Volvo 940 Rear Brake Replacement - Increase Stopping Power (740, 960)
Vložit
- čas přidán 7. 09. 2024
- ►Shop the Products used:
Brake kit: hubs.ly/H0cWv_x0
Caliper: hubs.ly/H0cWvLR0
SUBSCRIBE: hubs.ly/H0cDnfN0
We've finally got a brick in the shop this week, and this '93 Volvo 940 is getting a full brake replacement at all four corners. Mike Rivera will walk you through the steps for caliper, rotor, line, and pad replacement.
How to bleed your brakes: hubs.ly/H0cWvP50
Get free parts from FCP Euro:
www.fcpeuro.co...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/
2:52 , Thats why you are supposed to release the e-brake tension adjuster in the center console first, before you remove the rotor.
It might be because of the edge on the inside of the brake disk
You are the comment I needed to hear from. I was searching for this answer.
Excellent video. I believe the anti-rattle clip was placed in upside down. For all of your time and effort, thank you very much.
You put the clip in the wrong way, please inform people of this so that they don't do it wrong either. Just google up some images and you will see.
Came to the comments to see if anybody had noticed. It's been 5 years. They should at least pin this comment. I wonder how many people they screwed up with this video.
The most neglected parts of most cars, rear brakes, so refreshing to see some serious investment on this car.
Before installing brake shoes on these Volvos, Make sure that you loosen the adjuster at the level in the interior (behind the ash tray in the back) almost all the way. Not only will this make installing easier, but if the level adjuster is too tight, you will not be able to get a good braking force on both wheels.. (been there, done that..)
I think the metal clip is upside down at 9:25. Otherwise great video!
By gosh it is upside down! Oops! lol
thought the clips go either way look the same, top or bottom to me i service my brakes every year on 22 years of ownership
of my 940 estate
Thanks very much. I've got to do just this in my '92 940 this week...
Great video. Thank you. I have a 1987 760 turbo.
Great step-by-step instructional video. Great explanations to a explain the steps. Thank you.
Super helpful. Thank you.
Volvos should be SAE, eh? So 9/16 should be correct. Just found out last night if you find a way to depress the brake pedal roughly 1/2'', it shuts off any leakage from lines. Cool eh?
I noticed the e-brake shoes were not adjusted or the rotor not even turned to check the shoes drum clearance.
Showhow to replace allthe bushing in the tyrailing arms & the Torque rod..
Would these instructions also apply to a 960? I need to install new shoes for my parking/emergency brake. It's adjusted all the way.
Can u help me, I have a 940 base volvo wagon, the mechanic didn't put the preheat hose back on, never said anything about the air box thermostat etc, I think they should have just replaced the preheat hose, without it their is a lot of extra hot air in the engine compartment, also the holes are just open, if the thermostat in the air box is confused due to no preheat hose what happens they didn't even mention the air box thermostat so I don't know if it works now, also they never cleaned my MAF, it was corroded at connections they didn't know how to check the obd codes so I figured it out and cleaned the MAF sensor which completely has improved my idle which was too high all the time esp in park or neutral . Thank you
новые оригинальные запчасти,это есть хорошо
Do the 13mm bolts to hold the new caliper in place need to be new (not previously used) bolts? Thank you, Martin.
v8pilot They can be reused but check for rust or stripping before you do so.
FCP Euro Thank you.
Interesting: the bolts that hold the calipers on my '90 Volvo are 17 mm. Goes to my theory that Volvo knew for years they were going to sell their car division, and started compromising the design to better fit the way other cars were made.
Is this the same on a 95 volvo 940 base wagon
what are you spraying at 3:16?
Nickey Fynn It was this stuff right here: www.fcpeuro.com/products/crc-brakleen-brake-cleaner-14-oz-aerosol-can-05084
you didnt copper grease anything
No we didn't, we used the supplied grease on the back of the pads and on the contact points.
FCP Euro you should never use the supplied grease
+1. .. The supplied caliper lubrication is by ATE, the brake system manufacturer. .. I've used the ATE caliper lube for 30 years on our MY98 911 C2S Carerra, MY95 E320 Coupe, MY79 VW Beetle Cabriolet and an MY07 Volkswagen GTI. The ATE lube is all good.
Your gloves looks really big and useless
Thank you so much for this video
You are so welcome!