Great video review...Thanks. I recently bought this device to use in motor mode for the shutters. Then I have connected a RF remote to it as well, with Open/Stop/Close buttons. The problem is that when I add scene trigger for Dual R3, there is NO Stop function, only Open, Close, and Open Percentage!!! It's frustrating because in a typical remote, I should be able to stop the motion anytime I want, right? I can't believe this simple trigger is not available. Is there a way around it? Thanks
Excellent video looking for this solution sometime now... some questions if you could answer to me: 1. Is there a reset function on the app for the switch, in case you want to reset it without opening the socket to press the button ? 2. Have you tried to fit it, in a EU Socket box ? 3. The original blind switch still remains fully functioning? 4. As the blind is operating from the app can you still press the physical switch and bypass the app i.e. Routine opens or closes the shutter but you want it to stop one of the shuttters can you bypass it with the physical switch? (hope it makes sense :) ) Thank you
Reset: I am not sure what you mean. How you want to reset it? I did not see such features, so no. You can turn off your circuit breaker... 2: No I did not, but you find the dimensions on Sonoff official website. 3: You can install the original switches in parallel with the Live outputs. That would work, but when you use the switches the app will not now that the blinds have moved and will not show an accurate position. 4: to be honest I did not test that. I assume the button always overrides and automation.
Whatever you said about motor calibration for shutters makes perfect sense only it just does not work like that. I hit calibrate and turns the motor off and stops there. Could not find any official procedure.
Szia Csongor, azt szeretném megkérdezni, hogy szerinted lehet a kapcsoló és a motor módot használni egyszerre? Úgy értem az egyiket az egyik áramkörön a másikat a másikon. Van egy elektromos redőny motorom és mellette egy szellőztetőm. A szellőzőhöz áramkör megszakításra lenne szükség a motorhoz pedig a motor módra. Ha lehet akkor nem kellene 2 sonoff eszköz a kötődobozba. Köszi.
Szia Csongor! Először is köszi a videóidat, nagyon hasznosak! Olyan sokat vártam egy sima RF fali kapcsolóra, hogy vagy elfelejtettem amit akartam, vagy az alapötletem volt hibás... :) Szerinted van bármi esélyem arra, hogy egy R3 mini + SNZB 03-as mozgásérzékelő alkotta rendszerbe beillesszek egy manuális RF433-as kapcsolót (RF és Zigbee bridge is van)? A cél, hogy az egyébként jól működő mozgásérzékelős kapcsolás kiegészüljön egy manuális lehetőséggel. Előre is köszönöm, ha tudsz valamit javasolni!
Szia, szivesen. Uh, nagyon regen használtam már a sima RF-et. De szerintem menni fog. Annyi lesz a baj, hogy amikor RFfel kapcsolod fel a lampat, akkor lehet hogy a mozgaserzekelo is bele fog szolni es o lekapcsolja. Szerintem kezd azzal hogy megcsinalod SNZB 03 és a R3 mini Scene-jeit. És aztán amikor az RF kapcsoló Scene-jét definiálod, akkor azon túl hogy felkapcsolod a R3 mini-t, kikapcsolod a mozgásérzékelő Scene-jeit. És lekapcsoláskor pedig vissza. Én akkor ha kézzel irányítod a lámpát, a mozgásérzékelő nem fog beledumálni.
@@csongorvarga ez volt a kulcsmondatrész: "És aztán amikor az RF kapcsoló Scene-jét definiálod" - Az SNZB és az R3 rendben működik hetek óta, csak az RF érkezett most meg. De a lényeg, hogy egy scene-t kell létrehoznom a kapcsolóval és ezután ezt a scene-t már hozzárendelhetem. Na akkor ezt gyorsan kitalálom, hogyan kell ! Köszi, szerintem átbillentem a holtponton :)
@@tomujj Igen, és ha jól emlékszem akkor a gombot nem buttonként hanem alarm-ként kell definiálni. És nem fogod egy gombbal megcsinálni (szerintem), hanem kell egy bekapcsoló és kikapcsoló RF gomb.
