Starter Replacement 2012-2018 Ford Focus 2.0L
Vložit
- čas přidán 7. 09. 2024
- In this video I go over the removal and installation procedure for a starter on a 2012-2018 Ford Focus 2.0L equipped with a DPS6 transmission.
As mentioned in the video the front end of the vehicle will have to be jacked up in order to gain access to the starter. The vehicle will have to be jacked up and properly supported. Instructions on how to do this properly were not given in this video. You will have to reference your repair manual for this information.
Warning ⚠️: Improperly lifting and supporting your vehicle can result in serious personal injury or death. You must reference a reputable repair manual for information on how to do this properly.
For tool reviews and product recommendations by Barbour's Auto Help visit my store front on Amazon by clicking the link: www.amazon.com...
Discloser: As an Amazon affiliate I make a commission on qualifying sales.
DISCLAIMER
Barbour's Auto Help is not responsible for any damage or personal injury incurred in the process of performing any auto repairs done by you the viewer. Automotive repair is extremely dangerous. Repair your vehicle at your own risk. It is the viewers responsibility to verify all information and procedures as outlined in YOUR REPAIR MANUAL AND OWNERS MANUAL FOR YOUR VEHICLE. Owning and using a repair manual suited for your vehicle is essential for correctly and safely performing ANY repair to your vehicle. Always wear safety glasses and heed all instructions for use applicable to any piece of equipment you may use. Due to circumstances out of the control of Barbour's Auto Help, Barbour's Auto Help makes no guarantee that by the use of the information given in this video a quality repair will be made. Also, Barbour's Auto Help makes no guarantee that the information provided is totally complete, synchronized and accurate. Verify everything using an appropriate repair manual.
Repair your vehicle at your own risk! Barbour's auto help does not guarantee a proper repair using these techniques. Further more I do not guarantee you will not damage your vehicle in the process of repairing it.
Thanks allot for this, with the engine out of the car it was much easier to see how to perform the procedure 👍
Thank you very much for this video, it was very useful for me ! I am A.C. from Romania and had a 2015 yr. Ford Focus 2.0L from US.
Glad it helped
What the hell . Do it in the car. We driveway mechanics can't do it with the motor out
You are a champion
The two ends hat rubber insulating strip protrude a bit from the cavity. How is it supposed to sit against the starter when you reinstall it? Seems like it gets in the way.
It may have come into contact with oil or fluid causing it to swell a bit. I usually trim it flush with the bell housing if this happens. However if it's only protruding a millimeter or two I don't ever worry about it.
Thanks 👍🏾
Great vid good job
Had to replace it in a year and a half again . Had oil on pinion gear . Trying to find actual oil leak . This mechanic said it's definitely from real seal . Also have valve cover oil leak which might be causing this . In your opinion , can top leak get into starter gear ? Or is it pretty tightly sealed against from the outside ? And this other mech said it was rear main seal .. yeah will still get another opinion and even try to find it after I clean it a bit .
What year is your Focus. A lot of the early years are notorious for leaking transmission input shaft seals. This could possible be a cause too. Valve cover leaks can diffidently get in there. Rear main seals as well as oil pans are known sources of oil leaks in this area. Not uncommon to have more than one leak.
VERY GOOD THANKS WAS HELPFULL
Glad it helped
Same Ford Focus C-Max 1.8 DM2
Thank you.
Now the starter didn't work but once I removed it i and this other mechanic bench tested it and looked good soo I don't know what's going on ? Maybe under load trying to crank flywheel will fail ? Just bizaare . He said try it put it back on there and see what it does . check clean alll connections including battery .. Battery is about a month old . Also when I removed starter no cable / wire was attached to bracket that I remember so I guess it's there just loose ..
Are you getting power to the starter. Have you tested the circuits with a volt meter or a test light?
@@BarboursAutoHelp no I haven’t tested those yet and I suppose that could be it. This mechanic is older in his sixties soo he’s pretty experienced. He’s fixed other problems very easily and quickly within minutes. I’ll do as he says check clean all connections as best I can. As to cables besides looking at the ends for wear and damage what else do you recommend? Testing it at starter connections with volt meter?
I have a 2015 Ford Fiesta, question is...can the starter be removed without taking off the intake manifold?
Absolutely. I do it all the time. Don't have a video on it though.
This doesnt look like my 2016 ford focus at all. Very confused
Is it a 2.0L?