Installing Security Window Film on a Sliding Glass Door: A Step-by-Step Guide Film Install (Part 1)
Vložit
- čas přidán 15. 07. 2023
- This comprehensive guide presents a step-by-step installation process of security window film on a sliding glass door by RC Window Films. This guide caters to professionals and DIY enthusiasts looking to bolster their home security.
Part 1: Preparing the Window
Before installing, ensure the glass door is thoroughly cleaned to remove dust, dirt, or grime. The cleaner the glass, the better the window film will adhere.
Begin by cleaning the glass with a high-quality glass cleaner and a lint-free cloth.
Scrape off any residual adhesive or paint using a razor blade.
Finish off by wiping the glass with a microfiber cloth for a spotless finish.
Part 2: Measuring and Cutting the Film
This step involves carefully measuring and cutting the window film to precisely fit your sliding glass door.
Here's what you'll need:
Cleaning squeegee--------- amzn.to/42TS7Bo
-Scotch Brite Blue pad (non-marring)-------amzn.to/3P0SEeS
-Olfa blade ---------amzn.to/4bWq9Js
Squeegee for installation --------- amzn.to/3TdslVn
-Tape measure ------amzn.to/3uZx8jQ
-Hard card-------------amzn.to/3SWMRIp
-Spray bottle with a mixture of water and Dawn dish soap -----------amzn.to/3uWhcPl
-Paper towels (Bounty recommended for its durability) -------------amzn.to/3uZxC9E
Tools:
amzn.to/3uSHOkn Pouch
amzn.to/4bPCC1f Toolbelt
amzn.to/3IcbUT4 Tool-bag
amzn.to/3SVd2zh Caulking Tips
Measure the dimensions of the glass on your sliding door using a measuring tape.
Roll out the window film onto a clean, flat surface and mark the required dimensions.
Use a straight edge and a sharp utility knife to cut the film, leaving an extra inch on each side for adjustments.
Part 3: Applying the Film
We'll apply the window film onto the glass door in this part.
Spray the glass with a solution of soap and water.
Peel away the backing from the window film.
Apply the adhesive side of the film onto the wet glass.
Use a squeegee to smooth out the film, working from the center outwards to push out any air bubbles.
Trim the excess film from the edges using a utility knife.
Coming Up: Strengthening the Film with Dow Corning 995
Dow Corning 995
Stay tuned for our next video, where we will demonstrate the application of Dow Corning 995 - a structural silicone attachment system designed to fortify the connection between the window film and the frame. This step is crucial for maximizing the strength and durability of the security window film installation. It ensures the film stays intact even under severe impact, offering the ideal scenario for maximum protection when the existing frame is present.
Make sure to watch this follow-up video for a deeper understanding of how to elevate the security measures of your sliding glass door.
Remember, safety should be your utmost priority while performing these steps. Always use appropriate personal protective equipment and seek professional assistance if needed.
Part 4: Tools and Materials
Before proceeding, ensure you have all the necessary tools and materials. This includes:
High-quality security window film
Glass cleaner
Lint-free and microfiber cloths
Razor blade
Measuring tape
Straight edge
Sharp utility knife
Soap and water solution
Spray bottle
Squeegee
Dow Corning 995 structural silicone attachment system
Part 5: Safety Considerations
Remember to use safety glasses to protect your eyes from debris when handling the security film and installing it onto your sliding glass door. It's also essential to handle the utility knife cautiously to prevent accidents.
Part 6: Tips for a Successful Installation
Be patient: Applying the security film is a delicate process that can't be rushed. Take your time to avoid mistakes and ensure a smooth installation.
Ensure a clean workspace: Keep your workspace clean and free of dust or debris that could stick to the film.
Use plenty of soap solution: It helps the film slide quickly on the glass and makes it easier to position correctly.
Eliminate all bubbles: Use the squeegee to press out any bubbles under the film. This ensures a smooth finish and helps the film adhere appropriately to the glass.
