Great job, super clean nice looking build ! Don't worry about some of these other negative comments. Not all ports have to be 6" X 12" slots or 6" round. The only reason for using a large port is usually to increase efficiency and reduce any port noise. A lower powered system as you built does not have that worry. I bet in the van it sounds pretty good. Again well done.
Could have 'recessed' the amp a bit more to make it more durable and less subject to 'knocking' because you have the 'cut out' anyway. Nice clean finish simple look. Love it.
Thanks for the feedback. Yes the amp is a bit underpowered for the sub but the total output is more than enough I need in my prefered level of music listening in and out of my mini van. 😊
@@chrclmnky sayang naman sir sana nandito ka bulacan/pampanga area. sa amin lang sa malolos mga 10km na drive makakadaan ka ng mahigit 10 na car audio shop. ganun kahilig mga tao dito
@@chrclmnky sir, question po pala. naka 6.5" subwoofer ako LL 250w RMS. anong FPL ko sya iset? kasi parang nabasa ko pag maliit sub dapat taasan ang freq. tama po ba? salamat sir
that's pretty interesting. I noticed that you have a lot of DIY stuff going on here and wanted to know if you've ever tried the ozone generator method of getting rid of bad smells in a car.
it's supposed to be plug and play, like put a boxy thing in your car and wait, but I've never really done anything like it so I wanted to ask since it's supposed to be some sort of like "insider guru" level stuff that's super simple. I figured with your awesome DIY knowledge you might have heard of it. Thanks for the reply man :)
WHen you are installing power cables from battery (in most cases just +, and gnd is taken from the trunk) alwayz use one side of your car for power cables from bat, and other side for signal RCA cables from headunit. Just because you can get buzzing alternator noise from your loudspeaker. If you once get buzzing alternator noises you have to check your ground and make it better, if you still got this problem you can buy rca ground loop fix condenzators. Or cheapest solution is with a simple wire ground your rca conectors on the hadunit to headunit cover, this work :) Worked for me too, even im used different sides, ive got a BOOM sound when I turned off my engine.. Using a high quality rca cables could solve this , but its not recommended to install these cables together. Btw nice clean work , looks great, and nice MDF high quality materials are you workin with . Keep up the good work . For my builds , visit channel wutdafuqq22 on youtube. Sorry for my eng , homies.
Not even 150 thats max 80Watts with no controll or dampaning of the woofer and cause the box is small and not even calculated right it won´t be loud a all
depends on the sub. if it needs 100 watts RMS then you should never give it less. otherwise you'll starve it. and like the name implies, same as in humans, if you don't have a proper power intake, you'll stop working sooner. so if you underpower a sub it will die sooner.
1000w speaker means that the speaker will strike at 999w or it will blow at 1001? At which frequency it will accept the 1000w? For how long? At which THD (%)? At which temperature and/or humidity? I have the impression that a speaker/amp complex is an active system with constanlty changing parameters where "static" specs like "1000w" simply does not aply.
A quick question bro mounting the amplifier on the subwoofer box won’t create any complications by the jar & vibrations of subwoofer to the amplifier? Please respond...anyway impressed by your project bro..
Very good question. I enclosed the amplifier board with a scrap plywood and MDF, glued heavily to ensure air tight. Can be seen on 5:05 spot. Subwoofer air pressure, jarring and vibrations can damage the small electronic components on the amp board. :) Thank you for watching.
CHRCLMNKY Thank you for your prompt reply..I was with a big ? Mark for the past 1 month where to keep my pioneer amp in the car...well you solved it...it’s a bit heavy but I think I can fix it with bolts outside the subwoofer box...Many thanks
600 watt amp and 1k sub. may not be the best match. I enjoyed the build, clean lines with a jig saw!. Looks great, clean install. I just hope no one hops in the car and cranks it up till it pushed distortion through that sub and frys it...(ask me how i know about that) but great vid none the less!!!
@@chrclmnky I built an enclosure for an 8" JBL Stage 82 tuned at 50Hz using a larger enclosure than the one suggested by JBL in the manual. After testing it, as you do so, with Dats, it turned out to be turned at 46Htz.
