how to install a loc - line output converter in 3 minutes
Vložit
- čas přidán 3. 06. 2021
- LETS MAKE THIS EASY
learn how to install a loc or line output converter.
This is a car audio how to tutorial that will explain what a line output converter is and what a loc does. a loc is a device that converts your high level input from the factory audio system and provides a low level output so we can run rca's to our aftermarket amplifiers. in this video I use a 1 channel line output converter and tap into the factory sub wires to get signal for our sub amp.
SUBSCRIBE FOR MORE CAR AUDIO DIY TUTORIALS radio removals, radio installs, speaker replacement, speaker installs, car audio reviews and much more.
🔻
Introduction To Car Audio: Car Stereo Help E-Book www.jpsaudio.com/ebooks-courses
Parts used in the install
Electrical Tape www.jpsaudio.com/product-page...
Red Butt Connectors www.jpsaudio.com/product-page...
Zip Ties www.jpsaudio.com/product-page...
Line output converter www.jpsaudio.com/product-page...
Speaker Polarity Tester/ Tone Generator www.jpsaudio.com/product-page...
🔻
Did this video help you? Want to support the Channel? Join me on Patreon and get exclusive content and GIVEAWAYS
www.patreon.com/bePatron?u=43...
🔻
WHAT TO WATCH NEXT:
WHICH WIRE HARNESS SHOULD YOU BUY FOR YOUR CAR: • which car stereo wire ...
HOW TO SAFELY TAP INTO YOUR CAR FUSEBOX: • HOW TO SAFELY TAP INTO...
HOW TO WIRE A RADIO: • Car stereo wiring harn...
HOW TO STRIP A WIRE • How to strip your wires
HOW TO PLAYIST: • how to
🔻
Samsung Glaxay 10e amzn.to/2SiKVKI
~Check out my first channel if you love BASS~ / jpsaudio08
🔻
~Tools I Use almost everyday~
NEW Milwaukee right angle driver amzn.to/2t4mDvM
NEW Milwaukee right angle drill amzn.to/2GwZAwQ
Install bay panel removal tools: amzn.to/2Jv4XiP
Install bay Speaker tester amzn.to/2LHOYki
Digital Multimeter: amzn.to/2Hcz111
Milwaukee drills: amzn.to/2Lxvu1y - Auta a dopravní prostředky
Love the way you tapped into the speaker outputs. Most people just cut and strip and I don't like cutting stock wires. The way you just stripped it and tapped into it was great. Good Job!
Simple and to the point! That's how you make a video. No reason for this to be 20 mins long.
You literally just saved me over $1000 with just one video I’ve been searching all over the place for this video and finally found it
Had to sub. Man that was fast clear and to the point. Salute homie
Probably the most informational LOC video explanation I’ve seen. Thank you!
So straight up and correct. Best video bro
Appreciate the upload brother. Going to install my sub in my bronco tomorrow thanks to this vid
Duuuudddeee I think you just helped me solve a question I've been working on for the last year and a half!
Dude, thank you thank you. Your 3min just cleared up days of questions for me. Using a LOC to tap into a powered sub from a home theater setup. Relaying the low level signal to a mini amp that powers two buttkickers. Your video made sure I didn’t blow anything down the line so really appreciate it 🙌🏻
That's awesome glad I could help
V
Same as everyone else. Thank you for being clear
Thanks man your video was super helpful and to the point 10/10
Thank you for explaining if the car already has sub lines. you're the best. twisting them together! car has sub lines and ACC line, and battery in the trunk... my install couldn't be much easier.
Great vid nice to have someone who can actually explain things!
Luv your channel JP,,,Subscribed 😎👍
JP, buddy you are sooo top notch man. I'm a trained sound/studio engineer and been a backyard mechanic since 14 and tinkering with car audio off and on, since when subs first came out, 57 years old now. Things have changed since the days of radio and cassette players with 2 knobs lol. I stay current though doing installs today. When I need to double check something/reference something new, you are there! So just want to thank you Brother for your vids, the best!
Lol have you lived through 8-track players to today's gear too? Nutz!
We in this together bro. Glad I can be if service
I have a question
That’s very informative in 2 minutes, THANQ
Watched many videos this is the first that I truly understand
3 minutes when other videos are 20 minutes plus. Simple and plain instructions. Thank you
Short sweet and to the point bruh. Thank you!
💯💯
This literally answered all my question in a short concise video. Thank you brotha
BOOM...LOL Glad it helped!
HEY I HAVE A QUESTION, SO I GOT EVERYTHING HOOKED UP, IT WORKS BUT THERES ACTUAL AUDIO, I THOUGHT SUBS WERE JUST FOR BASS? THERES MUSIC NOISE COMING FROM IT BARLEY ANY BASS
@@sleepingmoon6649 switch your settings on your amp if it has low pass / high pass settings switch, switch it to LP (LP) provides more bass (HP) more vocals
@@jptheinstallguy could you help me understand for my 2019 Nissan Maxima?