Our following tutorial will investigate installing the Dow Corning 995 structural silicone attachment system.
Adding this product will drastically enhance the strength and durability of your window film, so be sure not to miss it. This crucial step is your pathway to unparalleled window security.
Stay tuned for our upcoming video guide for the ultimate protection with the existing frame present.
That's it for our guide on installing security window film on a sliding glass door.
Remember, while it's a straightforward process that DIYers can tackle, professional help is recommended to guarantee perfect fit and maximum security benefits. Happy installing!
Learn more at: www.rcwindowfilms.com/
Get a quote: www.rcwindowfilms.com/get-a-q...
You’re a pro…made it look easy!
Thank you!
thankyou for the new learning , i just start my own business for window tinting in bali and i learn verry much from you!!
heck, yeah! Congrats, let me know if you need anything. Like a video request.
@@rcwindowfilms Do you know the reason why sometimes when I install window film there are lots of white spots? i think I'm clean enough to clean the glass
@@arullsticker it may be that you to clean out your filter if your not using one or maybe try using one. Clean filtered water is best. Us an rv filter that will help.
Great details
Thanks, hey if you have any questions or have anything to add, please let me know. I'm always happy to hear other perspectives
It is briliant bottle, where did you get this my friend? Also that tissue holder is so hard to get here
Can this be installed to the inside and outdoor of the door ?
Great video; you make this look easy and appreciate you demystifying the process. One question the Dow 995 is easy enough to find on the web- where can anyone buy directly the 3M protective film; they seem to only make it available via installers? Do you sell direct and if so how do I order through you?
Yes, you most definitely can order through us. Most manufacturers offer the film to dealers only.
Thank You for sharing your "Brilliant" method of controlling the roll of sticky "Cling Wrap" by routing the backing out of the way as you unroll. Last time I did this same job I pulled the backing off and that was the beginning of the end for that attempt at doing a clean job... That was the worst experience I had in over a year of remodeling this house... I am going to redo it with the 8 mil 05 tinted security film, I had been dreading it until now... Again Thank You..!
ONE (poss. dumb) question... I assume this film needs to go on bare, clean glass, and NOT over any film that is currently on the glass from two years ago..?
In other words, do I need to remove the film that I installed a couple years back.. Or can this actually be applied over the film that is on the glass now?
Great video what wimdow film are you using?
Thanks bud we use a wide variety of films. For this installation we did a eight mil Solar Gard 20 silver
@@rcwindowfilms Thank ypu!
Would you recommend a 5" or 8" fusion stretch handle for installing 8 mil security film? I can see youre using a 5 with a red refil, however an 8 would mean youre able to get more done. However i reckon with the 5 youre able to be sure to get more water out with each stroke as less surface area? Any advice would help! Thanks!
5 inch all the way, sorry for the late reply. For us we use the 5 inch all the time.
@@rcwindowfilms Thank you man, much aopreciated!
@rcwindowfilms I also have another question, what refil would you recommend for security film (8 mil) I see you're using a red refil but I am more familiar with the bluemax.
@@TheArcesz the red for eight mil and up. The more water you’re able to get out on one pass the faster you’re film will cure , and the less spots of water will remain. Single pass squeegeeing with a red squeegee preferably square face will give you the most consistent results.
@rcwindowfilms Hey man I'd also like to ask what you're opinion is on the "big mouth" squeegees for security film. It looks like you're using 1/4" blades (based off the squeegee you have) I work with people that swear by them however I think they're a bit overkill for 8 mil film, seeing as I'm a young guy and can get all the water out with just a regular 1/4 bluemax in my fusion in one pass.
Is it something you use in any other application in your business?
Nice install! What’s your go-to reliable glass cleaning method when prepping for film installation? Got any tips for hard water stains and buffing out older windows?
