How to Adjust 2T OIL FLOW perfectly in Autolube pump || Detailed Process
Vložit
- čas přidán 15. 05. 2020
- Complete Process to adjust the oil flow in you yamaha RX series motorcycle.
Worried about 2T OIL FLOW ADJUSTEMENT IN YOUR YAMAHA RX SERIES BIKES
Here is the Complete guide, Do it well once and You'll never need to redo it. #2TOilPump
In this video i have shown the complete process of adjusting and caliberating the Pump
----------Whats #MinimumStroke and how to adjust it------------------
--------------How to #AirBleed the pump---------------------------------
-----------------------How to set he correct #OilFlow -------------------
All these three process is described in the video, watch it with patience, understand it and then only attempt it.
****************TECHNICAL DETAILS ************
-- AUTOLUBE PUMP that comes in yamaha rx100,rx135, RXG,RXZ
-Minimum stroke 0.20mm - 0.25mm (need to measures while the pump is fitted and the Clearance is maximum.
--On safer side you can keep the clearance to 0.30mm
--Any how it should not be more than 0.35
--Additional shims might be needed for proper gap
All these three process is described in the video, watch it with patience, understand it and then only attempt it.
***** Other series related to the 2T OIL PUMPS IS HERE ---
1) OILSEAL REPLACEMENT GUIDE - • How to change oilseal ...
2) CLEANING SETTING- • Yamaha Rx100/135 Auto...
REST ALL IS BELOW-
you can watch my videos from the link below :
MY YEZDI :-
1--- • YEZDI 1978 RESTORATION...
2) • YEZDI 250 RESTORED | A...
3) • Yezdi diaries,Forever ...
3) • YEZDI 250 EXHAUST SOUN...
Royal Enfield-
1) • Enfield 350+ FZ16!BROT...
2) • OLD MODEL BULLET 350,O...
3) • OLD BULLET 350 ON HIL... Link to my rajasthan Ride series
• Rajasthan Series
-----------------------
Link to TECHNICAL playlist 👍
• DIY/Motorcycle Works/ ...
----------------_---------------
Link to Yamaha Rx series bikes -🎂
• Yamaha Rx maintenance ...
Rides -
• MOTORCYCLE RIDES
FOLLOW ME ON INSTAGRAM - moto_travelxd
MAIL ME AT - abhifor102@gmail.com - Auta a dopravní prostředky
Hindi version wala video ka link -
czcams.com/video/Xn-7NwpyCws/video.html
Nicely detailed explanation,a small tip to make it easier to remove the shims is to remove oil pump by just removing the 2 retaining screws,no need to remove oil pipes. Keep up the good work.
Very detailed description of the procedure. Thank you so very much!
This is the most detailed video of the Oil Pump settings. Good one ! 👍
Glad it was helpful!
Awesome thank you so much for doing it in English as some of the other channels is not, and so detailed wow you rock man well done from
S A your knowledge is greatly appreciated 👌👍
Thank you very much for the time you have taken to put this detailed video together!!
I have just rebuilt my Yamaha DT175 pum but was unsure how to set it correctly.
Take care and thanks again from Australia 🙏
Glad it helped
Thanks! I got the main idea of how to adjust mt Yamaha chappy lb50 oil pump after refurnishing
Corfu - Greece
This is the best video for oil pump service! thanks
Very informative and helpful step by step guide (thank you). Any advise on a two cylinders and twin carbs bike?
It was very helpful. I will not try to do my self buy i will tell my rx mechanic to do this and observe him properly, thankyou for making this vedio😊😊
Loved your honesty 👍
Thank you .
Excellent video! Helped me in California with 1974 DT 125. Also watched the Hindi language version.
Happy to hear back from a DT owner, legendary bike .have few countable numbers in India .
thanks to this video i had fix my DT125 2t pump!
happy to hear that... most welcome sir
Thank you so much for this very informative video you made.
You're welcome brother..Thankyou for being here♥️
Bro. You are such a beautiful explainer
Excellent video! Learned a lot!
Any tips if the oil doesn't come out of the hose to the carb? I've done the first three steps. Thanks.
