This could not be demonstrated and explained any better than this man, absolutely amazing video. Thank you for taking the time to put this together and sharing with the PC Repair Tech community. Lovely and God bless you man.
hi man,merry xmas and new year in advance.thanks for all the videos and knowledge you share to us in youtube,keep up the good job through the next year and in good health.
Hey! Nice video. I have one Macbook Pro A1706 (touchbar) that i had dropped coffee on right side of topcase. Here in Brazil, two technicals said thats isn't recoverable. But seen this video and now i have hope, any of cases apparently is it worst that mine.
I'm loving your videos. Many thanks for sharing. Can I ask a couple of questions please? Did you just ultra sonic the part of the board you worked on and also do you have a video talking about the equipment you like to use? Thanks again and happy new year!
In cases of liquid damage we ultrasonic the entire board to ensure the entire board is cleaned. We discuss equipment we use in a lot of our videos, but we don't have a video dedicated to equipment discussion as of yet. Happy New Year!
I don't recall your name but thanks a lot for the reply to this and my other question on a different video. Yes I have started to watch more of your stuff and your'e right you do talk about your equipment more. Anyway thanks again and I'm sure I'll have more dumb questions in the future :)
my 13-inch late 2016 MacBook pro had liquid damage. The touch bar is completely off, I reformatted the machine, it is now stuck on a 'critical update' loop, I am assuming this is because an update that needs to be applied to the touch bar cannot be applied since the touch bar is off. Hardware diagnosis comes back with no issues found, I am also able to boot successfully in safe mode. What do you suspect is the issue, does the touch bar run on a separate circuit that could be fried, is this a part I can buy from you?
As you mentioned there are two USB C controllers, ones cap was damage and had 5v, not 20. and as owner said: it fails to boot, so what about another USB C controller voltage?
Powerbook Medic Thanks. So that’s why when i short circuiting usb, all usbs goes off. All usb powers wire are connected. And Big thanks goes to Texas Instruments for nice chip!
I spilled some water on my Macbook Pro two days ago. My computer wasn't completely shut down when it happened (on sleep mode). Next morning I plugged in power to turn on and it won't turn on. I'm wondering if cleaning the board will solve the problem? Or do you think I need to replace any parts?
It's impossible to say with a spill. Cleaning the board may help, but it really depends on where the liquid went and how long it sat there with current going through it. The sooner you get the board looked at, the better. If you can't find anywhere locally, you can send the unit to us at this link : www.powerbookmedic.com/repair-center/quote.php
Hi man ,any solution for a Touch bar issue,black no image,laptop start but no touch bar ,any solution?... is not work with SMC reset or other commands in terminal,hardware solution...thanks
Nick McRyan Typically, the top case needs to be replaced to fix any touch bar issues. Unless it’s been liquid damaged, then the logic board could be damaged too.
This could not be demonstrated and explained any better than this man, absolutely amazing video. Thank you for taking the time to put this together and sharing with the PC Repair Tech community. Lovely and God bless you man.
hi man,merry xmas and new year in advance.thanks for all the videos and knowledge you share to us in youtube,keep up the good job through the next year and in good health.
Thanks for watching and Happy New Year!
Hey! Nice video. I have one Macbook Pro A1706 (touchbar) that i had dropped coffee on right side of topcase. Here in Brazil, two technicals said thats isn't recoverable. But seen this video and now i have hope, any of cases apparently is it worst that mine.
I'm loving your videos. Many thanks for sharing. Can I ask a couple of questions please? Did you just ultra sonic the part of the board you worked on and also do you have a video talking about the equipment you like to use?
Thanks again and happy new year!
In cases of liquid damage we ultrasonic the entire board to ensure the entire board is cleaned. We discuss equipment we use in a lot of our videos, but we don't have a video dedicated to equipment discussion as of yet. Happy New Year!
I don't recall your name but thanks a lot for the reply to this and my other question on a different video. Yes I have started to watch more of your stuff and your'e right you do talk about your equipment more. Anyway thanks again and I'm sure I'll have more dumb questions in the future :)
my 13-inch late 2016 MacBook pro had liquid damage. The touch bar is completely off, I reformatted the machine, it is now stuck on a 'critical update' loop, I am assuming this is because an update that needs to be applied to the touch bar cannot be applied since the touch bar is off. Hardware diagnosis comes back with no issues found, I am also able to boot successfully in safe mode. What do you suspect is the issue, does the touch bar run on a separate circuit that could be fried, is this a part I can buy from you?
That could be due to the top case or the logic board. Usually that error loop means the system can't detect the touchbar.
How much would a service like this be
You can find more information on our logic board repair service including pricing at this link: www.powerbookmedic.com/xcart1/pages.php?pageid=67
As you mentioned there are two USB C controllers, ones cap was damage and had 5v, not 20. and as owner said: it fails to boot, so what about another USB C controller voltage?
They all have the same voltages.. it should be 20v
Powerbook Medic
Thanks.
So that’s why when i short circuiting usb, all usbs goes off. All usb powers wire are connected.
And Big thanks goes to Texas Instruments for nice chip!
I spilled some water on my Macbook Pro two days ago. My computer wasn't completely shut down when it happened (on sleep mode). Next morning I plugged in power to turn on and it won't turn on. I'm wondering if cleaning the board will solve the problem? Or do you think I need to replace any parts?
It's impossible to say with a spill. Cleaning the board may help, but it really depends on where the liquid went and how long it sat there with current going through it. The sooner you get the board looked at, the better. If you can't find anywhere locally, you can send the unit to us at this link : www.powerbookmedic.com/repair-center/quote.php
Yes, power goes through the unit even when it is in sleep mode.
@@PowerbookMedic I see. It was on sleep mode at least 12 hours since the spill. I sent in a quote on your website and hopefully it's fixable...
@@sunyoon They should get back to you quickly with the quote. Usually issues like this are fixable.
Hi man ,any solution for a Touch bar issue,black no image,laptop start but no touch bar ,any solution?... is not work with SMC reset or other commands in terminal,hardware solution...thanks
Nick McRyan Typically, the top case needs to be replaced to fix any touch bar issues. Unless it’s been liquid damaged, then the logic board could be damaged too.