Solder copper pipe WITHOUT flame or blow torch
Vložit
- čas přidán 15. 10. 2021
- Today I show you how to solder copper pipe WITHOUT a naked flame or a blow torch.
BUY PIPEMASTER HERE: www.amazon.co.uk/shop/plumber...
🚀 LEARN PLUMBING ONLINE IN MY STRUCTURED COURSE (50% Before March): www.learnplumbingonline.com
🛠 AMAZON TOOL STORE: www.amazon.co.uk/shop/plumberp...
🥾 10% Off my workboots + workwear Use Plumberparts10: www.bigboots.co.uk/discount/p...
👓 10% Off Safestyle Sunglasses Use PLUMBER10: safestyle.com.au/?ref=PLUMBER10
Learn Plumbing Online is perfect for future apprentices, homeowners who want to understand and tackle more plumbing jobs in the home, handymen who keep turning down the odd plumbing job and more. With practical follow along video lessons and discussion board you can boost your knowledge in my amazing trade. Sign up now: wwwlearnplumbingonline.com
Ever wondered if you can solder copper pipe WITHOUT a blow torch or naked flame? Ever worried about buring down the house whilst fixing that copper pipe leak? Well this week I review the Pipemaster Professional Plumbing Tool. It's 'OK'....but I'll leave it up to you to decide. We solder straight couplings and elbows. We also solder capillary fittings too.
#Plumbing #Plumber #PlumbingAdvice
TWITTER🐤 www.Twitter.co.uk/plumberparts 🔥
FACEBOOK👉 www.facebook.co.uk/plumberparts 🔥
INSTAGRAM📷 / plumberparts 🔥
PLUMBERS REGISTER HERE: www.plumberparts.co.uk/tell-me... ❤️ - Jak na to + styl
*IF I HAVE TO READ ANOTHER COMMENT ABOUT THE PLIERS ACTING AS A HEAT SINK I'LL PULL MY HAIR OUT!* 😂 I did film it without the pliers and it still didn't work.
🍺 *JOIN THE Alearmy Exclusive weekly live videos on Thursday* czcams.com/users/plumberpartsjoin
🛠 *AMAZON STORE* www.amazon.co.uk/shop/plumberparts
📺 *VLOG CHANNEL:* czcams.com/users/timeswithjames
Good bit of kit for a trade who solders occasionally but doesn't want the extra cost to their insurance that comes with working with flames.
I can’t see the sense in this at all .
He talks about capiliry fillings.first why not have a clamp with a ridge which goes over the Yorkshire and not only clamps over but melts the solder
Aonde eu encontro este equipamento ?
Idk about the pliers pulling heat. But I do know from years of soldering that the solder runs to the heat source. And you have the source above the fitting. It'd be the same as having your torch in the same location. It would take eventually but the solder wouldn't run into the fitting as easily as if it was being heated on the fitting itself.
I'm an American plumber.
I got one of these years ago. I kept it on the van for a while but never used it for work. I tried it a couple times at home and admittedly I was impressed. Originally I wished it fit around the fitting, BUT that wouldn't always work because not all fittings are the same size. Once a touch of solder gets in the joint the heat transfers to the fitting much more quickly.
I still use my torch everyday, but for someone with less flame control it's certainly preferable to burning a house down.
I think the American spelling is propress🤣
@@D_pawson Have you seen the cost of Propress fittings? I have almost as many Propress fittings on the van as sweat but I still choose to sweat a lot of stuff. When it's only a couple joints the time difference is minimal and the parts cost is more important.
Sweat fittings are usually 1/2 to 1/4 the cost of Propress fittings. Also, they take up less space on the van.
@@D_pawson The Propress is also much larger than the tip of a torch so you can't Propress everything simply due to space constraints.
Yeah, maybe it would be ok for amateurs but I'll stick to my MAPP gas torch. I haven't burnt anyone's house down so far. 🤞
You shouldn’t use metal grips to grab the heating elements as it diverts the heat away from the pipe. That’s why the 22mm took longer.