Very good build bro, you're the only person I've seen to use (T-nuts) to install the sub woofer onto the baffle, I believe that is the only and secure way to mount a sub woofer, wish you had a better camera mic to capture the true bass response, what is the box frequency tuned to?
Thank you, James. If I can remember properly, the box was tuned to 32Hz? Actually the amp is so under powered for the sub but good enough for everyday music listening while driving around town.
Thanks, I appreciate your quick response, I am considering installing a small sub underneath my rear passenger seat, and I like your build, like you, I just want a casual bass boost, nothing to shake any panels or fixtures loose, just something to complement the Rockfords I installed.. Hit me up if you make anymore upgrades to your system, Thanks in advance!!!!
I apologize, Should have asked for a track list, Your bass test songs I have, I test them out on my DJ system often and drive my neighbors crazy, (LOL), I am watching your video again just to get a general idea of how to build my sub box, but I believe I am gonna use a Rockford Fosgate amp, I am not familiar with the amp you used. Once again, Awesome tutorial video bro!!!!!!!!! :-)
@@chrclmnky actuly im 52 yrs old indian now working in oman. Bro i hv 1 hertz amp but on that amplifire no bridge connection for subwoofer . Here u hv any idea that i can use subwoofer ????
@@chrclmnky sir baka naman maka hingi ng design ng box para sa pang sub woofer yun pong simple lang po at hindi kumakain ng space yun pong pang 15"to 18" na sub speaker.. ang amp ko po ay ace MA 4002N...400W
Thanks Luther. That is a 3.5" diameter plastic port tube. Bought from a local electro-audio shop. I just extended it with a plumbing PVC pipe and connectors.
Hi! I have a question i was planing to buy the exact amp that you bought But the subwoofer im going to use is a targa subwoofer it only has a peak power of 250watts so is the amplifier gonna toast the speaker at max volume or the speaker will handle max volume fine?
Snoopy GaminG you can just say 30cm... you don't have to measure in mm... also, it doesn't matter what you think the port size should be, as long as it is properly tuned it doesn't matter.
No it does matter because if its to small you get portnoise and the effect of the port gets less and less the port cross sectional area shoud be at least 1/3 of the cone area of the speaker which would be 3,5 Inches in this case or 17cm
Cupid Stunt yea I also use pvc tubes as ports mostly just cause it’s simple if ein want do build something strong and properly I use the enclosure as port
What's the problem? Interference? That is a thing of the past. It's already 2018 and we now have nicer things called "shielded RCA cables". Try it, they're nice.
Hello Shiv. Do you mean the SEALED (no port hole) subwoofer box? Yes sealed box are best for vehicles buy you need to use a higher power amp because sealed box needs more power.
My sealed subwoofer producing a sound like when we vibrate cars no. Plate. If i make a air port in subwoofer box it will stop making that sound?? it is actually in high volume not in low. Plss bro tell me 😀😀
Hello how you doin. Amp just ok but a little underpowered for the subwoofer. But total output is more than enough to my listening needs, in or out the vehicle. There are available larger amp power and also larger in size. Check out at Aliexpress, search for "12v subwoofer amplifier board".
@@kimchifan1 This is a 1000w RMS Class D amp I purchased a year ago- czcams.com/video/DXXAAVbYStg/video.html Currently editing a video of a 1500w RMS variant and will upload very soon.
Thanks you, but there is a problem here, as i am new here and some time unable to understand the definition, i have 12" sony subwoofer xs-gtr121l, and i want to make box, and i dont under stand what size of box will best for this sub to get the best result. if you can help me, please advise
Stay tune and subscribe to my channel, I'm about to build a similar subwoofer as you have now, Sony NW1200 Xplod. It will be perfect for a 0.88-1.0 cubic feet of sealed box enclosure. You'll have to use a subwoofer calculator to get the actual measurements by the given volume.
Great job, super clean nice looking build ! Don't worry about some of these other negative comments. Not all ports have to be 6" X 12" slots or 6" round. The only reason for using a large port is usually to increase efficiency and reduce any port noise. A lower powered system as you built does not have that worry. I bet in the van it sounds pretty good. Again well done.