Well done. Easy to follow. Thank you.
Anytime💯
Thank you bro, provided info prior to my installation!
Extremely helpful!
Straight to the point! Love it
🙌🏽🙌🏽💯💯
You on deez?
Thais is what I needed! 🤛🤝
What perfect example video Fr ✊🏽💯
great video. thank you brother
Best video on the subject thank you.
Thank you just what I need
SOLID!! Thank You!!!
Great video
Very clean thanks bro
I want to say...
It is vastly comforting to notice someone call car speaker mid-range woofers. While generally and usually true, some speaker set ups include tweaters.
I get annoyed when i am conversating someone over audio stuff, and i point at the speaker in the driver door, aa an example, and remark something about that woofer, only to be cut off by a response like, "thats jot my subwoofer, thats my speaker" like i am the ignorant one.
Its happened more than i wish.
So, yes, thank you for referring to them correctly!
Great video.
Great video man!
Appreciate it!
perfect video man
That was the best explanation of my question about about hooking up to factory sub. Thank you sir. Love the calm explanation.
Glad this was able to help you out🤜🏾🤛🏾💯💯
Perfect video
Exactly what I needed thank you bro
💯💯
Best video:) short and now i know how do it right and easy.
Thnks :)
Glad it helped!
Wowwwwww literally the best explained straight up video I found. Holy fuck. I spend hours trying to find something like this
Like it's awesome step
Bro i almost cried putting my sub in my car. My other car had an aftermarket head unit and was a 2002 so i didnt need a LOC, now my cars a 2012 civic si with the factory sub, tried tapping into it once, the amp wouldnt even turn on, i was over it. Couple hours later I rewatched this, made sure i crimped everything tightly and properly, spent 30 minites and now everything works😭😂
My guy ........... all I needed to know. Quick, and accurate. 👊
🤜🏾🤛🏾💯💯
That’s why your dog got ran over kid
Good video man thanks, indepth...
Thank you 🙏🏾🙏🏾
Good stuff
Clean install
In addition to running speaker wires from the LOC to the car speaker wires, I just realized I ran an additional set on both car speakers and ran them into the speaker terminals on the sub amplifier obviously where the sub speaker wires go into. The sub works and sounds great I just don’t know if there’s any issues to having another set of wires on each side of the car speakers running into the speaker terminals on the sub amplifier
Hey man love ur videos.. u give good details and easy understanding. My ? For u though is I have a Chrysler 200s 2015 and am want to put a chinese aftermarket stereo into it but cant find any info on what type of harness or module should i get to keep all my features? I know they got they the maestro ads-mrr interface but my headunit isnt compatible and all the ones that are is so expensive. Please help me out thank u
You're good bro.
great video.
🙌🏽🙌🏽💯
Short and concise , great. Thank you for your help. Question I want to run a amplifier to power by 6x9s. I'm going to assume it's the same setup with the loc you have connected here ( taking the signal from the full range speaker ) . Or should I take from somewhere else... Any help is appreciated
Full range speaker. Do not take from subwoofer roe your signal will be wrong.
Beautiful
Thank u damn u saved me a lot of time
One question tho is I got everything hooked up but my car is not holding voltage how do I keep it from going low on me
Hooking up the loc does it do anything to the impedance the head unit sees ? I mean if you have a stock 4 ohm speaker and your radio is seeing a 4 ohm load, when you add the loc is the radio still seeing a four ohm load with the loc wired to that channel also ?
Coz I'm using the door speakers do I have to make sure I use a driver side one and a passenger side speaker cheers
Can you connect a single speaker signal to both L/R high-level inputs on the converter or a powered sub with high-level inputs?
your video has seemed to make more sense than anyone else lol. quick question if you don’t mind though…. with using this system; does that mean that there is no need to run a radio wire from the amp to the back of the radio/head unit? the only other car i’ve wired was a 90’s model so a bit older
Hey I always watch your video..can you please help me with my 2016 audi s3..I want to know how to connect the wires from the sub to the lc2i
What’s the positive and negative on a 2017 acura tlx stock subwoofer?!
so quick question. I have a 19 camry without a factory sub. I have front and rear positive and negative for both sides. do i connect the converter to the front or rear speakers on the factory harness?
Great tutorial 👌 all other loc videos on CZcams should be deleted and this video put in their place. Thank you.
So with the 2-Ohm dual Subwoofer I wire the negative and positive together for the left and do the same for the right?
I just got a 2011 avalon stock sub sounds blown out can I use the same method you did but disconnect the stock sub
Is it better to connect to rear speakers or factory sub. Have a 2018 civic coupe with factory sub so seeing what would be the best to connect
If you have dual sub, the two whites go to the positive on first coil and grey's go to the negative on the second?
