Sir I love your videos on electricity. Please can you make video wiring an ATS using magnetic contactors with a relay and red light ti I dicate grid ON and blue light to indicate Gen ON. If possible,do it on the single phase and three phase.Thanks
The breaker only sees the short circuit current for which it is designed through its output, in this diagram the lower terminals. Everything is OK until that part of the scheme
My question is where does the generator get the signal to start automatically, and how is it started? Is the generator started manually? I'm puzzled by the two questions!
Major error. The breakers are wired wrong. With the lettering right side up, the power comes in from the top and out the bottom. The line is always on the switch side of the breaker while the thermal trip is to be on the Load side. Many of the breakers will even be marked as to Line on top and Load on the bottom.
@@xsureface You do need to follow this even with AC. The breakers are designed to kill power in the breaker with the breaker open. Not with power still being on on the switch part of the breaker or the thermal trip. You can have a short in the breaker and you would still have power supplied to the other parts of it unless the contact side is where the line comes in. It also has to due with the arc path when the breaker opens under load. The blink breakers are clearly marked as to line in is at the top as that is where the contact is.
its good explanation but there is no way a generator will work automatic hence you add controo cable to triger the generator switch. meaning ignation for the generator must have to be controller through timer method
Look like a portable generator in the drawing. I know a standby generator will power up and automatically switch once the voltage and frequency is stable. how does the portable accomplish that please?
Australian electricians beware. You do NOT switch the neutral, as they have on this animation, on an Australian installation. Refer to AS/NZS 3000 for guidance.
In some cases, you do have to switch a Neutral. There are some inverters that the Neutral is not really a Neutral and if you wire them in without killing the house Neutral, you will blow up the inverter.
@@gravelydon7072 if you have a solar inverter, you need to separate that from the load on the ats for this reason. I am a licenced electrician, and did this one own installation. If you read the relevant section of AS/ NZS 3000, the opening statements, in bold, state you will not switch the neutral. Period.
@@ralphblundell9479 As I can't access those standards on the web, I will have to take your word for it. Under the NEC in the US, we are allowed to stitch Neutrals as long as the Breaker or Switch opens all of the connections at the same time on a breaker or opens all of the connections for the Lines and Neutrals on each side of an ATS for the incoming powers to a load. Example is 430.105: “One pole of the disconnecting means shall be permitted to disconnect a permanently grounded conductor, provided the disconnecting means is designed so that the pole in the grounded conductor cannot be opened without simultaneously disconnecting all conductors of the circuit.” As some models of inverters have problems with grounded systems on 120Volt systems, I built my ATS as a unit with switched Lines, Neutrals and Grounds. My current inverter does not have that problem but one of the backup ones does.
@@gravelydon7072 OK, I thought we might be working from different sets of standards-- it is quite specific in our case. I'm assuming it is due to our MEN earthing system which is almost universally used in Australia apart from specialist applications such as underground mining. So, we are both correct, within our own applications.
@@ralphblundell9479 No MENS type system here as our transformer feeds us alone and the Neutral comes from the center tap on the transformer. Same applies to the inverter and the generator. The generator shares the Neutral to ground bond of the house and the ground rod. The inverter can share the same but also has its own ground and ground rod as the two can operate independently. Takes a 4 wire cable from the shed to either of the three transfer switches.The whole house transfer switch ( 200 Amp fused but able to be used with up to 600 Amp ( and 3 phase if the extra contacts were installed ) ) also serves as a main disconnect. There is another transfer switch inside the house that allows use of the emergency circuits. That can be fed by a generator/inverter even while the whole house one is turned off. the third is the ATS one which only operates on 120V for a refrigerator and/or a one tube A/C. The ATS will soon be removed as the newest inverter can act as an UPS and/or an ATS on its own.
