How to: Program the Hobbywing 1080 ESC
Vložit
- čas přidán 13. 11. 2019
- We share our best settings for this best values rc crawler ESC
Buy it here: from Amainhobbies
Buy your kits and upgrade parts from this Amainhobbies link to support RC Review: snp.link/6640d084
Join the RC Review Facebook Group here: / 302319827122846 for early videos and extra footage. - Krátké a kreslené filmy
For #13, we pick the highest setting, #5 for the smoothest acceleration available.
The acceleration will be more aggressive at the initial stage when the drive frequency is low; a higher drive frequency is smoother but this will create more heat to the ESC
#13 will also change the sound of the motor. Below 8K you can hear it more (with higher or lower pitch). An higher PWM can also be more efficient in driving the motor. Yes the ESC will run hotter as the MOSFET transistor inside are dissipating more heat every time they switch state (the higher the frequency the more they switch), but the motor response to the input signal will be more efficient. This is a killer feature of this ESC imho. Being able to go high is great.
@@chiccorocker so what's best 5 ?
@@chiccorocker what do you set this to... or what are ALL your 1080 settings? I hope to add a 1080 to my arsenal as one of my next orders...
I was thinking, 8k , quiet, fairly smooth, one step from the highest to cut the heat level down a tad bit...
Wondering how you set the throttle and brake settings. I'm planning to run this with a 16t 5slot motor...
Everytime when I need to change a setup in my 1080, I come to this video LOL
Yep i have watched this one like 50 times
@@raymondmccauley9451 Me too hahahaha
Preach!
This guy did an awesome job at explaining the equipment setup. Finally got this little guy set up for my tamiya 1/14 scale truck!!
Love your videos. You have the best info out there. I have a TRX4 Blazer. My first crawler, and I don't add nothing until I listen to your video first. Thanks! 👍🏁
That is an incredibly helpful guide! Nicely done. I love the way you describe each setting one by one. Thank you for this!
Glad you enjoyed it!
Thanks! Bought this 3 years after the video for my FTR Mountain Rescue and this video helped alot! :)
Best video I have ever found on the 1080.Thank you very much.I am new to the hobby (10 months) and have learned enough to use the 1080 on all vehicles (5).I know, I went crazy. have searched everywhere and found a little info.By trial and error, I was VERY close to your suggestions.A few settings that I did not understand,you have helped me with.
Right on bud. Really appreciate your comment.
Awesome instructional video! This helped my wife and I set up our 1080. Thank you!
Thank you. More and more do I find your videos to be helpful and crystal clear on information. Keep them coming.
Thank you Francis for making this video. It helped me to better understand this esc and it's settings.
This is an excellent video, gave just enough explanation of each function to satisfy most people, I modified one setting based in my driving style (drag brake at 80%), the rest are exactly as in the video. Thanks!
Thank you very much, RC Review. I will wait for the settings of this ESC with great desire.
Omg thank you for posting this vid saved me doing trial and error testing saved me so much time and the settings are spot on
Love this esc. So smooth and so many setting options. And that price! Great vid brother!
I bought mine when my LHS was having a customer appreciation day. Got 20% off... Made my Frankenstein Tamiya CR-01 so much better
I love your videos! Thank you for providing them.
Hey thanks for the video !! Just built my first rock crawler with your recommendation. Of the hobby wing esc and fly sky transmitter. Wow just wow . Thanks for your Awesome videos . Great job! I've been out of the rc world for about 10 years. Was heavily into 3d helicopter, and planes . Now I'm back and into short course and rock crawlers . Thanks for your spot on reviews . Has been a wealth of tech savvy knowledge. Keep up the good work 😁👍. Oh and just incase your wondering I built the trx-4 sport build kit .
Awesome video! good explanations on what everything means and does.
Excellent Thank you buddy appreciate the help 😎🌇just finished reprograming the 2 I have
Just finished installing and programming the Hobbywing QUICRUN 1080 ESC. I used your recommendations, and it looks like they will be perfect for how I run my Axial SCX10 II 1956 Ford F100.
Great explanation, really useful and clear !
you guys are great. lots of knowledge. I enjoy all youre videos. keep it up. thanks
I needed this video, thank you! Your videos are the best.
You're so welcome!
got a competition next week, and got this baby in a MST CFX, a class 1 unimog, thank you!
Oh man thank you so much for this setup Bro. I just dropped the 1080 in TRX4 and oh my gosh. I’ve never experienced such control and a bec beefed up before. I’m so giddy right now.
Thank you for this! I appreciate you and what you do!
great breakdown mate and with your endorsement i have mine on the way
Thank you Sir !! Great great content. Helpfull! Entertainment! Everything
One of the best video for information quality, explaining really well some not clear configuration points (expeciall "freewheel", but some other too).
I have bought one recently and paying with settings is really enjoyable !
