Configure Cisco Access Point using GUI Standalone/Autonomous with WPAv2 Authentication Key

#Configure_Cisco_AP #Standalone_GUI #IT_Support_People
IT Support People Facebook Page:
/ it_support-peopledeskt...
Link for Other Related Videos:
Configuring Cisco Router to Access Internet through ISP Home router:
• Connect Cisco Router ...
Configure VLAN | Allow VLANs to Access Internet
• Configure VLAN | Allow...
In this video I've shown step by step process How to Configure Cisco AIRONET 3602i Autonomous/Standalone Access Point using GUI with WPAv2 Authentication Key. I've divided the whole process into two parts which are given below:
Part 1: Accessing Cisco Aironet Access Point GUI Web Interface
• Console the Access Point with Putty (default user name and Password: Cisco)
• Resetting to factory Default Settings Using the MODE Button
• Check IP status and Assign a static IP to BVI1 interface with same subnet mask
• Go to Web Browser and type BVI1 interface IP address (keep user name blank and default Password: Cisco)
Part 2: Configuring Aironet Access Point with WPAv2 Authentication in GUI
1. In Easy Setup
Under Network Configuration
--Edit AP hostname, Static IP, Subnet mask and Default Gateway
Under In Radio Configuration
--Create SSID name WLAN_New under Radio 2.4GHz and select Broadcast SSID in Beacon
2. Apply Encryption Modes to AES CCMP
3. Enable WPAv2 and apply WPA Pre-shared Key: to SSID
4. Enable Wireless Radio Interface (Radio0-802.11N2.4GHz/ Radio1-802.11N5GHz) UP
5. Save the configuration
6. Finally check the SSID Wi-Fi connection, Security Key, IP address and browsing through internet
Cover Topic:
How to configure Cisco AP,
How to Configure Standalone Cisco Access Point,
Configure Cisco AIRONET 3602i Autonomous/Standalone Access Point using GUI,
How to Configure Cisco Standalone/Autonomous Access Point using GUI,
Cisco access point configuration step by step GUI,
How to configure standalone Cisco access point from GUI,
How to Configure a Cisco Wireless Access-Point (AP) from GUI,
How to configure standalone Cisco access point from GUI,
WPAv2 Authentication Key, Encryption AES CCMP,
Cisco AP Wireless Radio Interface Radio0-802.11N2.4GHz/ Radio1-802.11N5GHz,
Create Cisco AP SSID GUI, Enable WPAv2 and WPA Pre-shared Key,
cisco 3602i standalone configuration,
Resetting Cisco AP to factory Default Settings Using the MODE Button,
Cisco IOS Configuration Guide for Autonomous Aironet,
cisco autonomous ap configuration example,
how to access cisco ap web interface,
cisco ios configuration guide for autonomous aironet access points,
Cisco Autonomous Wireless Network - Home style configuration,
Configuring the Access Point for the First Time,
SSID on Autonomous AP Configuration Example,
Cisco Autonomous AP - Initial Setup & Open SSID Creation,
Autonomous AP - Initial Setup & Open SSID Creation,
Using the Web-Browser Interface Cisco Aironet 3600 Series,
SSID on Autonomous AP Configuration Example - Cisco,
how to access cisco ap web interface,
how to configure cisco access point without controller,
How do I assign an IP address to a Cisco access point,
How do I access my Cisco wireless access point,
how to configure cisco wireless access point via console,

[@Aarasastudio]

Your videos are highly appreciable as it is live in physical cisco devices, very useful and highly recommended for cisco learners. Waiting for all complete series. Thank You.

[@itsupportpeople219]

Thanks for watching

[@ARSINDIANVLOGGER]

Nice shearing dear friend 👍

[@stephensugandh9035]

Masood bhai you are very clear in what ever you show , and explain. . . I really appreciate it. . . Thank you very much, please keep up you good work. . .

[@md.mahtabuddin3979]

Good one and very useful for the IT people like me.

[@itsupportpeople219]

Thanks for watching

[@sabretd19]

Brilliant!!! Easy to follow Instruction... 2.4 & 5G working before video conclusion...Thank You

[@itsupportpeople219]

Thank for watching

[@shiabkhan6680]

Proud of you my friend. Searching some video on cisco air ap on youtube and suddenly it pops up to my screen.

