Blind Spot Sensor Calibration on a Hyundai | Check BSD System
Vložit
- čas přidán 13. 06. 2019
- scanner I use in this video: amzn.to/31ChIPi
In this video I show how to calibrate a Blind Spot Detection Sensor on a 2018 Hyundai Elantra after replacement using an autel scanner. Please like the video if it helped you out and subscribe so I can post more how to videos like this. - Jak na to + styl
I have 2020 Hyundai Elantra sel and having same problem. Dashboard warning light has triangle with exclamation point in it. Also car does self check and has diagram of car and pointing to rear sensor on dashboard. Took it to get it calibrated and warning light went off but came back on when drove car a few minutes. Right rear bumper has abrasion like a car just grazed the bumper but it's noticeable. Thanks for the video
Hello, do you know if most scanners sold on amazon are able to recalibrate the BSD system like yours did?
Thanks for the content.In Canada Kia wanted $1650.00ca for the rear passenger side sensor.I found one online and installed it myself.The body shop suggestion is a great tip.If i can clear the codes i can have the car certified here and start to drive it.2017 Kia Forte with less then11000Kms
Glad to help. These sensors are definitely overpriced from the dealer and there’s plenty used ones out there for a fraction of the price.
@@themodernmechanic428my daughter's 2020 Tucson value was backed into and cracked the RH blind spot module. My dealer wants $3300 to replace and calibrate it. Nothing else just the module! I asked if I was able to replace it with a used one and was told, no, it wouldn't work and had to be a new one. Do you know if the 2020 and newer models require a new one that has anything to do with the VIN number or are they replaced and calibrated the same way? I know I'll need to fine someone with an Altel MS606 or MS608 to do the calibration. Thank you for your time.
Do you have any idea about frequency band for front radar Hyundai Sonata limited 2016??
Thank you for a clear and simple video right to the point . Very helpful I have a kia at our shop that needs this exact service . We are always learning everyday .
Glad to help
I would like to by a scanner for at home use. What function do I need to look for when buying the scanner that will let me know whether or not it can calibrate BSD?
Hi good day wat scanner can I use to do the calibration is there a budget scanner I can use ? Can you please help me
great knowledgeable video - thanks for sharing
Am I BDS system went out on Friday And I was an accident in November and didn’t have issues but then all of a sudden it came on and started working yesterday for some reason didn’t do anything didn’t have them re-calibrate it and now I’m taking it to the dealership to have them re-calibrate it are they gonna be able to re-calibrate it even though it’s back on again
Great friend ! That’s just the same I need to do on my Mazda 6 2014, my old Autel scanner says the same “missing calibration” but mine has not that function, here in Mexico can get the Autel MX880 if you have some time some day to check specs about it I would aprecciate so much, I can’’t find info if this scanner has that function, thanks for sharing, regards.
Hi Oscar, i think you’re talking about the autel mx808. Not 880? you can actually contact autel straight from their website and verify the functions of that tablet before you purchase. I’m not an expert on all autel models so I don’t want to give you false information. Best of luck with your repair.
@@themodernmechanic428 Yes sorry mx808, thanks for your response, I will check directly with Autel, regards.
Can you do that on a 2019 jetta VW?
Thank you very much!
Do I clear blind spot error on dashboard after Installation of new blind spot radar
What name exactly for the scanner I can use it for 2014 Hyundai sonata to do same calibration
Is there a less expensive Autel Scanner System than the MS908S/Pro that will re-calibrate the "BDS" on my 2015 Hyundai Sonata? Thanks, DS
Did you find out anything?
Can bsd system stops a car from moving
Tanks bro!!!
Thanks, Singh
Could you please tell what soft do you use in this video?
Hi, I’m using an Autel scanner.
I replaced driver side mirror in my 28 teen sonata Now I get a triangle with the! Telling me to check BSD system what type of OB DE to do I need to get that has the capability to reset the system. A replacement mirror is blind spot detector capable is this common when you replace mirrors that you have to calibrate the mirror?