I did another test that i didn't film and the grips helped loads. Just not the 'best' tool for that job. Would be miles better if they fit the outer of the fitting properly and not just the outside pipe diameter....might shave off some brass and see if that improves...
@@plumberparts I'd expect that you only need to get a couple of good points of contact onto the pipe/fitting given how good a conductor of heat that copper is. I'd agree that clamping the jaws onto the pipe is going to help, but a non-conductive clamp fitted over the plastic part of the jaws will avoid the grips sinking the heat away from the pipe/fitting.
To solve the problem. Buy that beast. Buy cheap inverter 600w. Build a small ish battery pack. Whatever your inverter work on. Buy a light dimmer. Put it all together. And you got yourself soldering station you can use on site. I wouldn't go more than 75% of a dimmer. That way it'll beat flame in every way.
I've got a set of these and they don't get a huge amount of use, but if I'm working in a confined space like a airing cupboard where it's super tight, they give me more peace of mind when I leave the job that the flame from my torch didn't do any damage or more importantly, leave anything smoldering away that I didn't or couldn't see. These days I'd probably use a push fit though.
Excellent review. Another advantage I can see is that the soldering process is less smelly than when using the open flame of a blowtorch.
Many thanks. David
Doesn't look like they "hold tight". Good review James
Yeah, sometimes needed...but not intentionally!
Very well done fella. I do believe the word is Master Plumber which comes to mind.
My first soldering iron three decades ago was an Antex. I hope it is still a British company. Good review!
Good Saturday morning to you sir and your family
I have the pipe master and it works great
Good News,and Thank you
These are real handy in confined spaces where a flame could be a problem and they do generally work well. However in some situations they can be difficult to get into position for instance with a pipe against a wall where you need to come in from the side so they don't replace a torch completely. You want to get the more powerful 220w version for 22mm pipe heats up the joint much faster.
On the big fitting where you had probs, I would advise you get the thing closer to the fitting and no clamp, don't worry about a bit of solder getting on the heater. You will only get a burn off it once, then you will become super aware of it.
Hi just to let you know I am a fan of your videos you are so good at explaning things and just love your style. I think one of the reasons the solder did not melt as good on the bigger size was beacuse you had another pliers attached to it therefore talking the heat away from thr heating element. Sorry if I am wrong, just an idea.
This would have helped me on a number of occasions where fire risk has been a real concern. On the other hand copper push fit fittings can be a life saver in such situations.
Shark bites is where it’s at
Yep the handle of the tool needs a lock clamp to hold it tight, or around the neck of the heat rods, otherwise I would be very interest as a DIY person as all my tools around the house have been turn into electric, why because I have Solar on the roof, and a battery bank in the loft, since I moved into my house 4 years ago I've been using solar power for all my jobs, the last tool I have is the blow torch!!...thanks for the review. PS I agree with 'rikmoran' placing a pair of clamps around the hot end will act as a heat sink and take longer to do the job.
Very interesting review. As someone who does more electronics soldering, this looks similar to an iron. Looks like there are a lot of improvements that could be made to the tech from soldering irons like a temperature indicator, and a proper holder. Having its own ratchetibg/ clamping handle would really help to transfer the heat too, save using grips like James did. As a DIYr these do look interesting as my torch skills are crap, but these look like they would drive me a bit mad too.
They are made by Antex after all, so the resemblance shouldn't be surprising
great videos, what's your thoughts on press fit? just seen a video, never knew it was a thing
Very good equipment!!
Great vid' as usual, can you do one on how to de-solder a joint to use again, as I was in possision where I needed to split a joint as I was not able to cut the pipe as it would have left it too short to re-joint under the floor, thanks.
Avid DIYer...
I have an Antex Pipemaster, I've twisted a hair band around the grips, this does keep the iron tight on a pipe.
I plug in iron, prep all pipes, heat 15mm pipe for 30sec, add flux, heat sleeve for 20secs, solder.
Same applies 22mm but add 10secs to heating as there is more copper to heat.
Excellent advice. Will try that.
@@happydavid13 I forgot to mention, try not to get flux on the 15-22mm heads, the internal diameter increases with corrosion and 15mm becomes 16mm.