[@edenorganics6476]

i've really gathered much here, thanks

[@MrEDGE1984]

I appreciate you ground work, most people feel expertise in advance thisgs but they lack basic understanding of networking. Ur efforts are worthy of appreciations.. plz upload more such videos.

[@itsupportpeople219]

Thanks for watching...

[@onrizestar7062]

One of the best video for Cisco AP Really awesome... Thanks for making this video

[@Lyriks_]

I just discovered your channel ! You're a gem, keep doing what you do !

[@itsupportpeople219]

Thanks for watching

[@roshanmutha2329]

You explained so nicely man. You showed router and switch physically to understand better. Thankyou. Please teach us more

[@rider275]

I really enjoyed this video. I have a home lab but no wireless access points. Your video has helped explain how I can add an AP to my lab. Thank you!

[@chimsopheak-pv]

Wow, it's the best tutorail. You have what I finding. Keep going on brother.

[@Hoscorp]

Congratulations, your channel has grow up, very usefull vids. Keep it up. This vid and the reset one i will do.
Thanks for sharing.

[@fred2009ification]

Cool video, man. Keep up the good job.

[@wildcurve]

Thank you bro for the information

[@grahammccann8554]

Thank you for taking the time to make this video. It was very informative.

[@abhinavsingh9957]

Thanks for Information 🔥

[@itsupportpeople219]

Thanks for watching

[@luisfelipecosta9664]

Thank's , from Berazil.

[@asifmehmood123]

Thanks for recording this video. This video is very helpful. Much appricated

[@itsupportpeople219]

Thanks for watching...

[@k.j.fatema7865]

Excellent content...very informative and easy to understand...keep it up

[@itsupportpeople219]

Thanks for watching

[@mohamedabdelkader8846]

thanks for the video :)
I have a quick question , can we use power adapter instead of POE injector in case my switch has no POE ?

[@mhabibtmc6399]

you well explained i would like to say thank you for this. Appreciated !!!!!

[@jeffersoncafegarcia8215]

Good video 📸😊

[@itsupportpeople219]

Thanks for watching

[@NewsBroadcasting]

Good video , is it possible to use AIR-CAP27021-A-K9 as standalone?

[@chiarenwar7139]

Have same question ....

[@martinsenechal5379]

Great video,realy helpfull.
Can you tell us how to set both 2.4 and 5ghz with the same ssid
Thanks

[@itsupportpeople219]

Thanks for watching.. You can add 5GHz radio interface similarly like how I did for 2.4 GHz

[@hoanggeneral]

@IT Support People,
I was able to get all the way and completed the set the BVI to a static IP (manual). However, when I tried to access the GUI interface in the web browser, the base just won't load.
Any clue on how to over come this?

[@TypeOneGuy03]

same

[@TrungTuyenLam]

Do you know? The GUI interface is just used for the standalone IOS version of this Cisco AP.

[@rasailiofficial9885]

Ok thank for infomisson sir

[@itsupportpeople219]

Thanks for watching

[@mohammadshahfaisal427]

Suppose I don't have a console cable, can i configure direct access point

[@omg2026]

Thank you sir for another great video!

[@itsupportpeople219]

Thanks for watching

[@Jagarm]

Thanks for the great video. Thanks to you, I got it all setup, but the speed is slower than my router

[@itsupportpeople219]

Thanks for watching...

[@gugulethumoyo6284]

This is very helpful. Its practical

[@ibrahimsaadansary9840]

Vaia you are too good. i am also working as system support engineer. if possible please make real life virtualization training video. very much needed. and one request please don't lower your quality when you will become famous. may Allah bless you.

[@user-tb4hk5nq5c]

Thanks for your hard work.
Please keep making videos. It is very useful.
Forgive me, but I want to make a couple of comments:
1-Could you balance the sound in your videos? You have to constantly adjust louder\quieter.
2-Could you try to remove the noise?
3-Sometimes it seems like the video is a little too long.

[@itsupportpeople219]

Thanks for watching... Lot appreciated your suggestions

[@amirahmed1404]

Very good explanation. Thanks you.

[@himanshuyadav3380]

Bhai you have made awesome video can you make video on AP light version which will configure by wlc.

[@itsupportpeople219]

Thanks for watching

[@leaguebdd2053]

It really helps a lot about the Cisco AP !

[@itsupportpeople219]

Thanks for watching

[@rodrigosebben1084]

Thank you so much! this video help me to configure the ap.