Replacing the mirror alone wouldn’t require a reset since it’s only an Indictator. The sensor is behind the rear bumper. It looks like maybe you installed the incorrect mirror. You probably installed one without the Blind Spot Detection. Make sure you got the correct mirror.
@@themodernmechanic428 has blind spot detection on mirror that's why it dont make sence. Talked to dealer and they said has to be reset.
Hello I have 2021 Hyundai sonata but tried calibrating it its saying software missmatch how can you help
Do you have a shop in Ontario Canada? Does anyone know where can i show my 2024 Hyundai Elantra with the same issue... Somebody bumped on my rear right bumper and now the rear parking sensor doesn't work the blind spot doesn't work.
Hi, I have a 2016 kia optima SXL Turbo and looking for desperate help!.
I replaced the whole panoramic sunroof assembly because it was broken (front windshield too) but after person Replaced it (SUNROOF ONLY), I had all these sensors turned on (right after used one was installed) CHECK ENGINE, AIR BAGS, LANE DEPARTURE, THE EXCLAMATION POINT ONE INSIDE A TRIANGLE, ABS, EPB, STEERING WITH EXCLAMATION POINT, PRE COLLISION, (CHECK SMART CRUISE CONTROL SYSTEM). Also, I have no back up camera or any camera working , nor speedometer or odometer, gas gauge or temp gauge working or blinker displayed when I put it on. Also no dome lights or mirror lights working. All this happened as soon as the guy was done with the sunroof replacement, Keep in mind the original front windshield was still on because it was going to be replaced the following day by someone else. Also, when it was broken, NO LIGHTS WERE ON AT ALL. So now the sunroof guy is blaming the Calibration on the front windshield but AGAIN, They all turned on when he replaced the sunroof (plus he couldnt get it to work and started pulling out fuses by steering). IDK What to do! He keeps saying the sunroof had nothing to do with the lights coming on...WILL RECALIBRATING IT TAKE CARE OF ALL THIS???
PLEASE HELP!
Hi, I have purchased the part and I need to know how much does that cost for calibration. I also need to know where can do that I live in Anaheim, California. could you help me?
Hi, I am located in Pomona. Search SoCal collision and parts in Pomona on Yelp. Call the number and I will give you a quote.
My car has the same problems. I resat but come back again and again. I think I need to change the also. How much do you charge if I change?
What scanner is it?
hey are you in Canada I need to have my calibration done my mechanic could not get my sensors to work.
ImTz Aspire sorry I’m in California
Hi where are you located? Im in San Diego, I have a mazda3 what I get that BSM message only after 5 min of driving, it works fine the first few minutes and it the same every time I start the car back up again
Hi I’m located in Pomona CA. was the car in an accident?
@@themodernmechanic428 yes the car was in an accident. bought it from iaai and now is fixed everything but that
Hi, I took my Hyundai to put on a hitch and the shop zip tied the trailer hitch wiring to the BSD module harness and the service BSD came on. I saw on CZcams thats a no, no. So I re routed the trailer wiring and zip tied them to the frame of the car, now I have to re calibrate the module. I called the shop and the said they don't have a tool to recalibrate the module to take it to the dealer, I don't want to give them the money to do something like that.
So I was looking for the MS908 but they are no longer available, do you think the MS906 do the job?
Brandon Perez yes the ms906 is able to calibrate the BSM.
Are you sure it needs calibrating? Simply zip tying or disconnecting the harness wouldn’t cause the module to need calibrating. Just verify that everything is plugged In before you spend the money
@@themodernmechanic428 Thank you for the quick response 👍 🙏.
@@themodernmechanic428 yes I have a blue driver scan tool and it said the same thing yours did module needing calibration the only problem is blue driver does not have the calibration feature yours does
I read in a forum your not supposed to put any electrical wires to that harness because it interferes with the electrical signal triggering the warning to check BSD system
Love you
My car is doing this right now. Only 20k miles. I can restart car and it works again for short while. Sensor mounts getting slightly loose?
