#PAM8610
Vložit
- čas přidán 25. 07. 2024
- Detail review and wiring of #PAM8610 stereo amplifier module. Pricesiwise its a good quality audio board. Suitable for boom box and bluetooth speakers.
It has output power of 10 + 10 watt with 12 volt power supply and 8 Ohms speaker Load.
You can buy this board from here
amzn.to/37F7mRd
amzn.to/2OaEoAK
amzn.to/38MmP1O
amzn.to/2O8qteQ
#CLASSD
#DIGITAL AMPLIFIER. - Věda a technologie
AAP bahut achha detail me videos banate ho
I'm big fan
Good sar aap bahot achi tarah se jo samjate ho is ke liye sukriya...or sahi mahiti jis tarah se dikha te ho is k liye sukariya ..
Sir ap bahut accha detail review dete hai
Nice video bro. I Love your all videos & there's lots of knowledge in your videos.❤️
सर, आपकी आवाज़ और समझाने का तरीका बहुत अच्छा है.
आपने IC के पास पॉजिटिव और ग्राउंड पर 100 - 200 uf केपेसीटर लगाने का सजेसन दिया था. (वीडिओ टाइम 2:40 से 3:05) इसे भी प्रेक्टिकली बताते तो हम जैसे हॉबीस्ट नए लोगों को और ज्यादा फायदा होता।
Bohot achha explain Kiya....tqu sir
Thanks bro me yhi video dhoodh rha tha bhut shiddat se . Thanks yaar 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Namaskar sar bahut acchi video hai aapki bahut hi badhiya
Hissing sound is coming due to ground looping as u have given power from same source.Give separate 5v dc to bluetooth module to reduce hissing sound. U can use a old mobile charger circuit for the bluetooth module as separate 5v dc.
Nice video sir. Keep up the good work
Dada, Main PAM 8403 IC Wala Amplifire Board Use Kiya hu, Mai is me 8 Ohom's,2.5Watt ka 4" Speaker Lagaya, Sound Quality Bohot Ach6a He, Aur Bohot hi Loud Sound He Isme.
Sahi baat hai...bhai ji sahi baat karte ho app lo ek LIKE hamare taraf se👍 nice video..
On my TPA 3110, they have attached same lm7905 IC for 5v supply..and it works fine with any distortion at all, don't know what the problem with this board is...
I think the sound box you are using is of 4 or 6 Ohm, will they harm the amo as it is recomended to drive 8 Ohm? and in such low Ohm load the sounds seems okay with no clipping. here what to do to prevent clipping?
Thanks for video
Please make a video on passive crossover circuit as well
Sir full range speaker pe koi video banaye ki kaha se kharide aur pricing and sound test too
Awesome board
Thanks bro
शानदार👍
सर कृपया op amp पर भी वीडियो बनाइए
जिससे कई amplifier connect हो सके
sure..
Kya agar 5.1 home theater 2050 ic wale kit me two subwoofer 5.25 ya 6 inc ka subwoofer laga sakte hai
Bhaiya bohot sare log jo 12v transfermer less power supply bnate hi pf ,ziner diod bgera lgake kya ye Circuit 8610 work krega kyuki adaptor ya transfermer bohot mehenga aata hai isliye
Apke bahut vedio dekhe u r amazing. U r Indian electronic man with hi fi knowledge 💖u bro
NCS ke music kitne ghatiya hote h but apke video ache h❤️ keep it up
Sir there was a ic numbered ht8696 please make a detailed video on it and also hot to connect car 4.0 bluetooth module with it.
Sir aap isko bridge mode me convert kr sakte hain ky ..jaise 6283 board ko 15 k resistor se short kr ke bridge me chla skte hain .....