Mindenben igazad lett és sikerült ügyesen beállítani pont azt amit szerettem volna: WC a helyszín :) Mozgásérzékelő nappal fehéret kapcsol éjszaka gyenge fényű zöldet. Mindkettő 3 perc késleltetéssel lekapcsol automatikusan (gyerekbiztos :)). Ha a megadott 3 perc kevés lenne (vagy bármi miatt éjszaka kell nagyobb fény), akkor az RF kapcsolóval felkapcsolható a fehér fény, ami szintén 3 perc múlva automatikus lekapcsol. Köszönöm!!!
Kedves Csongor! Nemrégiben szereztem be egy Dual R3-at és szomorúan vettem észre, hogy nem fér be a már meglévő fali dobozba (kb 5 mm kellene hozzá). Szerinted, ha veszek 2 db Zigbee Minit, be tudnám kötni a már meglévő 2 gangos kapcsolóhoz? A kapcsoló mellett rögtön van egy dugalj is, ahova be lehetne rakni a másik minit. A problémát nehezíti, hogy a kapcsolón 1 be - és 2 kimenő csatlakozási lehetőség van. Alternatívaként ott van még a TX széria, de az sem férne be a meglévő dobozba és csak ezért nem akarnám megbontani a falat, valamint ragaszkodnék a billenő kapcsolóhoz.
Szia, igen két mini ugyan azt a funkciót tölti be mint egy dual. Viszont sokkal többet kell kábelezni, remélem azt nem lesz gond. A kapcsolókon általában 2 kimenet van, hogy alternatív kapcsolásban be lehessen kötni. Használd az egyiket.
@@csongorvarga Megnézem mégegyszer majd jobban a kapcsolót, ha lesz időm, mert mintha úgy láttam volna, hogy csak egy szál vezeték fér be egy csatlakozási pontra. Azért nagyon köszönöm a válaszod és, hogy megerősítettél abban, hogy ez így működne.
Sorry, I do not understand English well and did not understand from the video, is it possible to configure this relay to alternate operation of channels? That is, if the first is on, the second is off. And if the second is on, then the first is off.
For my roller shutter I use a "normal" Sonoff Dual. When I use "Interlocking" the feature "Schedule" isn't available. Does this Sonoff Dual R3 combine those 2 features?
I am away from home now and my device is offline, but still I can see that the device is in motor (blind motor) mode and there is a schedule button at the bottom of the screen. So the answer is Yes it does support Schedules.
Grate video! I am searching for something similar (I am want only the motor function for blind) but I want to be compatible with apple homekit. Can anyone recommend me a device ?
Sorry no. Homekit is a completely different system. If you search in Aliexpress for "HomeKit" there are a few devices available. Based on the screenshots in the listing they do work with homekit.
@@delaveganz So I only have a Google Home. On your Home app you click Add, "Works with Google" and then you need to link your ewelink account to your Google Home. After that all your ewelink devices will also appear in the Home app. I am not sure how that works for Alexa.
@@csongorvarga I already have many older Sonoff devices on Google Home. When I rescan, the Dual R3 does not show up. I guess that is why the package does not have the works with Google Assistant logo :-(
Great review! Really wanted to see how the scenes worked with the 2 inputs/outputs and you answered all my questions!
Great video, thanks ! This contained LOTS of useful info. You should ask Sonoff to pay you ! 😉
Great video review...Thanks. I recently bought this device to use in motor mode for the shutters. Then I have connected a RF remote to it as well, with Open/Stop/Close buttons. The problem is that when I add scene trigger for Dual R3, there is NO Stop function, only Open, Close, and Open Percentage!!! It's frustrating because in a typical remote, I should be able to stop the motion anytime I want, right? I can't believe this simple trigger is not available. Is there a way around it? Thanks
Hopefully they will do ZIgbee versions.
Excellent video looking for this solution sometime now... some questions if you could answer to me:
1. Is there a reset function on the app for the switch, in case you want to reset it without opening the socket to press the button ?
