Video není dostupné.
Omlouváme se.
P0301 Misfire AND Lean P0171 Diagnose and Fix TOYOTA CAMRY√ Fix it Angel
Vložit
- čas přidán 3. 11. 2020
- Repair Manuals: shrsl.com/3zwnv sovrn.co/amfaf3n Fix it Angel EBAY STORE: ebay.us/OE6UsK repair smith fxo.co/1284793/fixitangel THANK YOU ALL FOR WATCHING MY VIDEO. This video is NOT sponsored. If you would like to support this channel. These links are my affiliate links which means if you buy something I will receive a small commission. Thank you for your support. God Bless
www.amazon.com/shop/fixitangel www.getsomevegas.com/home
1997 1998 1999 2000 2001 2002 Toyota Camry 4 cylinder 2.2L Engine
Replaced the Oxygen sensor before the catalytic converter.
The codes P0301 and P0171 was present before oxygen sensor replacement. After replacement, the same code came up.
P0301 Misfire at cylinder #1. P0171 Lean condition
Removed #1 fuel injector and tested the resistance. It had high resistance and determined that it was bad.
Replaced the injector and it fixed the problem.
O2 sensor socket set sovrn.co/1bnt1k1 amzn.to/3oVWUhm
anti seize grease sovrn.co/p3l7jxy amzn.to/3vm5URR
Pliers Set sovrn.co/u1eq9zu amzn.to/3ylRTFM
30mm socket sovrn.co/mmolf3k amzn.to/32draKF
Pry Bar set bit.ly/3wRZonf amzn.to/3EYORc2
Ratcheting Wrench set sovrn.co/13dv34b amzn.to/3wrtwUP
fuel injector sovrn.co/ub0k75x amzn.to/38hI5SH
digital volt ohm meter sovrn.co/mtww9hl amzn.to/3kP0bOs
valve cover gasket sovrn.co/k3nev0n amzn.to/3oYe7Xa
Toyota FIPG sealant sovrn.co/51n7gm3 amzn.to/3rYep3t
PCV valve amzn.to/3jVvtAt bit.ly/3KrFLG2
ebay.us/p7q2BY bit.ly/3KOIWrN
I accept Fan Mail!!
Send to:
Angel Fernandez
PO Box 96711
Las Vegas, NV 89193-6711
My Facebook page, Fix it Angel.
Click on LINK / fixitangel328
Please donate here if this video was helpful
Click LINK www.paypal.me/FixItAngel
VENMO @Fixitangel-38
i accept BITCOIN 3FpDghxbWBTSvmdiDXivFdrrx4fCYurmFC
Purchase any of my apparel and a portion of my monthly earnings will go to Catholic Charities here in Las Vegas
Click on LINK www.cafepress.com/fixitangel
You can also follow me in:
Twitter / fixitangel
Instagram / fixitangel
This channel shows how i fix and repair my family and friends cars. I show mostly import cars like Honda's and Toyota's. But I also show repairs on Domestic and European cars. All links in the description are affiliate links. if you would like to support this channel. purchase any of the product links. i get a little commission from each purchase. thank you
I love watching these higher mileage honda/toyota vehicle repair videos which only need minor repairs to keep them going well into 200k+ mileages, thanks!
Always the best in making auto repair videos. Thanks Angel.
I went to UTI back in 1983 for refrigeration and A/C ! Great school ! 👍
Your kids are hilarious and cute. I admire how hard you work to support your family. Cheers Angel
I love these Ingine Sound and your job
currently I was a lube technician her in KSA, watching your videos makes me how to improve my knowledge,.. thank you sir. 👨🔧👨🔧
I always watch and love your videos. From Argentina. Spare parts are super expensive here specially OEM. I have to be 100% sure before changing and O2 sensor, test resistance and if its getting power, if it's ok keep looking for the problem. I am not a mechanic. I am just an opinionator as most of the people who comment videos here. Thanks for sharing your knowledge. Good way to find out it was a bad inyector.
Happy birthday leyzel. My birthdday is tomorow guys
wonderful family, God bless you..!
Thank you for the sticker! 🙏🙌🏽
Great video as always Angel . Just for my curiosity, I wish you would had show the final fuel trim levels. God Bless you friend.
Ditto, would have liked to see that as well.
Hi from Hellas ! I wish the best for all !
Solid chelu, keep the vids coming 🤙 and honestly yes i noticed that u didn't put the hose on. For some reason i spotted that empty space where the hose was suppose to be, even before i saw the question about the the hose.
Nice work bro I wish I live next door to u god bless u and ur family bro
Thank you for doing a very nice job with the original parts, hope you can resell the O2 Sensor, I am not sure if you mentioned a noticeable misfire, great video.
Boldog születésnapot!
15:42 satisfying sound of snapping coils onto spark plugs
not coils, high tension leads.
Or Spark Plug Wires
Good video brother thank you
Job well done 👍👍👍👍
very good job !
I watch your vibeos all the time. I'm junior mechanic
Good job 👍
i welded my exhaust yesterday and *burned my car down* ...