[@villagedotvibes]

Thank you so much for this video. Your content is importent for real life support. Please make a video with OSPF and EIGRP routing configuration

[@itsupportpeople219]

Thanks for watching

[@pramilasingh2726]

explained everything in detail

[@itsupportpeople219]

Thanks for watching

[@phantran3718]

We have two band 2.4 and 5 on the Aironet. Can you make a clip how can we make them online with one SSID only. I have two aironet, is it possible to run seamless SSID in autonomous.

[@rashiniperera7000]

thank you so much for this content

[@user-et1no4cr3g]

thank you for your video it helps me a lot

[@ajmusicpak3238]

nice yaar

[@LoveHWH]

Hello Bro, Just got a question. If I have another APs, so all the configurations will be the same in this case? Thanks

[@PatrickGuerrisi]

when I try to make my ssid I get the following "encryption already exists in interface, enable vlan"

[@mauricionava1976]

Thanks for the video!!

[@MahananGogoi]

Great tutorial. Thank you!

[@itsupportpeople219]

Thanks for watching...

[@lkdipeolu]

Very Good. I love it. Do you have the lightweight version?

[@sherrillboyce7189]

Thanks! For home network, do you recommend a CISCO ASA FW to CISCO Router to Cisco Switch to VLANs for Cisco Aironet and other devices?

[@itsupportpeople219]

Thanks for watching...I reckon Cisco ASA 5505 Firewall is well enough for home network

[@makmalbalouch7810]

Nice

[@itsupportpeople219]

Thanks for watching

[@yourictmyedu5783]

Thanks

[@narender1199]

So Super Sir ji

[@tanmaymukherjee502]

Excellent

[@itsupportpeople219]

Thanks for watching

[@sadamsta5302]

Good job 👍

[@MuhammadAli-od7hd]

Oooo lovely

[@itsupportpeople219]

Thanks for watching

[@mimegajet6346]

nice content

[@MineGamer153]

Hello, I want to ask what type of rollover cable you are using. I just bought USB-RJ45 type but I cannot connect to my LAp1142n. With WLC it works just fine. I tried different baudrate but still not working.. Thanks for any answers

[@SuburbanSwadh]

Very nice 👍👌

[@itsupportpeople219]

Thanks for watching

[@owaisraja5325]

Very nice

[@KHANQTR81]

i am trying to download ios image for " Cisco Aironet 1140 Series Access Point"
but can't. will u help me please. thanks

[@richardm7502]

Thanks for this video it's for sure helpful,, and how can I configure my Cisco AP has this version AP3G2-K9W8-M?

[@garyhedberg4318]

Will this process work with a Cisco Aironet 2602I-A-K9? I don't have PoIP but I do have an external 48vdc power supply. Would there be a firmware update that needs to be applied first? I'm just a home user. Overkill probably but I picked up 75 of these access points at a very reasonable price.

[@appelwoin76]

Have you confiured a dhcp server for the client IP`s and where ? When I configure 6 Standalone APs, can i configure the same SSID on every AP`?

[@wajahatullah3626]

Hi Masood, I've configured the Cisco AIR-LAP1042N-N-K9 through static IP and also added the radio 2.4 & 5 GHz & enabled in network interface but still I haven't found the Wlan in my WIFI list. The AP is showing green light instead of blue, it's mean that no one is connected through this AP. Can you please tell me what to do to make ensure that WIFI is working.?

[@itsupportpeople219]

Thanks for watching...
Make sure you selected the option "Broadcast SSID in Beacon" in the Radio Configuration area.
You can try under SSID Configuration "mbssid guest-mode" instead of "guest-mode"
Thanks

[@PiotrWisniewski-cy2sd]

Hi. Is it possible to use Cisco 9105 awx in home instalation?
I've got 3 pcs of that AP, and i cannot do anything with that:(
Thanks for your answer.

[@PatrickGuerrisi]

Man I set this up ages and I am tryin gto disable it. When get into the
Network Interfaces: Radio1-802.11AC5GHz Settings settings. I click disable next to ( enable radio ) and it just goes back to enable automatically'? I cannot disable it

[@danicanilbertvlog8042]

Good you're content

[@itsupportpeople219]

Thanks for watching

[@rkbusiness5952]

Very nice beautiful😍 😊 ❤

[@Adnankhan-rx6xo]

Well done

[@itsupportpeople219]

Thanks for watching

[@taimoorsaleem8080]

Dear please tell me how to configure AIR-CAP2702l-E-K9 cisco access point setting. I try but it's configuration not display.