Cracking review Jimmy - grips defo acting as a heat sink though bud! T-shirt arrived the other day - oh yeah 😎
Top man!
YEEESSSSSS YOU'RE REVIEWING THIS THING
Thats interesting… i was always under the school of thought that to get the tightest fitting you heat the fitting not the pipe, therefor the space between the fitting and pipe opens up a little more and more solder can run in, therefore when tje fitting cools there more solder material in the joint creating a tighter clamp when the joint cools to room temp… if you know what i mean.
sorry I didn't look at the other comments. It looks like you have be well informed of the problem using the grips,. Sorry to be the one to hammer that home
You can also get an attachment for the blow lamp that is a metal sheet that clips onto the lamp and hooks around the pipe your soldering... or could just use press fit if you ever with the lottery to buy the fittings
How are you bro, I have a question, can I use it for hvac tube too?
It looks like it’s a decent idea for areas when a blowtorch may be a risk but it looks like a redesign is due on it as that design is years old. A battery version would possibly be ideal or a catalytic converter type without the big flame .
You probably need to tin the Pipemaster and pipe so that there is a greater surface area that is in contact to increase the transfer of heat. This is the same principle used in soldering electronics.
For the cost of them, have you considered just getting two and having one each already set up for 15mm and 22mm?
Do you think that these would work with HVAC fittings which are an off size and 15% silver solder?
I can see uses for plumbing embedded in spray in insulation (flammable). I would still keep that fire extinguisher near at hand though.
The golden rule when soldering is don't move the pipe or fitting until the solder has cooled down or the solder might crack, I can see that there is a lot of movement of the pipe and fittings , high risk of cracked solder with this system. And I think that you mean a solder ring fitting 👍
Hi James.Does it work for refrigeration copper pipe?
Hellor sir ! Can this soldering iron solder aluminium pipe ?
Car air conditioning is using aluminium pipe only , so this tools can solder it or not ? Thanks
Hello do you know where we can buy this tolls
Not seen these before. I can see these working for me as I work in a lot of places where I can’t get hot works permit I wonder if I’d get away with using one of these ?
Amigo onde compro essa máquina?
Would the 22mm die fit better around the 15mm fittings ?
will it be clamping the tool with grips will act as heat sink sucking the heat away??
Cool stuff. When I first became an apprentice I was reading about plumbing and came across an article about a guy on his first day of plumbing who burned down some mansion. They gave him a torch and put him in the attic on his very first day. Oops! Bet he wishes he had one of these things.
Do you guys use mapp gas? Or whatever the replacement for it is? I’ve almost never used propane for soldering.
The jaws need a changing radius along the circumference so you can choose where it seats best. You'll never get 100% contact, but should always find a sweet spot for good contact surface area over half the pipe.
Unless the pipe or fitting is perfectly matched, these seem to rely on a few points of contact which is horribly inefficient.
If the clamp bits were bored out to fit the outside of the female fitting, I think that would solve most of the problems. I think they should fit the fitting quite will to work as intended. Thanks for the vid!
I bought one because I liked the idea for soldering in a very tight spot but as you show I thought exactly the same the clamp system doesn’t seem to hold the pipe properly which then takes longer to solder than it should
Definitely a diyers tool with Yorkshire fittings would be really good for every now and again use.
Hey I used heavy rubber strapping to pull tight the handles, no issue with the heatsink issue. Too bad we can't use an induction heater to heat up copper but I see a problem at slipping the coil round pipe that it would become entrapped into the mess. Now if someone could come up with a split coil induction heater for copper it would be nice.
I like it mr smiler
And what is that tool he used to apply the flux? So cool
Could it be that on the 22mm pipe when you held the clamp on with the grips a bit of the heat dissipation went fractionally into the grips.?
It makes complete sense to me, that the heat will disperse to the clamp
So is it conduction, or induction? Ive seen it advertised both ways...
As an electronics technician, we always tin the wire with a bit of solder to aid conduction, I'm certain this same method would work with the pipemaster, I came on here to say about the conduction of the molegrip but notice 175 comments already mention it, by the way if you was using the torch would you be heating the pipe or the t?