WE CAN REBUILD!
today i am cleaning the whole interior, ripping the burned stuff out (whole passager side and center console) and i am rewiring a bunch of stuff.
if i could give some advice is to hang a smoke detector from the center mirror and to always wear earplug while welding because i got a burning amber down my ear.
حفظكم الله و رعاكم
That old 5sfe top end is in excellent condition 👍 this engine is prone to sludge normaly.
أحب العمل الذي تقوم به 🤗
Nicely done, by the book.....
😁👍🏼 good job 👏
Good morning from Alaska
Good job
Thank you.
Hi 👋 my friend .. thank you for your time, efforts, kindness to show us the best way to fix mechanics.. what is the best procedures to maintenance GDI engine on 40K miles Kia sorento 2017 .. What to do to keep it works perfectly ..my best wishes REGARDS for you and your family
hello brother, to maintain the car, just follow the car maintenance record book the manufacturer provides. thank you. God Bless you and the family
I did notice you forget to connect the hose Angel... Happy Birthday to Leyzel, Nice family God Bless you Guys 🎂🎉🎊🎈👋
Thank you for watching. Leiyzel says thank you. God Bless you and the family.
Toyota makes their own rubber grease. It’s soap based and good to use on those o rings to help slide in without binding
Sir tnx for you're info. I learned more ... Videos.. shout out mo Naman ako sa nxt video mo... Supportahan m Rin ako pls.. tnx
Good
Saludos amigo
More videos plz. Hello from Russia! Peace!
Hi from dubai. Thanks for great information. What scanner . Isit a good scanner
U do good work Angel... nice job...i personally hate to work on Toyotas, too much - 'eng ong eng' hahaha
thank you Chuck. everybody has their own preference of cars. have a nice day.
Happy birthday leyzel.
HAPPy HaPPY BIRTHDay to both of you,greetings fr manila,GODBLeSS
Salamat Raymundo, God Bless you and the family
Great diagnosis and repair 👍OEM fuel injector didn't come with rubber seals dam times are changing
thank you brother. it didn't come with a grommet that goes on the base of the injector. have a nice day.
That really gets me specially when you go to the dealer and they dont even ask or tell you if you need or want those parts...
Good good 👍🤙🤙👏
hi friend
i have same problem lean cnond fuel trim lt at -25 and i checked every thing but still have the same problem
notice: fuel injectors ohm between 15.5 to 16 could be this cause the lean condition
thank u
Happy birthday
I want to ask, is 2008sienna c1249 related to my changed led brake lights?
What scan tool do you use and where did you buy it from. Im in Fiji islands i need one for OBD1 AND OBD2
When one goes out the rest follows i know its expensive but if keeping the car worth doing it that can be a job being located in the back versus the front
Thanks good information 👌👌👌👍👍👍🇮🇳🇮🇳
Thank you Manish
Nice great diagnosis but if you didn't get a code will you solve it??
In nissan for cars exported to gulf countries there is no live data like short and long fuel trim tried autel maxidas, md805, autel mk808bt no way then checked on Ford car and I got pid long and short trim also I got onboard diagnosis which is not supported by nissan really confused also tried elm 327 not showing live data short and long trim and no codes in my car and rpm goes down to 450 then return back to 700 on idle or stop once car warmed up its maxima 2013
Changed spark plugs, 2 coils, cleaned injectors with ultrasonic while pulsing
Cleaned throttle body
And air mass
But once i disconnect air mass it runs OK no fluctuations so does that mean airmass is bad???
i love you
El canry me llena el ojo homy!
happy birthday leyzel.
thank you tomtom. have a nice day
No fuel pressure drop test before taking it apart ?
Hi, can i ask about the water temp sensor under the radiator on my camry 2.2 2000, the harness has no voltage coming from it, positive only reads from 0.1 to 0.3 but negative reads 12v those are while ignition position is on. Is this normal? Because the other green coolant sensor near the ignition coil reads 5v when ignition position is on. And i think the engine is always running rich. And also radiator fans are immediately turned on when ignition is on.
نحن نحبك 🇾🇪🇾🇪🇾🇪🇾🇪🇾🇪
ممتاز
Hey fix it angel! How come your logo has a wrench 18mm but not 10mm socket?
The structure of the block looks very gothic with those supports along the body. Looks like something you'd find in the citadel in HL2.
I owned a 97 camry way back; did not really like that engine; much happier with the 1.8L 1zz in my 05 matrix 250k and counting
By the way what's the coast of your scanner tool 3000$? Just guessing
Why did you put that fipg sealant on those spots is their specific reason are they potential leak spots thanks in advance. Happy birthday to your daughter as well
Sometimes they could leak ‘cause it’s a curved angle. Just apply some sealant on the corners of the curve surface area.
I watching TV your fixing everyday how do get the program on the phone do I have to down load the program I fix my car I don't know how many vfoot pound I just tight it or have to Google all the time
👌👍🏻
Do they have a scan tool that can check the resistance of each individual injector
i don't think so. if they did, every mechanic would have it. that would be so much easier.