[@dennisdoubek4329]

I have a problem, every time I want to access my access point "ap:" is displayed in Putty, but in your video "ap.home.>" every command I enter is played with unknown CMD. what am I doing wrong?

[@SamMehnaz]

I have the same issue! Did you figure it out?

[@MuhammadAli-rf2jo]

goood

[@itsupportpeople219]

Thanks for watching

[@ironmen9983]

Hi, could you please have a video for Cisco VOIP configurations. Thanks

[@davidnagapn6075]

Great videos, I am looking for the autonomous firmware for a AIr-CAP3702i-A-K9. If no one has it, do you know where I can get it? I can't download from Cisco.

[@Vandelroy1]

thank you for your video! But it does not work for me, I check my config with your multiple times, but it is the same. If I try to connect with my Windows 10 Client, I get directly the message that no connection is possible with the network, also I get no field to type the password. If i change to open Wifi with no cipher the connection works. Can you help me?

[@PPL9420]

Plz tell for wlc and Ap different network in possible

[@Tommy-oj4hd]

I only see: GigabitEthernet0 interface, can't see anything else like Radio or BVI1. I am running: "C3500 Software (AP3G1-RCVK9W8-M)" any ideas?

[@silaskalonzoke3038]

Nyc 🥰

[@ahmetgure1506]

Thanks for video,
When i press apply 19:21 it says; *WPA requires 'network eap' or 'open authentication' with eap or 'open authentication' with 'wpa pre-shared key'.
How can i solve this problem?

[@monkeybluesMMA]

do we need a switch to enable and connect to a cisco access point?

[@RajaRaja-sc2xb]

Thank you sir

[@Fun--knowledge]

good and samble

[@argenisvalero8461]

Buenas amigo una consulta tengo este asepoint cisco aironet 1252ag ak9 nesecito orientacion ya que me llego uno y quiero saber si la consola de trabajo es la misama para el reseteo que sotwere nesecito y si el proceso es el mismo en este modelo con referencia del video publicado

[@ervindarya]

would this work with Cisco Aironet 2702I AIR-AP2702I-UXK9 IEEE 802.11ac 1.32 Gbps Wireless Access Point also?

[@pernord26]

can you do a video with Cisco Mobility Express

[@leading4Him]

Skip to 4:00 if you actually came here to see how to setup the AP.

[@animalsvideosalltypes.6005]

good

[@shiva___pavi]

bro thank you so much

[@itsupportpeople219]

Thanks for watching

[@python1058]

What did you connect the console to

[@Heena-Khan-001]

Need autonomous firmware for cisco AIR-LAP1042N-N-K9, can't find it anywhere, help me plz

[@itsupportpeople219]

Thanks for watching... Service period for 1040 series AP has already been expired that's why there is no firmware available for this model.

[@hamedashrafi1]

@@itsupportpeople219 i have same problem how i can use this acces point ?do you have that file in your archive?

[@Chanchalsohan01963249691]

how to upgrade firmware/ios in cisco access point more than one at a time using tftp server??

[@riyas2khan]

hi bro, can we setup guest access with limited time access ?

[@loucarossignol901]

any reason nothing shows up when i select the com port on putty?

[@laxmanpatil4079]

can you share me firmware link for cisco WLC of 2504 not able to add AP in controller

[@fahimuddinsafi9958]

Hi Sir,
Can access the AP from Browser cannot make any changes to it through GUI says 404 not found
any solution please
thank you,

[@MrMARIF786]

Hello Dear i hv cisco air ap2802i-e-l9c there is wireless option setting is disable in web console i can't add multiple Ap in on console ...plz u can help me about this there is some command in CLI mode to activate wireless setting. if u more information i can send u screenshot. thank u

[@sebghatullahkarimi2075]

Hi!
how to configure cisco 3502i a or e access point router

[@SatpalSohal]

Can you provide download link to autonomous firmware for Cisco Access point 2600 series

[@itsupportpeople219]

Thanks for watching... I have image for Cisco standalone 3602i AP. If you need it I can give you the link.

[@SatpalSohal]

@@itsupportpeople219 Do you whether it will work with 2600i series.

[@SatpalSohal]

@@itsupportpeople219 I went to Cisco website and the file names are same for autonomous firmware for 2600 & 3600 series. Can you please take a look and also send a download link to the file you have.

[@opendebate]

Please make a video to upgrade the firmware from GUI