Yessir! Audio system not for showing off but entirely for music listening. ☺ Thanks for the feedback.
Τhe first reasonable comment I read about this built!
Plug the port with a rag or something to test it sealed, it might sound better. Usually those lower powered subs like sealed boxes.
Could have 'recessed' the amp a bit more to make it more durable and less subject to 'knocking' because you have the 'cut out' anyway. Nice clean finish simple look. Love it.
Thanks. 🥳
Excellent build! Great job! Your craftmanship alone is a great teacher!
Thank you ☺️
Nice build.. Oh, I love the music while hooking up box in yo ride..
Thanks. I agree. 😎
Nice and clean build
Thanks for the feedback. Yes the amp is a bit underpowered for the sub but the total output is more than enough I need in my prefered level of music listening in and out of my mini van. 😊
Yeah i figured out that sub is only 250w rms so i edited that out, but it should be enough for daily listening :)
Finally stumbled upon this, I have the same sub amp and was wondering what it sounds like.. Thanks for uploading the vid! PA-60A PMPO 600W
Hello, the amp sounds good, can deliver the right power for the subwoofer. Built-in active crossover is very accurate.
Can I Use this for home ??? as a subwoofer and maybe add a set of stereo speakers to get a 2.1 system?????
Yes you can but it will not sound as loud like in a car
Why
napaka swerte ng mga taga butuan sir!!! idol! sana nandito ka po sa bulacal or manila sayang
Ha! 🤣 Wala pong hilig mga taga dito sa car audio sir. May mga kakilala ako mga 5 lang. 😂
@@chrclmnky sayang naman sir sana nandito ka bulacan/pampanga area. sa amin lang sa malolos mga 10km na drive makakadaan ka ng mahigit 10 na car audio shop. ganun kahilig mga tao dito
@@chrclmnky sir, question po pala. naka 6.5" subwoofer ako LL 250w RMS. anong FPL ko sya iset? kasi parang nabasa ko pag maliit sub dapat taasan ang freq. tama po ba? salamat sir
@@gilberttan7244 LPF? Set lang nasa 63Hz. Masakit sa tenga if mas taas pa nyan.
@@chrclmnky ngayon po nasa 80hz sya low pass filter. babaan ko pa po? 6.5 inches po ito
Now I know who to look up on when I need ideas
That is very humbling. Thanks.
Finally I saw your face brother. You inspires me to do it myself.
that's pretty interesting. I noticed that you have a lot of DIY stuff going on here and wanted to know if you've ever tried the ozone generator method of getting rid of bad smells in a car.
My apologies never heard of about that. Sounds very sciencey.
it's supposed to be plug and play, like put a boxy thing in your car and wait, but I've never really done anything like it so I wanted to ask since it's supposed to be some sort of like "insider guru" level stuff that's super simple. I figured with your awesome DIY knowledge you might have heard of it. Thanks for the reply man :)
nice i love how the cable management looks :D
😃
CHRCLMNKY hi can i ask the title of the background music you used at 5:46 tnx😄
Track title: Huma-Huma - Not Too Cray
tnx so much :D
WHen you are installing power cables from battery (in most cases just +, and gnd is taken from the trunk) alwayz use one side of your car for power cables from bat, and other side for signal RCA cables from headunit. Just because you can get buzzing alternator noise from your loudspeaker. If you once get buzzing alternator noises you have to check your ground and make it better, if you still got this problem you can buy rca ground loop fix condenzators. Or cheapest solution is with a simple wire ground your rca conectors on the hadunit to headunit cover, this work :) Worked for me too, even im used different sides, ive got a BOOM sound when I turned off my engine.. Using a high quality rca cables could solve this , but its not recommended to install these cables together. Btw nice clean work , looks great, and nice MDF high quality materials are you workin with . Keep up the good work . For my builds , visit channel wutdafuqq22 on youtube. Sorry for my eng , homies.
wow its really awesome .
😆
Hey man great job! Looks really good. Looks better than pretty much any pre built box and I'm sure sounds really good too.
Can a PA 80D 1000 w same as that amplifier can drive a 1500 watts 15 inc. subwoofer?