👍
Happy birthday leyzel ask daddy for new car good luck hun
thank you Danny!! a new used car lol
Do it right the 1st time👍
Hello Angel I have a quick consult to you , I own a 1998 Vamry that when is heated the idle starts to fail and the engine stops when I got into a stop light, some one told that could be the EGR valve but I do not know how to diagnostic that , the OBD gives me no codes =( Do you know how to fix that ?
hello jorasave, it could be many other problems. what have you done to it, as in repairs? i need to know what you did to try to fix the problem.
I would clean the throttle body, mass air flow sensor, replace fuel filter if applicable and let us know if you have access to live data so we can help you diagnose the problem, Also it will help to know if it is a 4 or 6cyl and how many miles it has....
For my experience.. if like that im disconnect the negative terminal in 30 seconds or more .. automaticaly oxygen sensor will be reset..
I got the Po712 running to rich? Help
Pls help, there are no positive voltage signal coming from water temp harness camry 2.2 2000
No power to it then is broken.
Bet one of the thumbs down was scotty kilmer 😜. You were showing a Toyota having issues and that never happens!
I changed the sensor. But I get code p0325. Its a 2000 Honda accord. What do you think IT could be
What other repairs you did to it?
@@FixItAngel I changed the pressure sensor oil
Привет я из KZ твои видео нравится тебе жирны лайк
привет брат, спасибо за просмотр. Приятно иметь фаната в kz kazakhstan. хорошего дня.
So the Original o2 sensor was fine?
The lean might cuase by the Air Fuel Sensor or the Map sensor. I replace the AF Senser the problem still exist. I replace anothe 02 Sensor in the bottom, the problem still exist. Damn. I wast alot time and money. I gave up, my wife took to a mechanic. He replace a map sense then it works likke a charm. My lesson is to replace the cheaper part first like the map sensor. He has tow code one is lean and the other one is misfire. I am not a mechanic at all. I hope it help. My camy is a 2003 with p0171, lean. Those Auto parst store guy just sell u the part such o2 senser, and u can't even return. I wasted money and headaache.
@@jetd6764
Clean the IAC sensor on the intake hose. That should fix it. If not replace it. That is what PO171 is pointing to.
Hello sir, I need help.
I have a 2006 Toyota Camry base model with 2.4l. I have p301 and p171 errors. I changed spark plugs, ignition coils, MAF sensor, valve cover gasket. PCV valve and hose. I don't know what else I need to change.I checked the air intake it looks fine. This made me so tired. I need your help with this.
hi, change the fuel injector in cylinder #1.
@@FixItAngel thank you very much for your fast response. I will be changing that. If I can make it work, I will be updating this message thank you sir.
@@Butwhoan welcome brother. problem with your car is the same thing happened to the car in this video.
@@FixItAngel Hello, I changed 4 of the injectors, I still have the problem. I will be driving 1-2 days if the engine lights would go away. If not, I am planning to change the o2 sensor, air intake cleaner on the front with the hose. I will be updating this topic. I know that a lot of people are looking for the answer. Thank you for your service.
@@FixItAngel hello, I drove 50 miles and engine light is gone. I can still sense that sometimes its getting more air. I will be changing manifold gasket seals. I solved my problem thank you very much!
lol he said #crockroach again xD 6:01
Hello guys. Just a quick clarification. Torque for valve cover for 92-96 is 13 lbs. 97-01 is 33 lbs.
thank you brother, i need to change the years on my video description. have a nice day.
@@FixItAngel hey any time bro! Love your videos man! Keep em’ coming !!
What is the easiest car to fix and Maintain? Toyota or Mazda?
hi, from my experience as a used car tech when i was employed by a Toyota Dealership. The different cars i have repaired, Toyota's and Honda's are easier to maintain.
@@FixItAngel I definitely like Toyota’s. My Toyota Camry 06, always makes a noise I’m the morning when backing up downhill. It sounds like a rudder, can I send you a link or anything?
Si cambió un inyector limpie los demás, ahí lo vi muy mal
This is exactly what NOT to do when "fixing" a car. Simply firing the parts cannon because of a DTC and not diagnosing is the hack way of doing things. Poor customer now spent money on an unnecessary part.
Please just shut up when you dont have any ideas about fixing cars.
@@waldemar31293 😅👏
هل بإمكان ترجمه الكلام لل عربيه
5SFE!!!
Great engines
have mach oxygen sensor
Low mileage for a 5SFE
👍🇰🇿🛠🔧
First!
Egypt 2d
send it bro never lift!
First mistake u use copper anti
So there is nothing wrong with the oxygen sensor right, only the injector fail then there is no fuel and too much air intake cause the error system too lean.
No, the IAC needs cleaning/replacement. He's full of shit.
Happy Halloween everyone here good luck Donald trump, good luck john bayden God bless United States of America Jesus loves you i am from morocco have a good life for everyone here 💟💖💜💙
Sir I am interest your assistant please sir🙏🙏 I am from Bangladesh 🇧🇩🇧🇩 I am 6 months training automotive mechanics I am national certified
Find a job in India instead of asking a usa CZcamsr he's doing fine on his own
Good job