I hope i get a response 🙏. If i have a single voice coil sub and have coupled both L+R positive and L+R negative together then do I connect it to my front left speaker of my stock radio harness or my right speaker? Does it matter? Or is it still safe to split the connections to the left front speaker and right front speaker? I have a 2009 4runner.
do you hav a wire diagram for a 2012 chevy equinox with premium pioneer system? I plan to tie into my factory sub with the line out converter
Can I get the signal from one speaker or do I have to use both? Meaning if I’d pair the 2 + from the loc and the 2 - from the loc to the negative and a positive on one speaker it would be okay for a svc set up?
But will this work for a mini Cooper r60 I need help with the line converter install I got the power ran and ground ran just struggling with the Harmon kardon wire splice.
I have a factory sub that's dvc with 2 sets of positive and negative wires does it matter which ones I hook up to left and right??
Hey man I Installed one to what I assume where the rear speaker wires on the back of the HU and for some reason it don’t play no audio. I’m pretty positive I have the right diagram for the speakers wires but I guess I could be wrong
I have the Metra converter do I need to use the yellow power wire and black ground wire for the converter to work
Will having a factory amp effect this at all? I’ve got a 2013 expedition limited with factory sub and the amp is right next to it
Quick question so if I'm running a 4 channel amplifier and a subwoofer amplifier get a male to female connector and two male two female connector for the 4 channel for the left side and one male to female connector for the right side for the subwoofer amplifier?
Would this work with a sub amp combo like a kicker hideaway to a head unit?
Great video! I have a 2018 Silverado crew cab, what speakers should I tap off of? I bought an lc6i and I’ve heard that the front speakers get a full range signal vs the rears. What do you recommend?
Did you figure it out i got the same truck tryna see how tf to do it😂
I was wondering, could tap into the speaker line or factory sub line at the solder points of the speaker or do I have to wire it before it reaches the speaker? Is there a difference?
Also, since I don't have a factory sub but have to tap into the 6x9's in the rear, does that mean I still have to wire to two channels toghter? I am running a mono amp to my subs at 2ohms.
One more question. And I notice when I try to take a reading from my lineout converter, I see fluctuation and not a steady reading, what could that mean? And my RCA's check out fine after check continuity.
Thanks
Thanks!
thanks a lot for your support
Do I tap into the right and left side of the speakers? im hook into the front left speaker at the moment
If my car has two factory subs then can I tap one of them or do i have to tap both of them?
Hi. I have question. Can I install this kind adapter for active subwoofer alpine SWE-815?
Yo bro can I hook my sub up to a factory speaker wire or do I need to go behind the deck and hook it to the sub connection in the deck. Pls let me know. I don’t have an existing sub
So if I do this do I still have to splice the radio for installing subs?
Is that a good choice to ground all accord 2008-2012 or does it change with every car different ground ?
When you tapped into the speakers did you tap into left side only or both
Could I install loc to the head unit? Using the left and right rear speaker wires on the harness? Will splicing into it work?
only if you dont have a factory amp. if you have a oem amp then the radio only is sending signal to the amp and that wont work. if you have a base model where the radio is powering speakers then yes go for it.
Please some reply fast I need help I have a 1500 watt amp in 2 subs in 4 rear door speakers in 3 dashboard speakers in 2 corner speakers what do I need to connect everything in out it together I have a factory radio will this little piece right here power all my speakers or do I need something else I have a chysler 2010 touring
any chance you could tell me how to tap a line converter to a 2014 mb e350 factory amp?
do you have a video showing how to wire a line out converter into the speaker wires of a vehicle
What’s the best way to identify which wires are for left negative left positive etc
Solid
Hey man thanks for this video! So I have a 21 Lexus IS350 with a factory amp and head unit. I already upgraded all the speakers and upgraded the subwoofer which is placed in the factory location. The subwoofer is underpowered just a little bit. When I wire up the LOC I was going to twist the two positives and two negatives together and use a butt connector to attach to corresponding + and - on the pre-amp subwoofer wires then run remote to the amp and power to the amp from battery and ground to chassis. Do I then need to only connect the RCAs from the LOC to the amp to make the subwoofer be powered from the mono amp I am installing? Or do I need to also run speaker wire from the amp to something? And if so to where? All speakers are already upgraded and work fine with the factory amp, it's just the aftermarket subwoofer that doesnt get enough power from the factory amp. Thanks!
If I installed the LOC thru my factory sub, where should I put my sub volume level from my factory radio? Normally I put I set my volume level half way only.. any suggestion.
Thanks bro
anytime
Yes sir that you so much
Can you add additional speakers using a loc too?
Might be a dumb question but I have a 2013 dodge Durango so I would be running all the wires to the door speakers… so my question could I hook this up in the back of the radio?
Yo great video worked great till I unplugged my sub to work on it and plugged it back in I realized my amp was only powering the rear speakers instead of the sub, could it be because I’m using a mono block amp? Not gonna lie tho the amp made my stock back speakers sound impressive, 2016 Honda Civic so you know the speakers are 👎🏽
Is it okay to run these to the trunk speakers in 2013 Dodge Challenger
Trying to wire one into a 2019 CLS. Any diagrams or help??