Setting : P01: Backlight Brightness (1: darkest; 3: brightest) P02: Mileage Unit (0: KM; 1: MILE) P03: Voltage Class: 24V (default) /36V / 48V P04: Hibernation Time (0: never, other figures refer to the hibernation time) Unit: minute P05: Power Gear - 0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V 1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5: 4V P06: Wheel Diameter Unit: inch Precision: 0.1 P07: Magnet Steel Number for Speed Test Range: 1-100 P08: Speed Limit Range: 0-50km/h, parameter 50 indicates no speed limit. 1. Non-communications status (panel-controlled) When the current speed exceeds the speed limit, the PWM output will be shut down; when the current speed falls to lower than the speed limit, the PWM output will be activated and the driving speed will be set as the current speed ±1km/h (only applies to assist power speed, not applicable to the handlebar speed). 2. Communications status (controller-controlled) The driving speed will be kept constant as the limited value. Error Value: ±1km/h (applicable to both the assist power/handlebar speed) Note: The above-mentioned values are measured by metric unit (kilometers). When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly. P09: Zero / Non-zero Start Setting: 0: Zero Start 1: Non-zero Start P10: Drive Mode Setting 0: Power Drive - The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work. 1: Electric Drive - The vehicle is driven by the handlebar. In this status the power gear does not work. 2: Power Drive + Electric Drive - Electric drive does not work in zero-start status. P12: Assist Power Intensity Range: 0-5 P13: Power Magnet Steel Number: 5 / 8 / 12pcs P14: Current Limit Value: 12A by default; Range: 1-20A P15: Unspecified P16: ODO Zero-Out: Long press the upper key for 5 seconds and ODO will zero out
Thank you, very helpful! I kindly ask you to answer two questions: To disable the throttle should I set p10 to 0 ? Do you know where to find a list of error codes of that LCD panel? I got today error E07 while riding the bike uphill. It dissapeared after switching the panel off and on but it would be helpful to have a list of error codes. Thanks in advance.
Hi is it possible to have the PAS set to 2 for example but when i decide to use the throttle i get the full power of the motor as my throttle is dependent on the setting of the PAS. ie if its set at 2 then i get limited power from the throttle but if i set the PAS to 5 i get more power from the throttle which is irritating because if im going up a gradient and need a little more power than what the PAS is providing and press the throttle it stays at the same power unless i reach over and turn up the PAS?
You're very helpfull. Thanks! I was doing setup by LCD manual. Even with nice finish :) How about your max speed? Mine is about 20 km/h Bike received with some defects. I think wrong transport conditions. What about price? Mine for 660 USD. How are Your overall feelings about purchase?
@@TheSelstar I hope to get such a discount for mine defects seen and proven. Can You tell something more about service of this bike? I have white version. Battery is not in perfect conditions stored right now. I must do something. PS: My max speed for only electric mode was near 20 km/h :(
@@44plpatriot Power the bike off . Now hold the front brake lever and press the power on button down at the same time and keep both pressed for 30 seconds. Now power off the bike again. Switch it back on and try it.
Softwaregelocktes Geschwindigkeitslimit beim LO26 entriegeln: Display aus, (beide?) Bremshebel gezogen halten und dann Displayknopf mindestens 5 Sekunden lang gedrückt halten. :-) Verriegeln: Display aus, rechten Bremshebel gezogen halten und wieder mind. 5 Sekunden Knopf gedrückt halten (S830-Display geht dann an). So sollte es funktionieren. Komme entlockt auf ca. 30-32 kmh. Mehr wird der 350 Watt Motor vermutlich nicht schaffen. Ist bei mir dann das Maximum was geht. ;-)
I have error 7 and bike won't move when I twist the throttle. Any ideas on how to reboot the lcd to get rid of the error? Or any help greatly appreciated. Thanks
@@MrTechcat I managed to unlock the support up to 33km / h and on the throttle itself it accelerates to 30km / h but only when the battery is 100%. I will see you how you managed to unlock
hello have the same bike as you i have problem mine bike wont turn on it turn on only with charger do you experient this problem or anyone can give advise
@@achimsander2839 Thank you friend for your help is your answer I will give you a try in changing the speed and I will let you know if you do before me to do this test Let me know if this password works
@@renatopuopolo9591 There is a value information, but don't know if it's up to date: electricbikereview.com/forum/attachments/1528492757374_enoeco-user-manual-cs-s830-pdf.22814/
People on CZcams these days are such legends thanks for this video pal 👌👊
Setting :
P01: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class: 24V (default) /36V / 48V
P04: Hibernation Time (0: never, other figures refer to the hibernation time)
Unit: minute
P05: Power Gear - 0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V
Gear 4: 3.5V Gear 5: 4V
P06: Wheel Diameter Unit: inch Precision: 0.1
P07: Magnet Steel Number for Speed Test Range: 1-100
P08: Speed Limit
Range: 0-50km/h, parameter 50 indicates no speed limit.
1. Non-communications status (panel-controlled)
When the current speed exceeds the speed limit, the PWM output will
be shut down; when the current speed falls to lower than the speed limit, the
PWM output will be activated and the driving speed will be set as the current
speed ±1km/h (only applies to assist power speed, not applicable to the
handlebar speed).
2. Communications status (controller-controlled)
The driving speed will be kept constant as the limited value.
Error Value: ±1km/h (applicable to both the assist power/handlebar
speed)
Note: The above-mentioned values are measured by metric unit
(kilometers). When the measuring unit is switched to imperial unit (mile), the
speed value displayed on the panel will be automatically switched to
corresponding imperial unit, however the speed limit value in the imperial unit
interface won’t change accordingly.