Does the ATS turns on the generator to make it automatic? When you look at the the single pole breaker and the generator there is a need to be turned on when grid power is off
Thats what i asked my self ...because even without a breaker or isolator on generator manually you have to get up turn it to start ...i think he should have used inveter instant ... Inveter with solar array and battries this automatically they on 24/7
My question is, the N side of my switch the UN light is on but the NON light is not and when i turn on my generator the R side both lights are on but on the N side only one and it hum like hell, what is the cause of this please.
It works like an RCD and I balance trips it over automatically when the mains drop off and back when it returns simple really and very fast without the danger of back-feeding the circuits.
mình rất cần mạch đảo chiều luân phiên 2 công tơ điện khác nhau dùng 2 contator và timer hẹn giờ tháng thêm 3-position switch lock để có thể dùng 2 chế độ băng man và automatic bạn ơi!
Is it not possible to provide a modified sine wave inverter for source B? When the inverter is turned on, there is a loud noise. (when source A is not set to Auto) Is that because of modified sine wave? Normal ceb power is given to Source A. When both Source A and B are given, when A is missing, Auto will come to B. But when source B is turned off and ceb power is lost, when source B is turned on, source B does not fall in auto, there is a loud noise. Why is this happening? Pure sine wave will be fine?
I cannot find an automatic switch that handles DC to DC 48 v array 100 amps I am not using an inverter, I have two 48v solar battery array, I want to use one as a back up, the only item I have hooked to it is connected directly to the MPPT charger. I would like to switch automatically one battery power bank to another when the voltage drop, the switch’s I found don’t handle 100amp input. Any suggestions how to find? I don’t want inverters at all, it would not be necessary for my application, it would only add problems. Thank you
Perdona que te diga pero creo que el video de explicación esta mal, la corriente de motor y red no entra x abajo de los diferenciales sino x arriba. Excuse me for telling you but I think the explanation video is wrong, the motor and mains current does not enter x below the differentials but x above.
Quisiera saber si puedo usar ATS de 3p para 220v de dos fases de 110v mas un neutro , y en la reserva solo 110 Volt , una fase de 110 Volt más el.neutro
Buenas tarde quisiera aver por que pone la alimentacion principal agua bajo de breykel tricfasico y buel y hace la misma operacion todo lo de mas quiero saber si el pais de donde eres es un nuevo codigo de trabaja alla soy re publica dominicana ariel martinez tecnico de electrico industrial y refigeracion Dios te vendiga es pero tu repuesta
Thats why ATS its there to trigger Generator when thes no voltage on grid side ....ATS will select the side with voltage and gen will start if grid power comes back ATS will select grid then gen will stop just like that
Its no ATS. ( Automatic ) Is Manual . ATS need outs for starth Power generator. Eso no es tansferencia automatica ... es manual . se nesecita la salida para arrancar al generador .
@@JrElectricSchool Its the power generator original part ? need open fuel line .turn on ignicion. activ chocke . start motor for run and fee chocke when run. (No represented diagram)
Ma che cosa è.......... Anche il mio gatto 🐱🐈 e capace a fare un video così Inoltre da noi normalmente l entrata magnetotermico e sopra e uscita sotto Forse da voi in stupilandia è al contrario 😱😱😱
People everywhere may well be needing more of this kind of tech info.
Las normas indican que la tensión debe ingresar por arriba por lo cual las llaves están conectadas mal
Very commendable diagram. Clear and easy to follow. MCB electrical code is still important.
Very very beautiful, thanks for sharing my friend 👍🤩
fully watched 👌♥️♥️
Thank you so much 🙂
In spite of possible errors depending on country, this is a well-drawn schematic which many will find useful. Keep up the good work.
Occurs
Teşekkürler dostum.Türkiyeden selamlar... Bu projeye ihtiyacım vardı..!!
Sir I love your videos on electricity.
Please can you make video wiring an ATS using magnetic contactors with a relay and red light ti I dicate grid ON and blue light to indicate Gen ON. If possible,do it on the single phase and three phase.Thanks
Very good information
Thank you so much 🙂
Great work, keep it up.