Hey what's the Best amplifier for 1 speaker+ 1 subwoofer?.. thanks
good work 👍👌 brother
Best review
Mene pam8403 se bt speaker banaya but wo radio ki tarah bajta hai no bass 😂😂😂
Apne voltage regulator par kaun se value ke dono capacitor lagaye hai please bataiye please
@WhatIThink i am making a project and having problem, i have a pam 8610 connected to 20watt 4ohm + 10watt 4ohm speakers in series on both channels so 8ohm per channel and power supply as 3x 18650 batteries, input from 5v Bluetooth module which gets power from a 7805 regulator , i have also added capacitors between battery and amplifier of 4700uf+1000uf and a 22k resistor on sound output from Bluetooth module to reduce distortion but it still has a lot of distortion and clipping and most song are not even listenable and a voltage drop of 0.2-0.4v while running plus the chip runs hot even having heatsink on top, pls help i am stuck
Bro muje ek sound bar bnama hai to ek video banao us par jisme fm / card/ or usb and full remote control ho
Sir which battery to use to make a small Bluetooth speaker if connect the battery 3cell 12v battery it get turned off after 3-4secounds when the volume is turned up
Pls suggest the best pair of speaker for this pam8610......🙏🙏
Is board mein volume control laga sakthe kya, please reply
sir.. muje lagta he noise apke low qualitie bluetooth module se ah raha he
👍 mai bhi use karta hu 3 bord 5.1 ke liye koi noise nahi hai
Battery use karne se noise nahi aati
Yes Right Bro Isme Koi Bhi Bluetooth Module Lagado Ye Noise Hi Dega Agar Aap Is me Neckband Connect Kar doge toh koi noise nahi aayega 1000000000 percent
Sir, 3110 aur 8610 me kounsa achcha hai....2inch ya 3inch speaker ke liye...strong and quality sound chahiye 🙏
Sir bluetututh kit ka input ma agar ashahi do board ko agar lagaiange to kya board ka gain kam ho jai ga
Same problem i faced sir, noise/ hiss at even low or no volume unlike TPA 3110 which is comparatively quite even though both have similar distortion levels as per data sheet
Use separate powersupply for Bluetooth and Amplifier
sir is there ny other amplifier for 10 10 watt speaker which will not create noise at hight volume
Noise suppression pe techniques chaiye ...
Bass treble kit laga sakte hain kya ?please tel me
Which components use in your bt power supply
Pam 8610 pr perfact power suplly kitne voltt deni chyee kiya liptop wale charger laga sakty hen
Can we use Mt3608 booster for power?
Then how can I amplify 15watt output? That means that have I to use separate amplispeaker for each channel?
Bhai mere pas philips ka 'spa150' 2.1 speaker hai. jiska bass ic EG 8371 jal gya hai or ye ic mil bhi nahi kya kare. Kya koi or ic lga sakte hai😢
Sir ek dout tha pam 8610 ya tpa 3110 kon sa best ai
sir tpa3110 aur pam8610 me konsi best hai
Nice video
Sir ye same 2 pc 3inch 4ohms 10 watt ka speaker chalane ke liye 12 volt ...kitni ampere ka SMPS lagana hai .......?????? Please
Sir 8w or 4ohm ka do speaker 8610 ke amplifier se chala sakte hai
Sound quality kesi milega 2inc 10w speakers pe 12v pe on this board pls reply
Sir namaskar. Pam8610 ko 12v transfermar 3amp se chalaya or bluetooth module ko 3.7v lithium ion battery se par bluetooth module excess hit kyu hai.please guide me kindly
Sir.
My 6810 module.
When i connect power to the module
No sound. but when i short switch mode sound comesout for the few seconds again goes to off mode.
Can u suggest me why it is happning.?
Hello, I recently used an online calculator to calculate the crossover circuit coil. Which I made out of 23 awg wire 1" height and 7layers of 40 turns. To get appx 900 mh. When i tested the resistance it was 2ohms on each coil. I installed the circuit on my 4 ohm hi and low drivers and now the overall impedance is 16 ohms. I am using a dual 4440 ic amplifier. Can you please suggest me where I went wrong or is that normal that after installing crossover the impedance increases?
Use thicker wires to make passive cross over...May be the wires which you are using to connect the amp to speaker are too long and cause of extra resistance ..Connect cross over direct to speaker then chek the impedance
Better to use active crossover instead of passive.
I will check as directed and will update you. I am using 2x4440 and one tda203 amp to make a 5.1 home theater system. But the output is not what I am expecting. I would love to share the pictures. I am using 3amp 12 volt transformer om 4440 and 15-0-15 1.5 amp on 2030. Also I modified one normal vocal woofer to accommodate a subwoofer coil. And have connected 2x8 ohms in series to make it lesser impedance. One last thing. Thank you so mich sir for all the valuable information you shared. I have never seen any CZcams channel as organized and well presented on electronics. I am an electronic enthusiast and have learned these some on my own and some from teachers like you.
Best video
Sir TPA3110 class d amplifier board ka details bataiye...wo kaisa board hai?
What is the solution for noise?? And power supply kitna amp ka rakhna hai???
Nice audio
How is the bass quality?
Can I use it for 16 ohm 10 watt 2 speakers 🔊🔊🔊 please reply 🙏
Sir ye bataye ki apne jab chote Wale speaker lagaya ta to wo 10 w ke te par oms kitne te
Bhai hmm 12 - 0 - 12 2amp 12v transformer use Kar sakte h issme????
