Givi V56 brake light installation E160 installation guide - 2019 Yamaha MT-07
Vložit
- čas přidán 7. 09. 2024
- This is a rough guide on how to install the E160 brake light kit on a Givi V56 top case. Even though this is on a 2019 Yamaha MT-07 I'm sure other motorcycles will be similar. Keep in mind I’m not a professional mechanic, so I kinda fumbled my way through this. I’m sure I got some terminology and techniques wrong which might get corrected in the comments. Listen to them because I’m guessing they know more than I do.
Hopefully this video will give you a better idea on how to complete the task and what you need to do to prepare. If you have any questions please let me know and I’ll do my best to answer them. Take care!
Also, I know I need to get some brass drifts lol
Fair play to you doing the installation there and then, a guy just reading the instructions and doing it bit by bit, looks fantastic, think of the safety aspect, more brake lights and bright ones at that too, can’t be a bad thing.
To your closing comments, doing the job a second time would not take half as long. I once had to install ceiling fans, first one an hour, second 20 minutes, and and third 15 minutes.
Thank for showing me the process. definitely worth adding them.
Thanks for posting. I am actually looking to add this to my V56 case on my GS.
Thank you for this video. If you install any of the other accessories on your 56 Givi trunk, like the luggage rack or back-rest, please let us know how the install goes and maybe make a video. Thank you again.
A bit late maybe, but I would try to use the old punched out cover, turn it upside down and glue/silicone it back over the hole from the inside of the topbox thet hasn't the brakelights. I think that would make it water tight even if you take the box off the bike.
Thank you for posting - nice vid!
As nice as being seen with more lights is i can only expect with these pin touch conections that something will eventually fail and the brake light will stip working.
Thank you very much i couldn't understand the instructions 😀
Crazy such an expensive case dosnt have that 2 usd led allready fittet -
Good job! I enjoyed the video.
Good video It helped me decide to get one for my case
Very nice, thank you...
Thanks for your hard work.
Great video
Great video and very helpful 👍
buongiorno ho montato su bauletto givi v56 e ci sono riuscito pero ho notato quando freno si accende insieme faro posteriore per il problema che quando accendo i fari anteriore non si accende sul bauletto ma faro stop si dove ho sbagliato il mio scooter kimco xciting 300r 2011 aiutami a risolvere grazie !!!
Bonjour, et merci pour vos vidéos. C’est seulement des feux stop ou il y a aussi les feux de route ? Merci
Great video👍 I don't have the monokey rear plate. I have the Suzuki rack with the monokey junction kit. What size is the whole in the rear plate? In mm would be great so I know what size whole to drill out. Thanks PCG.
Cool !
Is it brake light only? Or does it give turn signals too?
Brake light only unfortunately.
I've located my power and brake wire, spliced in but no power to box. Any suggestions?
I would look to see where you have good power from the brake lighting circuit then work my way backwards with a circuit tester until I found the problem. I'd also verify that you're on the brake lighting circuit and the ignition is on.
@@croutonsinasalad5493 thank u!
What does that break light kit called? And where did you buy those? Is it also from givi?
Yes, the light kit was from Givi. This is the part I ordered, although it appears to be out of stock now.
www.revzilla.com/motorcycle/givi-e160-led-brake-light-kit-for-v56-top-cases?sku_id=1120978
Danke sehr.
Спасибо
Would it not have been easier to drill a hole?
Where to buy one? Thx!