Nice content and very precise tutorial. Good job.
Glad it helped
Awesome video 👌 quite informative
Awesome explanation, thank you
Brother good video ❤what is the minimum and maximum amount of 2 t oil in ml per litre can adjust in oil pump how much if we set in minimum and how much if we set in maximum in ml/litre
That was very helpful. Thanks!
Glad it was helpful!
Thank you
From south africa.
Most welcome Lucas... Glad to know it was helpful. Love from India♥️
Thanks a lot brooo
Very nicely explained..this is what biking culture should be about to educate each other 👍🏻 KUDOS TO U BRO
Thank you brother,you're absolutely right.
excellent!
excellent dude thanx lot
Very nyc bhai
Detailed explain
Great job ..👍
Thankyou bhai
Description is very valuable
Very helpful👍
Very Good explaination
Very useful thankyou somuch. By yamaha two stock lovers
Thank you.
thank you sir.
thanks for sharing...
Hi bro your videos are informative plz make a video on reed valve difference in yamaha rxg, rx135 & rx 100
thank you , Defntly i will try.
Great job dear friend very knowledgeable video.... But I think so lots of Yamaha rx100 people don't know about the oil pump adjusting... Those know from your video.... Thanks again for this..... Keep it up dear... 😊😊😊
Many people discard this pump..but if these pumps are kept working nothing will happen to the engine...
Thank for appreciating the work ,happy to help 💐
Excellent video, got it nice
Thank you sir
Thanks👍👍👍
Brilliant. Is higher pump stroke bad?
Nice video bro
Thanks bro
Welcome brother..
Thanks Bro
Welcome
Good video. And change the playback speed to 0.75x, it become perfect.
Super👌
Thank you! Cheers!
Very informative video. 👍 can u make a video on the differences in rx 100 and 135 4s/5s oil pump? And if it's ok to use a 100 pump in 135 and vice versa?
Guy starts the bike to bleed oil pump so what's already mixing with fuel? Daft as fuck 👍👍
nice video sir 👍👌
Thankyou sir. 🙂
hello, first of all, thanks for your informative video, I have the rx115 even though I don't understand it. If there was a Turkish version, a lot of people would benefit and it would be great for me.
Hi.. if any queries you've regarding this you can dm me on instagram anytime..
I
Bro ❣️
Thank you bro... ♥️
Kerala Yamaha riders
make a tutorial about carburator tuning of rx100
Super
Thanks
Hi great video thanks. Just one question, if removing shims to reduce the stroke would then this also reduce the lower limit setting ? My stroke is also to long around 2mm on a bran new oil pump. Thanks again
Minimum stroke doesn't get affected.. keep it as it is, it's pricol pump..
Later on if you feel then reduce the stroke.
hi, I have a mx100 --- where should the cable from the pump ; be connected?.
Thanks a lot! Very detailed explanation. Will do it on my DT 175 from 1979. Just one question. Will it be no problem when disconnecting the oil tube for bleeding from the carburetor while the motor is running on idle? I mean during that time the machine will get no fresh oil.
Thank you for you words,happy to hear from you.
There won't be any problem. Easily you can bleed it , hardly take a minute or two. Go ahead, DTs and Rx are rugged bikes . 🍻
Thank you so much for quick reply. I will do so. Take care!
Excellent. Thank you buddy. All your videos on RX series were superb. I want to know if there is any difference in cylinder port dimensions between RX 135 4 and 5 speeds. My lathewala tells no difference, only the serial numbers are different and even the heads are of same sizes despite having different spare part numbers. He says the difference in sprocketing and gear ratios of 5-speed makes it extract 2 bhp more and give about 10% increase in top speed. I want to know your thoughts on this. TIA.
ports are very much different different.
Bhp is generated and calculated at engine / primary never at final drive ( sprockets )
In details video will be coming up.
Thank you for the reply. Awaiting the video.
Most welcome, thankyou for understanding and appreciating the work.✌️
No oil coming out of second pipe that connects to carburettor on my DT125LC bike ?