Possibly loose. Was it involved in an accident? If not it should be under warranty from the dealer
How to calibrate drive motor position sensor
Hello is this the ms908s or ms908s pro? Do I need the j2534 for this?
Serge Ma hi this is not the pro. You do not need the j2534 for this
thanck you
My 2018 toyota corolla blind spot flashing on the dashboard how should I do with that please ?
Most likely the sensor is misaligned. You need to have it checked out by a bodyshop or dealer. Or a shop that has a scan tool with ADAS capabilities
Hi dear eng can i install orignal bsd system on kia sorento 2016 with out traction control i install it but error time can out signal abs esp esc can skip this error the system work in display screen note check bsd system i made calbration but error need the esc sysem pls help me
C162587 can time out abs esc esp
2020 tells me to drive above 45 kmph for 1 hour. After doing the coding. Nobody got time for that. But driving anyway and usually these take 15 mins, but nothing yet 😢
Can you do this with the im608
I’ve never used an im608 but the description says “all systems diagnostics” so I would assume that yes, you can do it with the im608 but again I’ve never used one so can’t tell you I’m 100% sure. You can contact autel and they’ll be able to tell you for sure.
How disable BSD? My kia sedona 2016 have not bsd but I bought speedometer for sxl(my kia is ex) without bsd. Every day I must cancel information "check bsd system"
Is possible reprograming? speedometer via obd?
You might be able to access the variant code on the speedometer through a scanner and disable the BSD.
@@themodernmechanic428 thanks for advice. Which of the scanners can disable bsd? Only orginal from kia service?
I have a 2018 Elantra GT. The BSD error message has popped up twice in the last month. Got it fixed once and it's back. Back to the dealer I go I guess
Has the car been in an accident? Do you know what they fixed the first time?
@@themodernmechanic428 yes, but it was only a light tap in the front, just enough to crack the grill. Nowhere near the sensors in the back. The dealer recalibrated the BSD, presumably what you did here. What causes them to get out of calibration besides an accident?
Front end shouldn’t affect it and they don’t misalign on their own. Most likely it’s a defective sensor.
@@themodernmechanic428 cool. I'll be short with them when I take it in. I'll ask for a replacement. Thanks.
i have same problem on mine.i have 2018 Elantra.if i calibrate it.its good for 8 to 10 days.but bds light come back again.help would be appreciate it.
Was the car involved in an accident? The sensor could be misaligned very slightly and eventually throws a code.
The Modern Mechanic if thats the case, will calibration fix the problem or need to replace the sensor. Because my dad bump my car in to the wall and after that the sensor activates when I’m driving even though there is no car coming, only parked cars on the side. So annoying. The bumper is fixed btw. Just need to push it back to place. No scratch.
@@themodernmechanic428 would it possibly throw other codes? Or cause other electrical components to not work?
I bought a used blind spot module for my Telluride so I need to get it calibrated
Before you try replacing the sensor, try just pressing on the sensor to sit it better in its bracket czcams.com/video/lgixiTwyFCA/video.html I think these sensors just move slightly on the bracket when the car goes on poor road or pothole (or get bumped in car parking), and the sensor moves very slightly which causes the computer to see it misaligned and the system shuts off
Do you have any idea about frequency band for front radar Hyundai Sonata limited 2016??
What if it’s smashed in 😂
@@ferds814 $$$
Can you please share the name or link to buy the software you are using?
You'll need access to an Altel MS606 or MS608 that has this capability.
Hello. Badly need your help. I would appreciate it.
Hey!
I recently got my mirror fixed by a local mechanic and now it says “CHECK BSD SYSTEM” (after paying $100 for the mirror and then $63 for the mechanic to put it in). I called the dealership and they said it would take $175 to fix whatever the problem is ... please help 😩
Hello, your problem could be 1 of 2 things. Either you got the wrong mirror (meaning you got the one without blind spot) or your mechanic didn’t connect one of the plugs on the mirror. I would take it to your mechanic and ask him to verify he connected the mirror correctly. Also verify that the mirror you installed is in fact the one with BSD. Blind spot
The Modern Mechanic thank you for your reply! so apparently, the mirror I have doesn’t have the sensor (according to 1AUTO, the place where I bought it). However, I still have my old mirror (that’s broken) but the sensor still works, can the mechanic remove the sensor from the one one and put it in the new one and will that somehow clear the warning?