That’s a pretty tricky question. It really depends on the situation. Most times you’re not gonna need an acid to remove hard water stains however, depending on the type of glass, it may differ is there a particular situation that you want me to guide you on?
@@rcwindowfilms I was thinking of standard dual pane patio windows, that may have some stains and micro scratches from years of environmental exposure. Would you recommend putting the film on both outer and inner pane?
@@RafaelSwit When considering the application of a film to your glass, I recommend opting for an interior film installation. Given the level of scratches and damage already present on the exterior glass, an interior film is likely to be more durable and longer lasting. This choice takes into account both the environmental impact and the current condition of the existing glass. Choosing an interior film is a strategic decision for enhancing the glass's longevity and maintaining its quality, as the exterior glass unit that exists currently will require more deep cleaning because of the surface scratches and damage present.
Thank you. I appreciate it. I have a great electric pump set up. With a water pump if you interested. No need for a compressor anymore. Fyi.
I’m interested email me
Do you have a link for the slip n stick
What film would u recomend for a standard window
it really depends on the use case. what are you trying to accomplish?
@@rcwindowfilms added security to my windows
You didn't do the sealing along the edges that you talked about... how do you get that done on something like a door or home window?
It’s on part 2 Dow Corning 995 Attachment for Security Film on Sliding Glass Door: A Step-by-Step Install (Part 2)
czcams.com/video/TMnmMs9oSwY/video.html
can you please send a link to this 6-inch squeegee?
Sure wish you were in the Seattle area so we could use your company for our windows.
For commercial or residential?
@@rcwindowfilms residential
You always cut the security film exactly the size you want before install?
Yes, it’s absolutely necessary that you pre-cut security film to the exact size needed. This insures better overall protection, and better overall rigidity of the film. Essentially it reduces the failure or the chance of failure due to lack of adhesion.
Where did u buy a towel handle? I’ve been in Lowe’s and Homed Depot and they don’t have it
honestly it's just a bungie cord.
How do I make a pre-cut? Can I, like the other tints, prepare a little more, and then cut the excess on the window?
A film-handler is the best way to reduce your cutting and pre-cut to close size.
Where do you get your commercial tints from? And how do you know what shades to use like one of your other videos had a broken window so you tinted one window and the others were done.
which video are you talking about?
@@rcwindowfilms step by step guide how to tint large windows. It was uploaded 5 months ago but I just watched it yesterday and I believe you used a 78 inch roll so I was curious where to buy that big of a roll and also how to check shades or know what tint to use if pre exist windows are already tinted.
@cbroner9983 We installed the tint originally, so we're aware of the film type and shade. If you're unsure, use a tint meter to determine the VLT. Matching film often needs details from the prior installation or a meter reading. Regarding roll size, it's 72 inches, which is the maximum size most manufacturers offer. For larger sizes, you might need to buy a master roll.
Can you provide a link as to where to purchase the red 6 inch application squeegee and handle ? 👍🏼
amzn.to/3uSHOkn Pouch
amzn.to/4bPCC1f Toolbelt
amzn.to/3IcbUT4 Tool-bag
amzn.to/3UVFkfy Basic Squeegee for installation
Liner I got has a heavy plastic and lighter film. Does the lighter film go in the window.
I suggest inspecting where the adhesive is and make sure to apply the film with adhesive to the glass surface.
@@rcwindowfilms thank you
what slip solution do you use?
Under soap or slip and stick
What's the belt called for all the tools? Or can you provide a link? Thanks
amzn.to/3uSHOkn Pouch
amzn.to/4bPCC1f Toolbelt
Thank you
Where can we buy the thicker type squeegee?
amzn.to/3TdslVn
Is that soapy water or regular water
Soapy water solution
Applying films both sides make the window much harder to break, compared to one side only ? Can the burglar still kick in & gain entry ?
yes, access is still possible. The whole idea is to gain time. Delay entry, doing dual film (film on both sides) is an option, but cost becomes an issue.