600w PMPO is bullcrap specs. That amp is probably 150w to 200w at best however It will work.
😄😂
150w rms is good enough. Unless u have a very low sensitivity woofer, thats a different story.
Not even 150 thats max 80Watts with no controll or dampaning of the woofer and cause the box is small and not even calculated right it won´t be loud a all
1kw peak.. 250 Watts rms
I would give it 200rms
Plexeezda YT if you mean the Woofer you are right
That dog be like "oh new house for me"....
how did you create the subwoofer in the app.Please do a tutorial on that.Asking for the 2nd time.
Hello Nihal, there are ready made subwoofer models on the internet to download and export into TinkerCad.
Love it, builder after my own heart. I can smell the MDF dust!
Be sure to wear mask when sawing or routing. Don't end up like me who inhaled massive amount of dust and now complaining why my lungs hurt.
It’s awesome dude love it at the first video we had no internet and my account was lost so you remember me don’t you
^_^
This is amazing.... I want to make subwoofer like this.....
Yes sir you can. Enjoy building car subwoofers. 😄
I loved your work and always your first support
Thanks brother
Nice build kabayan! Makes me wanna build my own powered subwoofer
Thank you Sir. ☺ I'll build another powered subwoofer soon. Sealed type.
Looking forward for that build sir. I will also build a sealed powered sub using a shallow woofer ala pioneer
Nice build but that amp is not powerful enough to drive that sub.
How much power does the amp provide and how much power does the sub demand? I thought a speaker would work with any amount of power.
It will "work" but its like connecting that sub to an headphones output, its nonsense to use an such small amp with that sub.
Is there a rule about the power demand or does it rely on the technical specs of each sub?
depends on the sub. if it needs 100 watts RMS then you should never give it less. otherwise you'll starve it. and like the name implies, same as in humans, if you don't have a proper power intake, you'll stop working sooner. so if you underpower a sub it will die sooner.
1000w speaker means that the speaker will strike at 999w or it will blow at 1001? At which frequency it will accept the 1000w? For how long? At which THD (%)? At which temperature and/or humidity? I have the impression that a speaker/amp complex is an active system with constanlty changing parameters where "static" specs like "1000w" simply does not aply.
Hehe, power cable and signal cable in a single harness.
A quick question bro mounting the amplifier on the subwoofer box won’t create any complications by the jar & vibrations of subwoofer to the amplifier? Please respond...anyway impressed by your project bro..
Very good question. I enclosed the amplifier board with a scrap plywood and MDF, glued heavily to ensure air tight. Can be seen on 5:05 spot. Subwoofer air pressure, jarring and vibrations can damage the small electronic components on the amp board. :)
Thank you for watching.
CHRCLMNKY Thank you for your prompt reply..I was with a big ? Mark for the past 1 month where to keep my pioneer amp in the car...well you solved it...it’s a bit heavy but I think I can fix it with bolts outside the subwoofer box...Many thanks
Yes, traditional car amps can be bolted or screwed on the side or on top of the box no problem.
CHRCLMNKY Thanks a heap bro God Bless
Good work 😍
My favorite sobwoofer jpl🔈🔉🔊
Yee sir
Magaling po...maganda din po ang tunog kung may foam sa loob nkadikit sa wood...
Yes sir. :)
Dude! Your skills and videos are sooo awesome! Much respect!
Thank you M Awesome, you too are literally awesome! 😎
Awesome clean build dude big like!!
tenx 😉😆😂
600 watt amp and 1k sub. may not be the best match. I enjoyed the build, clean lines with a jig saw!. Looks great, clean install. I just hope no one hops in the car and cranks it up till it pushed distortion through that sub and frys it...(ask me how i know about that) but great vid none the less!!!
neither the amp has 600Watts nor the sub 1000Watts
i got inspired by you and bought the same amp and a Dats.
👍😎
@@chrclmnky I built an enclosure for an 8" JBL Stage 82 tuned at 50Hz using a larger enclosure than the one suggested by JBL in the manual. After testing it, as you do so, with Dats, it turned out to be turned at 46Htz.
A really good box. Inspiring. What's the the name of the first jam in the video?