Thanks
Love the song.
All the best
Thanks for watching
Keep blowing the horn. For it's great the work indeed.
Thanks
You are welcome.
The breaker only sees the short circuit current for which it is designed through its output, in this diagram the lower terminals. Everything is OK until that part of the scheme
Já instalei esse modelo em área rural aqui no Brasil
This song hits 💯
Thank you for sharing..
Welcome
My question is where does the generator get the signal to start automatically, and how is it started? Is the generator started manually? I'm puzzled by the two questions!
Major error. The breakers are wired wrong. With the lettering right side up, the power comes in from the top and out the bottom. The line is always on the switch side of the breaker while the thermal trip is to be on the Load side. Many of the breakers will even be marked as to Line on top and Load on the bottom.
you don't need to follow this, unless you are using dc. Normal way ist AC, so they don't care.
@@xsureface You do need to follow this even with AC. The breakers are designed to kill power in the breaker with the breaker open. Not with power still being on on the switch part of the breaker or the thermal trip. You can have a short in the breaker and you would still have power supplied to the other parts of it unless the contact side is where the line comes in. It also has to due with the arc path when the breaker opens under load. The blink breakers are clearly marked as to line in is at the top as that is where the contact is.
@@gravelydon7072 you have absolutely no idea what you're on about.
Good work
Nice video, thanks :)
Thank you too!
@@JrElectricSchool hm ko chaiy kis mag ba sakte h is ko
Thank brother ❤️🥀
Welcome
What is the name of this software?
Novo no canal, Gustavo - Maceió - Brasil👍
A wiring commentary would be helpful
Nice video
its good explanation but there is no way a generator will work automatic hence you add controo cable to triger the generator switch. meaning ignation for the generator must have to be controller through timer method
where does the black and green arrow pointing up go? great video by the way
Black is return, and green I assume is ground since it is the third wire and color coded green.
Very nice video, but where the black line from the top of breaker go with pill up beside earth line green?
Great video!!! Do you have a solar PV power and small portable generator manual switch video? TIA...
Très cool
Más fácil que el agua no pudo ser
You should complete the drawing,what about the automation.
👍
Thanks for watching👍
Según la norma debería ingresar lo por arriba⬇️ 🤷
Thanks for watching
Nice
Thank you so much 🙂
Look like a portable generator in the drawing. I know a standby generator will power up and automatically switch once the voltage and frequency is stable. how does the portable accomplish that please?
Admittedly I am an electrical novice however where does the ground wire go?
thx
Thanks for watching
What is E? The green line, is this earth ground I assume?
E is earth
Sir kon sa software use krty ho plz
How is this not backfeeding the grid through the nuetral wire?
how to add the Pilot lamp buzzer that alerts when grid power is back
Australian electricians beware. You do NOT switch the neutral, as they have on this animation, on an Australian installation. Refer to AS/NZS 3000 for guidance.
In some cases, you do have to switch a Neutral. There are some inverters that the Neutral is not really a Neutral and if you wire them in without killing the house Neutral, you will blow up the inverter.
@@gravelydon7072 if you have a solar inverter, you need to separate that from the load on the ats for this reason. I am a licenced electrician, and did this one own installation. If you read the relevant section of AS/ NZS 3000, the opening statements, in bold, state you will not switch the neutral. Period.
@@ralphblundell9479 As I can't access those standards on the web, I will have to take your word for it. Under the NEC in the US, we are allowed to stitch Neutrals as long as the Breaker or Switch opens all of the connections at the same time on a breaker or opens all of the connections for the Lines and Neutrals on each side of an ATS for the incoming powers to a load. Example is 430.105: “One pole of the disconnecting means shall be permitted to disconnect a permanently grounded conductor, provided the disconnecting means is designed so that the pole in the grounded conductor cannot be opened without simultaneously disconnecting all conductors of the circuit.” As some models of inverters have problems with grounded systems on 120Volt systems, I built my ATS as a unit with switched Lines, Neutrals and Grounds. My current inverter does not have that problem but one of the backup ones does.