Hello sir , is it podsible to solder CAR AIR CONDITIONER ALUMINIUM PIPE ? thanks ,
Putting a pair of grips on the heat source takes the heat out of the elements, your're heating the grips.
glad someone mentioned it.
Pinned comment.
Pinned comment.
Think this would be useful doing pipes in a cabinet for example. You could get a bag that people use for hair straightness to keep them in
speaking as a world champion in making leaky joints, a couple of ideas.
how about putting a spring between the handles to hold the grips tighter, also, a tube lined with heat resistant stuff as a holder so the hot bits are in a safe place when not in use ?
Don't forget that if you use a metal tool to grip the soldering heads the iron has to heat the tool up as well as the joint. That can be a lot of metal (try using your blowtorch under water 😄).
Hi guys this machine can use with copper wilding rods? using with high pressure.
Try the Rotherm 2000 from rothenberger. Looks a little more robust.
Hi James, the rothenberger or REMs units are much better. Maybe see if they will loan one for you to demonstrate. They heat the pipe in seconds.
I'll just buy one. Don't have anything to do with tool manufacturers apart from the bosch massive.
@@plumberparts Looking forward to it's review! It means no more gas!
@@plumberparts , get the rothenberger rotherm 2000, it's impressive.
Yea I was actually looking into buying the rems version, would be nice to see it in action
Is that the induction heating one?
Rather than metal clamp at the hot end, maybe a different bodge might work?
cable tie loosely around both handles. Move cable tie as far as possible from pivot. Tighten cable tie when tool clamped on work . Place Dab of superglue in the cable tie's racheting mechanism to jam it.
With luck will then able to slide the cable tie over the handles as and locking or release wanted.
My uncle Kenny once used a blow torch to solder a live gas pipe....may he RIP
He and my dad would have been great friends
On the 22mm perhaps the use of the grips is acting as a heat sync?
Great invention , no risk of fire in wooden structures...
Where are you located
What so that fitting that comes with solder inside?
I have seen it done with hot air heat gun and semi circular deflector plate aroun the back of the pipe so you don't even need a heat mat but you slow down the process
How long do you heat up the fitting with a torch before soldering for comparison?
Perhaps a good idea to leave them resting over a mat if you're worried about the stand.
Depends on how hot you have your torch. me personally, I set my torch to but pretty low, just below being able to hear the hiss of the torch burning and for that level a 15mm or 1/2 pipe takes about 10 seconds to heat up.
try out the -
Rothenberger 3.6700 / 3.6701 Rotherm 2000 Electric Soft Soldering Unit 110 / 240 Volts
Fast safe flame free soldering for copper tube and capillary fittings.
2000 watt.
For use from 6 to 54mm diameter in any location.
Supplied complete with soldering tongs with a 4 metre cable, soldering tongs and 2 metres of mains cable.
instead of 120 watts
DIYer here. Thanks for the review, but I wouldn't have one. It in its current state it looks to me like version 0.1. The clamp parts need to fit more closely to the pipe OR the fitting and there should be some sort of clamp lock. The wattage should probably be higher as on 22mm it didn't have the guts required for good solder flow. 28mm - forget it.
Now, I reckon "version 1.0" would be good for the pro, as I was told by a plumber the other day that on a building site he would have to stay for a couple of hours after the last blowtorch enabled joint.
Superfire II all the way for me...
Probably not version 0.1 - I had a 25-30 year old set of these (Antex, but yellow) which I finally took to the skip a few weeks ago, unused.
They've been around for YEARS I used one when I re-plumbed my house over 20 years ago but only for some joints in tricky locations, I used gas for the rest.
10:13 the pipe moves in the tee as you take off the element. Would that not cause a problem?
22mm tee joint, I suggest to start heating at first bottom joint as heat rises slowly, move heater up the joint and solder as you go, heating above tee first probably not effective as good percentage of heat travelling up the pipe.
The gripwrench used to hold on the 22mm pipe, was acting like a heatsink.