Good job, thanks !
Amazing..Thank you for posting this.
thank you so much, the best information on line, !!!!
Thanks for all your knowledge. Whatever I have to fix I just look it up on your channel seems like you’ve fixed everything. If only there was a video out there for trucks with leaf springs. How to keep them from flattening out
Thank you! Such a great help. You rock.
More great information!
Thanks
Thank you for the great video !
Really really useful video, thank you.
thank you!
Awesome video 👌 thanks so much!
Awesome, dude! Thanks a lot! 😃
Tanks, very good explaining👍👍👍👍👍👍👍👍👍👍
Very very usefull and great explained
appreciate it!
Thank you very much, helped me a lot
Brilliant help thanks 👌
Awesome video thanks
Fantastic video :) thx
thank you for doing this vid
You kind of bobble number 15, but then nail it with granular control during descent. I find it useful to enable Freewheeling first since Fw tends to make its presence felt elsewhere--particularly drag brake. With Fw enabled I drive some steep ramps while dialing in the rest. Great video. Thanks for doing this.
Right on bud.
Great video, it’s bout time I turn my truck into a boat 😁
You can do it!
Very helpful 👌
I used your settings for my vanquish ultra, perfect! Thank you! btW How does this ESC handle lihv batteries, any issues?
I hope to someday get a 1080 ESC... I've got the 1060, and love it - at least after I made a twin Capacitor Glitch suppressor for it.
You're RIGHT! The print on all Hobbywing products are MICROSCOPIC!!! 😡😠 My 55 year old eyes have trouble with it. Good tip for screenshotting it!
Carmine ✈🚂🚙
I need this for the “freewheel” setting. That is specifically what i was looking for in a esc. Didn’t know what was called. Thx
Awesome video!! Can you please do a video like this on the hobbywing axe system 😁
when setting the bec to 7.4 V and the servo can handle that doese it matter whatvoltage the reciever can handle?
Perfect for my Panda x1 6x6 :)
Really helpful - thank you. One question... The settings in the video differ to those shown on-screen at the end for settings 4, 6, 8, 10, and 13. I went with the ones discussed in the actual video.
Matt C I noticed this exact thing. I watched the video and took notes throughout the video and it differs from the numbers towards the end if you want to just go all the way to the end to see the numbers but it’s different. I wonder why what he discusses contradicts the numbers that are at the very end?
Hi. Thanks for an excellent instructional video. Perfect!!!! Please share which servo you use.
very well explained,
Does the quality of the radio influence the result?
Can you explain what the FREEWHEELING function does?
Where to connect a program card that esc come without input for program card?
So I'm using the same flysky controller and I was wondering do you leave your dual rate down? Have you used this controller on a sensored brushless esc with turbo and timing modes?
Do you have any driving / testing/ adjusting videos for this esc? i'm super interested in "a day in the life using the HW 1080"
can a sx107 micro servo handle 7.4 volts is for the dig on capra
Hey guys! Nice video as always. What kind of front/back bumper do you use for the element? / Kim
Thank you
You're welcome
Trying to set up my new one and it doesn’t beep at all?? Please help. Tried reversing the motor cables several times, made sure the plug is in receiver correctly
How would I program this speedo for an f1 car? I don’t want brakes as they make the car spin, but I don’t want to go straight into reverse either.
You said “the white wire should be closest to the outside edge of the ESC.”
White wire should be towards inside, not outside edge.
Lol yeh he got it wrong
Hi, I'm new to the hobby. Does 80% drag brake have the same braking force as 80% manual brake?
So I did what you said and my esc the led just blinks and I have no power help please
How do I configure my esc with new transmitter, if I buy it?
Do you have an instructional video like this for the axe 2800kv system? These are extremely helpful for setting up a nee combo.
Is this esc supposed to flash while moving the vehicle fwd/rev??
It seems to be working fine.
If i recall correctly when moving with the traxxas esc, the light stays steady..is this just a different design??
Can I run trx4 stock 2075X servo and tqi receiver with 1080 ESC on 7.4v?
hi thx for the video, i still have one question, in number 14 the voltage to the servo that voltage only goes to the steering servo or also goes to for exemple in the trx 4 to the differential servos?
The BEC voltage will be what is feeding from the ESC into the Reciever, then from there into the rest of the system...so reciecer, servos, leds, anything connected to the reciever basically...
I will be disabling the BEC that is internal to the speed control, and using a separate standalone 10A BEC from Castle(about 23$). I'll be running on 3s lipos, powering a reciever, a few servos and other bits, as well as some lights...
Dear friend, please explain what 13. PWM FREQUENCY is. Thanks
Can I use this with the stock trx4 sport motor(titan 550 21T)
This is what concerns me being new to RC. This is in the product description on Amazon for the ESC.....Motor Limit 3S LiPo: 16TSize
Is 16T the highest T motor that can be used, or the lowest T motor that can be used??
is it the same program card for the G2?