Power supply is of 12 volt. Full range speakers are of 4 inches 30 watt each connected . Still voice is cracking at volume above 60 percent. Any idea
Khud se potentiometer lga kr volume control kr skte hai?
When i connect amplifier board pam8403 and bt module with one battery then annoying beep sound come how can i fix this please help me
Sir PAM8610 board mein 4 inch ka kitne ohms aur kitne Watt ka speaker use kare
Mera 3 way speaker 4 inch hai 30- 210 watt ka 4ohm ka 2 speaker hai kon sa amplifier board use kare
Second wala jo speaker use kiya hai wo kitne watts Ka hai??
Dada, TDA 2050 IC wala Amplifire me Kitna Ohm's, Kitna Watt's ke Speaker Best Hoga? Agar Is Amplifire Ko 12-0-12 Volt's ki Tranformer se Chalau to.Aur Transformer Kitna Ampere ki Used Karu?Aur Kitna Inchi Ka Speaker Used Karu?
Bh.. Kya hum isko 500ml Ampere se chla sakte hai
12v 500ml Ampere
Tpa 3110 d2 vs Pam8610 best amplifier for 10w 4ohm speaker
What is the SW port? What is the use of it?
Hii,here iam using this bord,but when i connect it to speakers iam getting howling sound plz helo me.
Bluetooth module aur amplifier module k bich me dc to dc isolator lagao noise chale jayega...... Common ground supply k wajha se wo nose aaraha hai
Sir , I bought lm3886 sterio board from bagood but as soon as I hook it up it blew up and one of the two ic burst within half a second . I used 24 0 24 dual transformer what could be the reason ?
Sorry to hear
@@WhatIThink work fine with 24 - 0 -24 replace ic and try again or board is made wrong .
Nice
Bhai ise 12v max kitne ampere or minimum ki Ampere ki supply deni hogi?
How can we attach two pam ic for 4 channels, make one video on this with clear wiring connections
phli baat k wo subwoofer nhi hain..or na hi wo boofers hain..wo pure woofer stereo speakers hain ...but apka knowledge great ha...bss ya aik correction thi jo socha k kr do..
Sir Maine bhi ye bord parches Kiya tha but ye 4om ke speaker ko nahi Chala pa raha tha lagbhag 30% volume ke baad bord band ho ja raha tha ky problem ho sakti hai ?? please reply
Sir can I use this amplifier in car with
6 1/2 inch speaker's
Can I use 5 w 2 speaker in this module
I used it but in battery & a 1000uf capacitor it doesn't creat noise
Sir ye car me laga shkte hai kya 4 speaker laga kr
Sir isko kitna ampere current tk operate kr skte hain???
Bhai iss module se treble jyada aata hai kya
Plz described the power supply for bt module
Sir mere Spekar connect hote he 2 second k lie awaj ate h fir band ho jata h. Fir reconnect hone pe yahe hota h kya problem ho sakte h??????
Sir app ny simple bass treble kit duoble lgany k bary me bola tha plzz bo video jaldi upload kren sir plzz
I am making...
5watt/5watt ka2 subwoofer use kar kate hai kya sir
Maine bhi same configuration me Bluetooth speaker banaya tha (10 watt wale chote speakers ke sath) aur power ke liye buck converter use kiya tha 4x18650 (3.7v, around 8000mah capacity) battery k sath but jaise he bass notes aata tha mera speakers k ek fattttt ka noise aata tha aur system restart ho jata tha... aur fir kuch time bad amp he udd gaya
Input voltage jyada rahi hogi ya fir load 4 ohm se kam ho gaya hogi
can i use 24v capacitor?
Sir I am using 4 ohm 20 watt speaker at 10 volts but clipping noise is coming please Help
I have purchased this one plz solve the noise problem
Dil se aasirvad, Sir mere pas 8610 ke do board hai ek ka meine bluetooth vala box banya hai isme bluetooth canceled/disconnect ki avaj bhot tej ati hai bluetooth module ke volume ka asr nhi hota kya input me algse volume lgasktahu aur keval 4 tweeter lagake Philips 8000b ke sath parallel chla saktahu
bluetooth module connect/disconnect ki awaj kam nahi ho payegi kyki wo software se load hoti hai. module aur amp ke beech me volume control laga sakte hain.
can this amplify a 40 khz sine wave coming from function generator?
Yes
aur 4700uf 25 v ka capacitor diode ke sath solding kardo, jo rectifying diode, ic ke aage se connect karna hai, dekhna performance beter milega
Sir can u make video on XA9533 audio amplifier ic