@@gravelydon7072 OK, I thought we might be working from different sets of standards-- it is quite specific in our case. I'm assuming it is due to our MEN earthing system which is almost universally used in Australia apart from specialist applications such as underground mining. So, we are both correct, within our own applications.
@@ralphblundell9479 No MENS type system here as our transformer feeds us alone and the Neutral comes from the center tap on the transformer. Same applies to the inverter and the generator. The generator shares the Neutral to ground bond of the house and the ground rod. The inverter can share the same but also has its own ground and ground rod as the two can operate independently. Takes a 4 wire cable from the shed to either of the three transfer switches.The whole house transfer switch ( 200 Amp fused but able to be used with up to 600 Amp ( and 3 phase if the extra contacts were installed ) ) also serves as a main disconnect. There is another transfer switch inside the house that allows use of the emergency circuits. That can be fed by a generator/inverter even while the whole house one is turned off. the third is the ATS one which only operates on 120V for a refrigerator and/or a one tube A/C. The ATS will soon be removed as the newest inverter can act as an UPS and/or an ATS on its own.
It can bi able to put a not the same voltage, example in the normal power I put a 220v, and in the reserve power is 12v?
Merci j'en ai un mais n'avait pas compris comment le brancher.
the only question i have is, is the transfer uninterrupted?
Great where do i get this as switch on the video?
Does the ATS turns on the generator to make it automatic? When you look at the the single pole breaker and the generator there is a need to be turned on when grid power is off
Thats what i asked my self ...because even without a breaker or isolator on generator manually you have to get up turn it to start ...i think he should have used inveter instant ... Inveter with solar array and battries this automatically they on 24/7
Ta doido, entrar com alta tensâo direta da torre, aqui passa por um trafo de baixa tensão em 220 Vca.
My question is, the N side of my switch the UN light is on but the NON light is not and when i turn on my generator the R side both lights are on but on the N side only one and it hum like hell, what is the cause of this please.
We need that but with 2 contactor
Thanks for share your opinion i will try to make video on your topic.
I don't see it being automatic. An ATS. Turns the generator on and switches the load, as soon as it loses power.
It works like an RCD and I balance trips it over automatically when the mains drop off and back when it returns simple really and very fast without the danger of back-feeding the circuits.
Can this ATS send a start signal to the generator?
mình rất cần mạch đảo chiều luân phiên 2 công tơ điện khác nhau dùng 2 contator và timer hẹn giờ tháng thêm 3-position switch lock để có thể dùng 2 chế độ băng man và automatic bạn ơi!
sorry i am not understand your language please tell me Bangla,Hindi,English. Thank you
It will automatically switch on the generator with this system.
Same also available amf panel also
Looks like Eruro set up, not USA.
E for Ground
Is it not possible to provide a modified sine wave inverter for source B? When the inverter is turned on, there is a loud noise. (when source A is not set to Auto)
Is that because of modified sine wave? Normal ceb power is given to Source A. When both Source A and B are given, when A is missing, Auto will come to B. But when source B is turned off and ceb power is lost, when source B is turned on, source B does not fall in auto, there is a loud noise.
Why is this happening?
Pure sine wave will be fine?
In our home we have six change over
I want to remove it
How can I make it automatically change over
Battery connection 12v or 24 vdc
I cannot find an automatic switch that handles DC to DC 48 v array 100 amps
I am not using an inverter,
I have two 48v solar battery array, I want to use one as a back up, the only item I have hooked to it is connected directly to the MPPT charger.
I would like to switch automatically one battery power bank to another when the voltage drop, the switch’s I found don’t handle 100amp input.
Any suggestions how to find?
I don’t want inverters at all, it would not be necessary for my application, it would only add problems.
Thank you
The 2:26 minutes can be shorten to a picture… and besides, even then it provides absolutely no information.