2. Have you tried to fit it, in a EU Socket box ?
3. The original blind switch still remains fully functioning?
4. As the blind is operating from the app can you still press the physical switch and bypass the app i.e. Routine opens or closes the shutter but you want it to stop one of the shuttters can you bypass it with the physical switch? (hope it makes sense :) )
Thank you
Reset: I am not sure what you mean. How you want to reset it? I did not see such features, so no. You can turn off your circuit breaker... 2: No I did not, but you find the dimensions on Sonoff official website. 3: You can install the original switches in parallel with the Live outputs. That would work, but when you use the switches the app will not now that the blinds have moved and will not show an accurate position. 4: to be honest I did not test that. I assume the button always overrides and automation.
You seem to have the live and neutral reversed judging by the colors of the cables
I was using a EU plug for testing, which can go either way anyway. But thanks for spotting.
Whatever you said about motor calibration for shutters makes perfect sense only it just does not work like that. I hit calibrate and turns the motor off and stops there. Could not find any official procedure.
Me too...calibration not working..
Same for me, calibration start and stop in 1 second and that's everything, waste of money
Szia Csongor, azt szeretném megkérdezni, hogy szerinted lehet a kapcsoló és a motor módot használni egyszerre? Úgy értem az egyiket az egyik áramkörön a másikat a másikon. Van egy elektromos redőny motorom és mellette egy szellőztetőm. A szellőzőhöz áramkör megszakításra lenne szükség a motorhoz pedig a motor módra. Ha lehet akkor nem kellene 2 sonoff eszköz a kötődobozba. Köszi.
Nem lehet. Mármint egy redőny motornak két bemenete van. Nem tudsz ahhoz csak egyet használni...
Szia Csongor! Először is köszi a videóidat, nagyon hasznosak! Olyan sokat vártam egy sima RF fali kapcsolóra, hogy vagy elfelejtettem amit akartam, vagy az alapötletem volt hibás... :) Szerinted van bármi esélyem arra, hogy egy R3 mini + SNZB 03-as mozgásérzékelő alkotta rendszerbe beillesszek egy manuális RF433-as kapcsolót (RF és Zigbee bridge is van)? A cél, hogy az egyébként jól működő mozgásérzékelős kapcsolás kiegészüljön egy manuális lehetőséggel. Előre is köszönöm, ha tudsz valamit javasolni!
Szia, szivesen. Uh, nagyon regen használtam már a sima RF-et. De szerintem menni fog. Annyi lesz a baj, hogy amikor RFfel kapcsolod fel a lampat, akkor lehet hogy a mozgaserzekelo is bele fog szolni es o lekapcsolja. Szerintem kezd azzal hogy megcsinalod SNZB 03 és a R3 mini Scene-jeit. És aztán amikor az RF kapcsoló Scene-jét definiálod, akkor azon túl hogy felkapcsolod a R3 mini-t, kikapcsolod a mozgásérzékelő Scene-jeit. És lekapcsoláskor pedig vissza. Én akkor ha kézzel irányítod a lámpát, a mozgásérzékelő nem fog beledumálni.
@@csongorvarga ez volt a kulcsmondatrész: "És aztán amikor az RF kapcsoló Scene-jét definiálod" - Az SNZB és az R3 rendben működik hetek óta, csak az RF érkezett most meg. De a lényeg, hogy egy scene-t kell létrehoznom a kapcsolóval és ezután ezt a scene-t már hozzárendelhetem. Na akkor ezt gyorsan kitalálom, hogyan kell ! Köszi, szerintem átbillentem a holtponton :)
@@tomujj Igen, és ha jól emlékszem akkor a gombot nem buttonként hanem alarm-ként kell definiálni. És nem fogod egy gombbal megcsinálni (szerintem), hanem kell egy bekapcsoló és kikapcsoló RF gomb.
@@csongorvarga mindenképp visszajelzek - tényleg köszi a segítséget!
Mindenben igazad lett és sikerült ügyesen beállítani pont azt amit szerettem volna: WC a helyszín :) Mozgásérzékelő nappal fehéret kapcsol éjszaka gyenge fényű zöldet. Mindkettő 3 perc késleltetéssel lekapcsol automatikusan (gyerekbiztos :)). Ha a megadott 3 perc kevés lenne (vagy bármi miatt éjszaka kell nagyobb fény), akkor az RF kapcsolóval felkapcsolható a fehér fény, ami szintén 3 perc múlva automatikus lekapcsol. Köszönöm!!!