Hi I've got a peugeot speedfight 2 liquid cooled 2stroke engine the engine starts up but is filling up with sludge in the crank case iknow the waterpump if broken can cause sludge build up but could it also be the oil pump as well any help to remove the sludge from the crank case would be much appreciated
Hey. i"m not aware of the technicalities of the engine you are talking about. AFAIK , any kind of sludge built in the crank case can be primarily cleaned by the "engine Flush" solvents available in market.. this process can be repeated 1,2 times for best result. make sure the source of sludge is diagnosed and repaired,or else post cleaning also you may find sludges... hope this helps
Engine bearing sound or connecting rod bearing sound?
Very helpful same procedure for rd350 also right let me know 😊
Absolutely same for rd.
Keep the minimum stroke to 0.25mm (at ideling)
Oftenly am getting leakage in the side of 2T pump case side, what can I need to do to stop this?
135rx I have excuses smoke flow even after adjusting the cable till end
This step-by-step video is very informative but I have a question, is it the same for Rx 135, or is it different for it?
Its is almost same for both.. what we keep at safer side for rx100 is the correct range for rx135
@@MotoTravelRide Thanks
I checked my 2t oil pump its leaking a lot
what do I do with my pump?
@@anirudham4430 u need to change the gasket of t2 oil pump
Hello sir recently I have installed new pricol oil pump in my Rx100 we have to adjust the settings or we can use directly
Hello...
You'll leave to check the setting atleast, if it is OK then no need to adjust.
👍👍👍👍👍👍😍😍😍
I have a doubt, please. Can you share if turning the big long oil pump adjuster nut on the cable anti-clockwise increases or decreases oil flow? Since you've mentioned in the video oil flow can be adjusted from the cable itself, wanted to know which turning it which direction increases and decreases oil flow. Thank you.
Hey... Probably , I had missed to mention that in the video.
Turning it anticlock wise increases the flow .
@@MotoTravelRide Thank you so much for your quick reply. Yes that was the crucial point on the video that was missed, but nevertheless excellent as always!
Thanks a lot 👍
After doing this stuff m facing the leakage changed oil seals also any suggestions on this please
Check the leakage point is it from inside the pump main body or from the gasket (where we connect the pump to the casing). Then rectify accordingly.
Dm me on Instagram, can help you better.
It is better to use transparent t2 oil pipe for carburetor because oil flow in can be seen properly
Correct... it makes things convenient
I need help
Bro on top to control the oil flow in 2t pump side, on which thread we want to put the screw and tight on a standard scale for rx 100
Bro There is no standard scale for oil flow, from top adjustment .
Check these to understand of oil flow os correct or not---
There should be little smoke coming frm exhaust
spark plug should have excess oil
Thanks broo
@@MotoTravelRide plug should have excess oil? Also how you premixed the petrol before you started it to bleed the pump there's a few big No No's here also should of stated more oil the more your running lean not rich like everyone seems to think but of course be we need oil brilliant video though
Bro i am confused how to adjust the height of adjuster and how to lock it
Nice beard bro
Thanks bro..
Please let me know in normal course how many KM run in 01 Lt. of 2T oil of RX100
I also have the same query
Broo wheather minimum stroke for pump is required when the bike is in idling
stroke is always set at ideling , it always remains same throughout every rpm range.
Bro im facing a problem in my rx135 the engine get off after pushing it hard after 100 not getting higher rpm i mean after opening more than 50 accselator it starts missing like pattt patt not reaching to higher rpm
It can be anything.. pls msg me on Instagram to discuss details.
Bhai petrol pura nai mil rha ,,,,oil filter saaf kro ,,or carburettor ko bhi saaf kro ,,air fuel mixture set kro ,,,,,,,,meri bike me bhi same problem thi ,,,,,,oil filter me kachra tha , ,80 k baad pht pht kr ri thi
Hi team, my Rx135 makes fluttering beat ( silencer beat) under constant speed, if acceleration is increased silencer beat becomes normal
I have changed carbeurator main and pilot jet, checked all the coils, changed ignition coil
But problem still exists
Pls suggest a solution
this indicates the bike is having incorrect fuel adjustment( tuning) or inappropriate jet size ( main jet most probably)
सर Achcha पिकप के लीये kya kya kya karna padega Mere RX 100 कोG1 block hai original 25 का है जितनि पिकप लेना छाईये ऊतना लेनहि रहि तो आप बतासकते है
Agar gadi ka engine strong hai to fir bas apni CDI aur carburetor ki tuning ko check krwaye. Picup jarur legi
Sir original oil seal kaha milega
Is there any difference in rx135 4 speed and rx 100 and rx 135 5 speed oil pump
No they are same...only few 5 s models have smaller oil pump from pricol.which is a totally different looking design.