P09: Zero / Non-zero Start Setting:
0: Zero Start
1: Non-zero Start
P10: Drive Mode Setting
0: Power Drive - The specific gear of the assist drive decides the assist
power value. In this status the handlebar does not work.
1: Electric Drive - The vehicle is driven by the handlebar. In this status the
power gear does not work.
2: Power Drive + Electric Drive - Electric drive does not work in zero-start
status.
P12: Assist Power Intensity Range: 0-5
P13: Power Magnet Steel Number: 5 / 8 / 12pcs
P14: Current Limit Value: 12A by default; Range: 1-20A
P15: Unspecified
P16: ODO Zero-Out: Long press the upper key for 5 seconds and ODO will zero
out
Thank you, very helpful!
I kindly ask you to answer two questions:
To disable the throttle should I set p10 to 0 ?
Do you know where to find a list of error codes of that LCD panel? I got today error E07 while riding the bike uphill. It dissapeared after switching the panel off and on but it would be helpful to have a list of error codes.
Thanks in advance.
Great video I loved it, but what about P13: what is the power magnet steel number? Do I set it on 5, 8 or 12 pcs??
What are the best set up for more power and more speed... Thanks
@@yahimmm2012 I want to know too
What's P11?
Thank You. Now work my bike too 👍
nice
Very helpfull👍
What kind of bike is this your programming
Got the same bike. Is there anywere a programm-instructions which value has which function at S830?
Hi friends but none of you understood yet how do you change the speed limit?
Hi is it possible to have the PAS set to 2 for example but when i decide to use the throttle i get the full power of the motor as my throttle is dependent on the setting of the PAS. ie if its set at 2 then i get limited power from the throttle but if i set the PAS to 5 i get more power from the throttle which is irritating because if im going up a gradient and need a little more power than what the PAS is providing and press the throttle it stays at the same power unless i reach over and turn up the PAS?
I just got a new one 2 days ago. May I know what these codes for? Thanks
How do you charge lo26 up
You're very helpfull. Thanks! I was doing setup by LCD manual. Even with nice finish :) How about your max speed? Mine is about 20 km/h Bike received with some defects. I think wrong transport conditions. What about price? Mine for 660 USD. How are Your overall feelings about purchase?
Hi friend how do you speed up?
@@TheSelstar I hope to get such a discount for mine defects seen and proven. Can You tell something more about service of this bike? I have white version. Battery is not in perfect conditions stored right now. I must do something. PS: My max speed for only electric mode was near 20 km/h :(
@@44plpatriot Power the bike off . Now hold the front brake lever and press the power on button down at the same time and keep both pressed for 30 seconds. Now power off the bike again. Switch it back on and try it.
Great video I loved it, but what about P13: what is the power magnet steel number? Do I set it on 5, 8 or 12 pcs??
There are 5 magnets:
czcams.com/video/wMPLATwHMAg/video.html
Softwaregelocktes Geschwindigkeitslimit beim LO26 entriegeln: Display aus, (beide?) Bremshebel gezogen halten und dann Displayknopf mindestens 5 Sekunden lang gedrückt halten. :-) Verriegeln: Display aus, rechten Bremshebel gezogen halten und wieder mind. 5 Sekunden Knopf gedrückt halten (S830-Display geht dann an). So sollte es funktionieren. Komme entlockt auf ca. 30-32 kmh. Mehr wird der 350 Watt Motor vermutlich nicht schaffen. Ist bei mir dann das Maximum was geht. ;-)
Can you precise the process in English please
@@davidbeduneau5925 For unlock 30km/h: with the display off, hold the right brake lever and then hold the M button for 5 second
I have error 7 and bike won't move when I twist the throttle. Any ideas on how to reboot the lcd to get rid of the error? Or any help greatly appreciated. Thanks
@@Sarah-kw7sp i have got the same pb. did you resolve it? thanks
@@Sarah-kw7sp green wire on pcb on motor may need resoldering for 07 code
Can anybody help I have a E09 code which is the controller eror, how do I fix it
hello i have the samebike as you my bike dont turn on only when the charger is pluged in do you have any advise about thise issu
You have to insert the key to the battery and turn it to half
Number 08 setup velocità
Ciao Renato te ne intendi un po di impostazione della samebike lo26?
hello you can post a video that explains how to unlock the speed thanks a lot
I have posted a video on my channel about Samebike speed unlock. :)
P08: Speed Limit
I have the impression that each of me has the same support, is it possible to set it? can you lift the speed limit and increase the power?
You can. I made a video on speed unlock and power limit removal.
@@MrTechcat I managed to unlock the support up to 33km / h and on the throttle itself it accelerates to 30km / h but only when the battery is 100%. I will see you how you managed to unlock
@@MrTechcat where Is video?
hello have the same bike as you i have problem mine bike wont turn on it turn on only with charger do you experient this problem or anyone can give advise
Use your key, insert it and turn it
Hello friends. The bike is off when i go to run with that. Whats happend???????? Im crazy. Thanks
Yes friend the password to be able to change the speed Thanks
Maybe it is standard bafang password: 0512
Give em a try.
@@achimsander2839 Thank you friend for your help is your answer I will give you a try in changing the speed and I will let you know if you do before me to do this test Let me know if this password works
@@renatopuopolo9591 also waiting for Our good friend to let us know. My max speed is 19.5 km for now. Very bad value.
@@renatopuopolo9591
There is a value information, but don't know if it's up to date: electricbikereview.com/forum/attachments/1528492757374_enoeco-user-manual-cs-s830-pdf.22814/
@@44plpatriot friend Try changing the maximum speed settings