Hey Francis, thank you for sharing your knowledge here! What i found out: If you run it in in Forward/Reverse mode, the Brake is disabled and so Parameter 7 (Max. Brake force)and 8 (Initial Beak Force)has no more function.
Maybe i missunderstood something, let me know... Thanks!
This makes sense, in fwd/rev mode, the only brake action is drag brakes... wondering if the 8th setting option makes it start softer and ramp up to your drag brake setting? I haven't gotten my 1080 yet...
Would u tell me the settings you use?
I have the quick run. But I'm getting no power or steering. I'm new to the hobby and feel stuck. I have a tamiya tt02d with absima transmitter sr2s. Quick run esc and a cheap servo.. what am I doing wrong. Can't even get my first kit car going
Please would it be possible for a link to the radio that your using. Thank you Jo
I got my 1080 hooked up when I power on I heard the servos work. But I have no steering, throttle, or reverse any ideas
That's 100% a radio or reciever problem
Hey Nice video I usually watch your videos all the time, I have a question about this Hobbywing 1080 esc, I recently installed 1 on my axial scx10 II and 2 days ago my servo stopped working, because the servo circuit burned out and since that day My esc works like crazy, (it did not turn off when I hit the power button) and today it did not work when I turned it on the esc, the power led is flashing and esc does not turn on ... Please, I need help with this.
Can I use esc 1080 with 2 motor rs775 DC motor
can anyone tell me what flsky transmitter he uses
#RCReview - I have a few questions - i just got the Dynamite LED Program Card (DYNS3005) and I am trying to figure out if this will program my ARRMA Notorious that has a Spektrum SR60100AT DSMR w/ AVC Telemetry receiver thats installed, also what port should I plug into the bind port or the one of the AUX ports?
I don't think that works. The Dynamite LED card is for programming the SPEKTRUM™ FIRMA™ SMART 40A BRUSHED 4-CHANNEL ESC/RECEIVER. It's for programming the motor functions only.
Sending my gift. Hope to see u around
how come you didn't talk about #13
Exocaged has a good video showing the PWM setting...and how it affects noise.... higher makes less noise, can be smoother, but also creates less heat.... i plan to use 4k or 8k when mine arrives...and going to try not using the highest setting for less heat, as I will be already running on 3s lipos with a 16t 5slot(supposed to be similar to 35t)...
Hello. Can you show how to calibrate the 1080 with the flysky GT5, please?
What if you just have lines ?
What is setting 13?
How many volts can the skyfly reciever take?
I wondered the same, as far as other parts of the system liking 7.4v...
I habe a 1080 coming, but plan to use it with a rig that has lights, steering, reciever, and some other bits...also plan to use 3s lipos, and that is usually harder on a BEC... I looked up the BEC spec and it says 3A.... I will be adding a CC BEC as i usually do in our trail rigs.
Can someone help? After installing the hobbywing esc I can only use the traxxas tq remote in 70/30 and not in 50/50 mode. If I put it in 50/50 the car automatically accelerates and a constant slow speed. I’m not a fan of the 70/30 and I would like to revert it. Please help.
You have to calibrate the esc while in 50/50 mode
traxxas receiver can take 7.4v?
Hey on ur last chart you got it wrong. 6.0?
Has anybody else had trouble programming the 1080? I press the set button and power at same time it starts up I keep in in nutral then press black button again and it stops? I have a gt3b radio please help
Francis. You skipped over the #13 PWM Frequency setting. Better put on those glasses...LOL
7.4V BEC on an Annimos 25mg will work but burn out on a stock TRX-4 radio, though right?
Thinking same but 20 bucks if last a year its good
@@paulclancy2404 A new receiver isn't $20 though, I think you're thinking about the servo. I'm more afraid of the receiver failing.
@@LeftenantMalachi oh yes i was , it cant be tactic or traxxas not sure about fly sky i prefer futaba but spectrum can handle 9.0 volts i was thinking about getting flysky even better one but this one 37 bucks i hear works just as well
Hopefully you are still checking this video. If you upgrade a TRX4 to something like this ESC how can you use the BEC options without frying your small servos? Are there multiple BEC connections that you can keep some at 6v and some at 7.4?
What are your settings on the Skyfly transmitter?
Nothing fancy. Just perfect end points and maximize the modulation and slow control.
My wp1080 is stuck on calibration mode can somebody help
Thanks! This is very helpful! Why did you skip setting 13?
Sorry, that was an oversight. We pick the highest setting.
The acceleration will be more aggressive at the initial stage when the drive frequency is low; a higher drive frequency is smoother but this will create more heat to the ESC
Apology not necessary. No doubt with the tiny writings on the program card it can easily be overlooked. Thanks for the additional info. 👍🏽... you’re the man!