Hi is a single phase Chengeover rotory db
Perdona que te diga pero creo que el video de explicación esta mal, la corriente de motor y red no entra x abajo de los diferenciales sino x arriba.
Excuse me for telling you but I think the explanation video is wrong, the motor and mains current does not enter x below the differentials but x above.
А почему питание подаёшь на нижние клеммы вводных автоматов. Нехорошо.
pudi pa boss battery imbes na generator?
el selector es sin paso por cero (0)? no quero que se reinicie mis equipos
Quisiera saber si puedo usar ATS de 3p para 220v de dos fases de 110v mas un neutro , y en la reserva solo 110 Volt , una fase de 110 Volt más el.neutro
Errado , faltou o inversor de potência,pra mandar pra chave ou disjuntor
nguồn công tơ 1 sử dụng 15 ngày nguồn công tơ 2 sử dụng 15 ngày trong tháng mong được bạn chia sẻ!
sorry i am not understand your language please tell me Bangla,Hindi,English. Thank you
bạn chỉ cần một bộ hẹn giờ 15 ngày ở một trong những phía cung cấp điện trước ATS.
@@michaelseah9617 thanks you bạn!
What is it equipement sir?
Error al alimentar por debajo el braker principal
M b vido banata hun es software ka name bata dy plz
Brother one dout breaker side small four Tarminals hear what is that four Tarminals
What is the name of a software? Please 🙏
Bro What is the name of this software?🙏🙏
Buenas tarde quisiera aver por que pone la alimentacion principal agua bajo de breykel tricfasico y buel y hace la misma operacion todo lo de mas quiero saber si el pais de donde eres es un nuevo codigo de trabaja alla soy re publica dominicana ariel martinez tecnico de electrico industrial y refigeracion Dios te vendiga es pero tu repuesta
wrong connection from ats to main circuit breaker it should be on line side instead of load side
Gb
Thank you very much!
Esté circuito NO es permitirle en EUROPA. Cuando cuándo pongáis semejante circuito pronunciar para que PAÍSES SON..
How to start generator automatically when grid power outage?
Thats why ATS its there to trigger Generator when thes no voltage on grid side ....ATS will select the side with voltage and gen will start if grid power comes back ATS will select grid then gen will stop just like that
Its no ATS. ( Automatic ) Is Manual . ATS need outs for starth Power generator. Eso no es tansferencia automatica ... es manual . se nesecita la salida para arrancar al generador .
no sir its automatic
@@JrElectricSchool Its the power generator original part ? need open fuel line .turn on ignicion. activ chocke . start motor for run and fee chocke when run. (No represented diagram)
Free diagram of bc booster
sir kaya kaya nyan 500watts na aircon? o.5
Mts
Thanks for watching
Ilang amper ung ats na yan?
అన్నా ఏ సిటీ డిసిపి కంట్రోల్ చేసేది నేమ్ ఏంటి
😊👍👍👍👍👍☆☆☆☆☆.
Dont use music
Thank you so much for share your opinion
Sir Price
In your diagram why supply side of the breaker you put the load..
this is pfusch no selektivity
Ввод питания автоматов всегда сверху! Дурни!
This is not automated scheme.
yes its automatic
May I know switching time
Nothing "Automatic" about this arrangement. It is totally manual control!
Even says on switch at top automatic one side manual other
really stupid music and unnecessary animations !!! not cool!!! 100% not cool!
we are so sorry for you music problem we will try to solve music.
Thank you so much!
Ma che cosa è.......... Anche il mio gatto 🐱🐈 e capace a fare un video così
Inoltre da noi normalmente l entrata magnetotermico e sopra e uscita sotto
Forse da voi in stupilandia è al contrario 😱😱😱
🤮
Thanks for watching
Admittedly I am an electrical novice however where does the ground wire go?
It goes to the ground bus bar in the electrical panel. The black goes to the return bus bar Ina 120 volts circuit.