Hi, the sensor is not on the actual mirror, the sensor goes behind your rear bumper. The mirror only has the indicator light which lights up when there’s a car in your blind spot. you will need to get the correct mirror. That’s the only way to fix it
I have the same problem now
I have the same issue and nobody helped me solve it. 2017 sonata shows the same error “missing calibration “ but when I calibrate it, it comes back in a very short time. What should I do?
The car damage is in the left back, Does it effect if the radar isn’t in the right place, like 1 cm or 2 away??? And how can I adjust it ?? Is there any way I can do that???
If there is damage to where the radar is mounted to it will not work. The sensor has to be at the correct angle. You can try using an angle finder or measuring tape to compare the angles from the other radar and try to somehow adjust the damaged part. Sometimes I also use my iPhone level feature to measure the angles and adjust accordingly.
The Modern Mechanic can you please make a video of how to do that?
@@themodernmechanic428 what is the correct angle? From what i saw on youtube it must be 25 degrees? There's this special drawing with 25 degrees lines that they put on the floor behind the car and align sensors with it. Am i correct?
Hey. I took my car into the service department where I bought it because I am getting that same BSD ck signal. They said that it looked like someone backed into my back bumper and it damaged the control to the BSD. They told me Hyundai wouldn't warranty it because it had been damaged. They quoted me almost $800 to replace and calibrate it. They told me the calibration would take 6 hours and they would charge me $110 per hour labor for that. In this video it looks liked you calibrated it within minutes. I think they are trying to cheat me. What do you think?
I think they meant it would take 6 hours to replace and calibrate the sensor which would require to remove the bumper. That makes more sense but 6 hours just to calibrate, definitely not because it only takes about 5 minutes. You should consider going to a body shop and get an estimate. Most body shops only charge about $60 an hour.
1000.00 for me in Florida. I"m not fixing it.
@@zatosan729 be careful not fixing it. I let one go for about 6 months or so and now the dealer is claiming it caused all the electronics in my car to short out. I think there’s some other problem but they’re claiming it’s a broken sensor from probably somebody backing into my car.
@@thomasdempsey678 did other electronics in your car truly start going out after leaving it? I got bumped into and got the dent fixed w/o insurance and a friend noticed the sensor unplugged so he just screwed it back in. I've gotten the Check BSD and RTC sensor triangle but was just going to leave it, as I didn't really anticipate it causing any other huge issues (aside from no blind spot/backup collision warnings)
@@zatosan729 in the same boat, in Florida. How did yours hold up since 10 months ago? It doesn't really make a different in terms of my driving, as my old car didn't have it, so I was just going to leave it, too; interested to hear how yours turned out and if it was fine
Barangnya dmna,si ahbee tanya
Variant coding should be done first before calibration.
That’s a good point you bring up, you will actually get a Diagnostic Trouble Code when Variant Coding is required. On this specific one I did in this video it did not ask for Variant Coding.
@@themodernmechanic428 With any new bsd sensor variant coding is used to write vehicle equipment information into the module. So even if it's not asking for variant coding it should actually still be done.
Thank you for this info, I will definitely look more into it. From what I’ve learned, Variant Coding is used when 1 module is used for several different vehicle models therefore you need to specify what model and what options the vehicle you are installing the module in has, which is done by writing the variant code. However some modules are vehicle specific and already come preloaded with the variant code as was this module however it is good practice to verify that the variant code is correct which can be done by going Into the module’s info. Thanks again for bringing this up as it is very good information.
@@themodernmechanic428 and what is variant coding? And is it hard to do?
@@sirgergorymmmc2231 variant coding is where you input a code into the module to let it know what model car it’s being installed in. It is not hard to do and can be done with this same scanner.