Would be better if it had some kind of ratchet build in, so it actually clamped, without requiring constant grip pressure on them.
Without any kind of heat protection on the outer edges, and I can see many injuries, as you mention in the video, bumping into them, or potentially knocking them over.
I definitely needed this last week. I cut the hutch on the floor to do some soldering n lots of spider webs 🕸 as soon as the torch lit the webs start to burn away. I was shitting myself. I thought the whole house would burn down. 😟
Perfect for Branding Emily
Will wait for V2
Does it work on AC linesets?
Thanks for the video. But I think that the reason that the 28mm one hasn't worked well is because your grippers are working as a heat sink and effectively you are heating up the grips and this is debiting heat from the iron jaws.
Maybe heat the pipe near the fitting then apply your solder?, This would ensure a perfect wrap around and heat distribution, And put the element on the centre of the capillary fitting to do both sides in one stroke, Just a thought..
I think these have a place in the tool box but to be honest I don't like using them. The weight of them tends to mean movement on the joints particularly vertical ones, the are safer than flames but just awkward.
Agree!
careful putting grips on the soldering element, the pipe should be grounded and there should be insulation but if there are problems the tool handle rubber on a knipex normal tool is not rated for any voltage.. so I would advise that anyone that wants extra grip use a pair of electrically safe insulated pliers (1000V rated grips).
2:25 oh my god. I've soon those dime in dozen holders as mosquito repellent holder. That has to be the "made cheap" record of all time to have those for such device 😲
The biggest problem with it is that as soon as you plug into the customers socket, they will moan about you using their electric 🤣
How much does this item cost ?Is it something that anyone can find useful or is it for the professional only ?
Putting pliers on the heating elements of the unit will absorb the heat back into the pliers pulling it away from your tubing you want to solder.
James, you've got the emissivity set incorrectly on your thermal camera if you want to look at the temperature of metal objects!
Where it might be useful, sweating out a leaking fitting in a finished area ?
Just a matter of time until there is a no open flame policy on building sites and your insurance tells you that if you use gas flame then you pay a lot more.
The grips do need to have a timer so they don't get left on by accident and jaws that self grip
You know what I can see those being really good at sweating off joints. Clamp the fitting and wiggle it off whilst keeping the heat on.
Never heard a solder joint referred to as being "sublime"!
It would be nice if the jaws were spring loaded so you could just clamp it on and let go while it heats the fitting.
Bought these so didnt set fire to close flamable stuff even with heat mat for scorching. The promo I saw a while back shows heating pipe to side of joint.
Dont think they are a speed item like you say more get you out of trouble spot.
Oh and the pliers are heat sink 🤣.
It would be great for gas pipes
What about in commercial places where you need a hot works permit for the blowtorch? Instead of the faff with paperwork and risk assessments would these be good there? 🤔
Try getting a hot works permit on a nhs site, its like asking for a pay rise
The NHS gravy train keeps on choo’ing
Got one bout 5 years ago used half a dozen times does get you out of hard to reach places
A good idea but it needs more thought in the implementation
In sure other people mentioned this but clamping it with pliers is gonna make it take longer to heat up and even possibly make it too cool. Maybe try it again with out them jic?
Pinned comment!
Nice concept. Obviously this is marketed towards non-professionals (i.e. home owners) as I can't see professional tradesmen using it since time is money and some job sites may not have power outlets within reach; even using extension cords.
From a homeowner point of view, the price of one of these buys a fair pile of pushfit or compression fittings.
I'm struggling to figure out the niche for this, maybe installation of gas piping in inaccessible high fire-risk areas (IIRC in the UK compression joints aren't allowed on inaccessible gas pipes).
Tin the tool first mate to help with heat transfer!
Surely if you are putting a clamp onto it the great will disperse and not be as hot. Makes sense to me.
If you know anything about electronics and/or DIY, you would be able to make yourself a high power version of these :)
Or don't be daft and get yourself a normal 500W-1000W handheld heating tool, like induction ones or the electric soldering guns, the ones where you pull a trigger and get hot fast.