Sonoff Dual R3 doesn't mention compatibility with Amazon Alexa, Google Assistant, IFTTT or Google Nest in the website (unlike Dual R2)
Actually, web site says:
Works With Google Nest No
Works With Amazon Alexa No
Works With Google Assistant No
EWeLink Support Yes
Is this enough for water heater (home) it is 2000W device
Thank you
2000W is right on the limit, I would not do that. I would rather use something oversized for such a big consumer, like a POWR3
Kedves Csongor! Nemrégiben szereztem be egy Dual R3-at és szomorúan vettem észre, hogy nem fér be a már meglévő fali dobozba (kb 5 mm kellene hozzá). Szerinted, ha veszek 2 db Zigbee Minit, be tudnám kötni a már meglévő 2 gangos kapcsolóhoz? A kapcsoló mellett rögtön van egy dugalj is, ahova be lehetne rakni a másik minit. A problémát nehezíti, hogy a kapcsolón 1 be - és 2 kimenő csatlakozási lehetőség van. Alternatívaként ott van még a TX széria, de az sem férne be a meglévő dobozba és csak ezért nem akarnám megbontani a falat, valamint ragaszkodnék a billenő kapcsolóhoz.
Szia, igen két mini ugyan azt a funkciót tölti be mint egy dual. Viszont sokkal többet kell kábelezni, remélem azt nem lesz gond. A kapcsolókon általában 2 kimenet van, hogy alternatív kapcsolásban be lehessen kötni. Használd az egyiket.
@@csongorvarga Megnézem mégegyszer majd jobban a kapcsolót, ha lesz időm, mert mintha úgy láttam volna, hogy csak egy szál vezeték fér be egy csatlakozási pontra. Azért nagyon köszönöm a válaszod és, hogy megerősítettél abban, hogy ez így működne.
Does it work Without Neutral wire?
No, this needs the neutral wire.
Sorry, I do not understand English well and did not understand from the video, is it possible to configure this relay to alternate operation of channels? That is, if the first is on, the second is off. And if the second is on, then the first is off.
Yes, that is basically the motor mode, that is designed for blinds. It either goes up, or down, or completely off.
For my roller shutter I use a "normal" Sonoff Dual. When I use "Interlocking" the feature "Schedule" isn't available. Does this Sonoff Dual R3 combine those 2 features?
I am away from home now and my device is offline, but still I can see that the device is in motor (blind motor) mode and there is a schedule button at the bottom of the screen. So the answer is Yes it does support Schedules.
@@csongorvarga Thank you for your response. I know it does support Schedules, but does it support Schedules when Interlocking is enabled?
12:35
Motor mode
Grate video! I am searching for something similar (I am want only the motor function for blind) but I want to be compatible with apple homekit. Can anyone recommend me a device ?
Sorry no. Homekit is a completely different system. If you search in Aliexpress for "HomeKit" there are a few devices available. Based on the screenshots in the listing they do work with homekit.
Whats the difference to the Shelly 2.5?
I think they are pretty much identical, but this works with Sonoff devices, and Shelly works with Shelly devices. So only the ecosystem is different.
Does this work with apple
eWeLink app is available for iOS that is the only way to use it.
does it work with google home?
Yes it does
@@csongorvarga - I tried and it does not seem to integrate with Alexa and Google?
@@delaveganz So I only have a Google Home. On your Home app you click Add, "Works with Google" and then you need to link your ewelink account to your Google Home. After that all your ewelink devices will also appear in the Home app. I am not sure how that works for Alexa.
@@csongorvarga I already have many older Sonoff devices on Google Home. When I rescan, the Dual R3 does not show up. I guess that is why the package does not have the works with Google Assistant logo :-(
@@csongorvarga ITEAD website states:
Works With Google Nest No
Works With Amazon Alexa No
Works With Google Assistant No
EWeLink Support Yes
is too big in order tu use US wall box :(
Sadly it too big for EU wall box too :(
wifi = minus
only zigbee
Bugged automatic calibration is a nightmare and make this device useless, waste of money