazon after watching this video.
You aren't getting 2 gpm on most electric pressure washers, nor is it needed. For some reason obsessed garage got everyone to think that you need more water. It might save a little time, but only very little time, and your water usage will increase. As far as cleaning ability, it really isn't all that important to hunt down an especially high flow pressure washer, unless you're in a high volume detailing environment.
Hey can you guys make a super high quality 1/2” quick connect like you do for the m22 adapters hard to find good quick connects made with quality stainless steel
@@mckillans I would love to 1. Have better products in the market such as the ones you provide, 2. Support your business if you decide to start developing that or release that product make a video and I’ll be your 1st customer 😂
Hell yeah! But only use around 1000 psi, you dont need much pressure to get good foam or to clean a car. Gas powered tend to be significantly more powerful than electric, be careful not to damage the relatively sensitive vehicle surfaces.
So bad advice , you risk a lot with foam cannons , sun , waterspots, buckets methode with pre spray ikfoam is fast , same result, hope you guys take note
Not true detailers would rather have quality over quantity because the better the vehicle is cleaned the better the chances to gain potential customers through that customer would reference friends and family relatives to call and book car detailing appointments but for some who just wants to clean their car is up to them to use a foam cannon or not
I have a 1.2 GPM electric pressure washer and an MJJC foam cannon with a 1.1mm orifice and I get great foam.
How bro...
@@MdMohsin-lv1tz Good foam cannon and 1.1mm orifice.
@@MdMohsin-lv1tz yea that is the perfect combo. 1.1mm orifice with an mjjc foam pro and youre good. The highest foaming soaps I’ve used are
1. DIY Detail incredible suds
2. Mirror Finish polished Atomic Bomb
3. Adams Mega Foam
Does the 1.1 come installed already?
@@gonzalesa101 It has the 1.25 installed but also includes a 1.1 orifice. You just need to switch them out.
E46 pre-facelift front with the M bumpers looks so damn good, its an art piece.
it's nice car
Love the e46 m3
It does look good but personally like the e46 330i zhp the best but I know you get an extra 100hp with the m3
Love my m3. Wouldn’t get rid of it for anything.
@@rumblegaming6397 Wrong answer.
The actual point of the foam cannon is the make it easier to wash your car while in direct sunlight.
If you have proper output, the foam should be thick and stick on the surface. This makes it so by the time you’re halfway around the car, the other half is still foamed and protected from the hot rays of the sun, reducing the chance of streaking or water spotting.
Well that's one reason.. another is for a pre wash, you should foam, let it sit then rinse, foam again then wash. I do rinseless washes now though wayyyy more time efficient drying feels way slicker
Plus there's no excessive water in the door jams, feet stay dry, don't need to take a hose/ pressure washer etc..
That's actually doing a heap of damage.
@@robertsaca3512 what is? LOL
@@jh.f30
Forgive me but how do you go about doing a rinseless wash ?
Thank you, my carnever looked , so good
Thanks all Good
keep up the good work
This channel is elite🔥
When I changed to 1.1 mm orifice my pressure washer started "oscillating". Great foam for 3 seconds and pressure drop for the second. Then great foam for 3 seconds and down pressure again. Like a waive pattern. What is causing that?
What’s that Gun that connects to the cannon called?
I Want One SO bad
The active 2.0 and the Ve52 it’s recommended not to use the 1.1 mm office though from what I’ve read? It make the pressure washer surge since it’s not made for to be used with a 1.1
Homie still haven't responded. I want to try to his foam cannon but I'm afraid for the same reason u said
Great stuff
I was looking at the Ryobi pressure washer and it has 1.2 gpm rating. Will this foam cannon work with that insert ?
Bought your stubby gun and the swivel , huge difference !!
Very nice E46 👌
My dad just bought a 2023 Dacia Duster and he takes it off-roading sometimes but it gets dirty really quickly, any tips on what products I should start out with to clean the car?
I would deep clean and polish the paint up then ceramic coat it. It lasts about a year and all you need is to rinse off the car with water. When it starts to fade off in some spots, you can use a detailling spray that has ceramic in it to touch it up and make it like new! Id reccomend watching some videos from chemical guys channel. They go in depth of how to take care of your vehicle :)
@@MTB_CRZYI somehow ended up finding this. Thanks I tried and you’re right
For the form cannon, is that compatible to the most of electric pressure washer?
I have a 3200 psi 2.5 GPM Husqvarna (gas powered) pressure washer. Is this too powerful? Do gas washers work for detailing?
I’d like to try your swivel nozzle
Clean
It's the 1.1 mm orifice a smaller or bigger diameter than the orfice that's already inside of the foam Cannon thing? The orifice on the phone Cannon thing that I have looks like the hole is bigger than the 1.1 mm that I ordered on Amazon after watching this video.
@@darylcooper5481 thanks Daryl. Much appreciated
You aren't getting 2 gpm on most electric pressure washers, nor is it needed. For some reason obsessed garage got everyone to think that you need more water. It might save a little time, but only very little time, and your water usage will increase. As far as cleaning ability, it really isn't all that important to hunt down an especially high flow pressure washer, unless you're in a high volume detailing environment.
What’s a good pressure washer off of Amazon?
How can i make green color foam?
Will a 1.1mm orifice be ok if I have a pressure washer rated for 3100gpm and 2.3psi?
The smaller 1.1mm is really only for lower PSI and GPM washers, the typical 1.25 I see with others is usually good for yours but you can try the 1.1mm
3100 psi. 2.3 gpm you mean? 😅
Hey can you guys make a super high quality 1/2” quick connect like you do for the m22 adapters hard to find good quick connects made with quality stainless steel
That’s an interesting question, something to think about for sure
@@mckillans I would love to 1. Have better products in the market such as the ones you provide, 2. Support your business if you decide to start developing that or release that product make a video and I’ll be your 1st customer 😂
Do you use DI water?
Is higher psi better?
had no idea to add water to the soap. I just filled the whole thing with soap.
Hey my mckillans pressure washer gun gets stuck when I let go of the trigger and keeps spraying water anybody know a quick fix?
can you use a gas pressure washer?
Hell yeah! But only use around 1000 psi, you dont need much pressure to get good foam or to clean a car. Gas powered tend to be significantly more powerful than electric, be careful not to damage the relatively sensitive vehicle surfaces.
What's the best way to avoid water spots?
Shade, foam cannon, ph neutral soap, wash panel by panel from bucket. All of those work.
Avoid water
Work in sections and wash in the shade if possible
The foam cannon is to equally spread the soap.
Not true.
Think my 4.2k psi 4.5gpm will be powerfull enough? 😂
Who buys a foam cannon without a pressure washer? I've never seen anyone use a foam cannon without a pressure washer
Wtf is a gallon tell in litres
If you googled it you’d have the answer already
So bad advice , you risk a lot with foam cannons , sun , waterspots, buckets methode with pre spray ikfoam is fast , same result, hope you guys take note
All he Details are ///\/\ cars?😂
He was doing a different car too. I'm guessing that bmw's his
Rule #1; no one needs a foam canon.
You do.
Detailers who use foam cannons waste a ton of time
Not true whatsoever.
I can say alot of things are waste of time but not exactly this depends in some cases.
@@visioncorp5228 100 percent true everysoever
@@skullman0819 you make no sense. And have 0 evidence.
Not true detailers would rather have quality over quantity because the better the vehicle is cleaned the better the chances to gain potential customers through that customer would reference friends and family relatives to call and book car detailing appointments but for some who just wants to clean their car is up to them to use a foam cannon or not
Just go to a car wash.