All have functionality same.
@@MotoTravelRide thank you for your reply
Excellent, mais pourquoi les commentaires ne sont pas en français...??
Video is from an Indian. That's y comments are mostly in hindi or English
Yesterday i bought a 2k rx135 for 7000
rx135 2002 model
5 speed manet difrence or same
reply please
No sure , but AFAIK they were little different .
My Rx 135 full reces without opening the throttle....this may be oil pump is not in working condition?
Check the cable that's fitted on the pump..sometimes that gets stucked .. duplicate cable, freeplay check
Oil flow kaisa kam kare
Casing adjuster se
Bhai one problem I am facing, after aligning the dot with pulley, you said to give false kicks and gap will apear but in my case the gap is not coming
Shouldn't be like that.. you can start the bike and observe the gap as well.. if it appears, then its good. Then all you need to do it keep kicking to reach gap position and make your adjustments accordingly. .
@@MotoTravelRide okay
RX100 or RX135 🤔🤔🤨
Sir air bubls nikal ne k bad gari jada smock deti hai kay..rxg hai pls help Sir meri gari jada smock de rahi hai..2t oil cable r perfect pls help sir
2 stroke to smoke degi hi.. air bubble nikal dene ke bad oil supply Acche se hota hai.. isly smoke badh jata hai. Thik hojaega apne se wo.
MotoTravel .. Sir kitne din k andar kom hogi smock ..SIR REPLY PLESE
@@miltondey295 5-10-15 kms me smoke km hojaega, agar nahi hua to adjuster se oil flow ko km krna hoga(video ke last part me hai adjuster ka kaam)
MotoTravel Tnx Sir
hello sir i have one small doubt , in 1 litre of 2t oil filled in the side tank how many kilometers can we ride
900-1000kms
Thank you 😊
Yamaha Rx100 ka oil pump leak kar raha hai. Seal bhi change ki hai. Exilator wire ke aage leak kar raha hai. Jaha par three wasar hai wahi se leak kar raha hai. Koi upaay batao sir
पंप प्लंजर ख़राब है। नई पंप लगवाना होगा अब।।
Kick marne pe 2t pump ka gap nhi badh raha hai help!
Fully start kr ke dekho bhai ek bar....
@@MotoTravelRide plug sab laga ke kya
hindi language me ak video . plz hindi
Ayega kuch time me.
Lifeline for 2 strokee riders
I just fixed my 2t pump after failing to work and my mechanic requested i change it. I feel cheated.
Hindi
1-2 din me hindi wala aajaega 👌
czcams.com/video/Xn-7NwpyCws/video.html
Sir hindi me banao video pls sir👍
🙂 Okay
Sir meri rx 135 ka pump apke pump jaise he kam kr raha hai, kya mere ko petrol tank me bhi 2t oil dalne ki jarurat hai sir?? Pls reply sir
@@kawatrasahil1890 agar pump kam kr rha hai, oil aarha hai exit pipe me. To tank me dalne ki koi jrurt nhi h.
Thanku so much sir👍👍
Sir Wich 2t oil is better for Yamaha rx 135?
Tiluge too much
Bro i hav some serious doubt on my rx 135 not getting maximum speed stop on 90 . Pls help, can i get your number pls ?
Instagram pe contact krlo bro
Mera bike ka tooti pump ki pipe pe baar baar bulbuli ho raha hai kyu sir ?
Oil pura bhara hona chaiye box me, bulbuli shuruat me niklega fir pura oil ayega.no bulbuli
Ye hindi wala video hai .
czcams.com/video/Xn-7NwpyCws/video.html