Step 2 : Amplifier plate, pwede ba gamitin sa house yan at gamitin power supply is Switching power supply? Na mabibili din lazada? High 40amp?
Oo pwede. Mga at least 80A or 60A
Kinsa man Ang nag ukab Ani HAHAHAHA
YOWNNN proud bisaya here HAHAHAH 🧡
Excellent job. Great work. Appreciate the hard work.
Beautiful
Thanks Anup
Nice build
Thanks very much. 😁
Your work is so precise...!👌
Thank you Omkar for the nice feedback.
Never run your RCA's with your hot and ground wires you pick up engine noise through RCA cables awesome video dude speaker amp kit how much was it
Right but because of the Xcrossover in the sub you can not notice those noises
Very nice work, too clean
Yessir. Thank you. 😃😄
Very good build bro, you're the only person I've seen to use (T-nuts) to install the sub woofer onto the baffle, I believe that is the only and secure way to mount a sub woofer, wish you had a better camera mic to capture the true bass response, what is the box frequency tuned to?
Thank you, James. If I can remember properly, the box was tuned to 32Hz? Actually the amp is so under powered for the sub but good enough for everyday music listening while driving around town.
Thanks, I appreciate your quick response, I am considering installing a small sub underneath my rear passenger seat, and I like your build, like you, I just want a casual bass boost, nothing to shake any panels or fixtures loose, just something to complement the Rockfords I installed.. Hit me up if you make anymore upgrades to your system, Thanks in advance!!!!
CHRCLMNKY, What's the name of the second song played in your video?
@@MrJamesgrate Gunnar Olsen - Howling
I apologize, Should have asked for a track list, Your bass test songs I have, I test them out on my DJ system often and drive my neighbors crazy, (LOL), I am watching your video again just to get a general idea of how to build my sub box, but I believe I am gonna use a Rockford Fosgate amp, I am not familiar with the amp you used. Once again, Awesome tutorial video bro!!!!!!!!! :-)
Dili mn kaya ang box sir ga haming na. Gwapo n kung less volume lng para smooth
Super bro. From india big salute
Many thanks.
@@chrclmnky actuly im 52 yrs old indian now working in oman. Bro i hv 1 hertz amp but on that amplifire no bridge connection for subwoofer . Here u hv any idea that i can use subwoofer ????
Very Good bass and subwoofer
Thank you, Rasmus
If the van rockin, don't come knockin.
Holy shit the Build its so clean and nice
😻😎😉
Nice skills 👍
😍
I love the American screwdriver! !!
I got that screwdriver from a very cheap local Chinese flea market where everything's made in China for a dollar or two 😆.
Maganda ay simple yang gawa mo sir..saan kayo na order ng jbl speaker at amp
Lazada po.
@@chrclmnky sir baka naman maka hingi ng design ng box para sa pang sub woofer yun pong simple lang po at hindi kumakain ng space yun pong pang 15"to 18" na sub speaker.. ang amp ko po ay ace MA 4002N...400W
Hola! Disculpa no hay problema al no tener ventilación el amplificador, no se sobrecalienta demasiado
Pregunta?
Gracias me gusta tu trabajo.
Hello Maudilio, the amp has its heatsink facing outwards. As you can see the big aluminum fins, those are the heatsink.
i have the same subs. They do pretty good. Nice build btw 2 thumbs up!
Yessir 🙋
awesome video gunna make one myself
Yes sir, very easy and fun to build car subwoofers.
...very good... thank you form thailand 11 november 2022
thanks
I am from Germany and would like to build something like u. But this amp looks a bit strange...
Hello. Yes this amp is not powerful enough. The separate Class D mono amps are very good for subeoofers.
@@chrclmnky thx 4 answer, I really like to watch ur vids. Very interessting what u build
Good job like this setup
Thank you 🧐🤭🤭🤡
Nice box boss. Where did you acquire the black plastic used as a port hole?
Thanks Luther. That is a 3.5" diameter plastic port tube. Bought from a local electro-audio shop. I just extended it with a plumbing PVC pipe and connectors.
Good Work...
Thank you so much 😀
wonderful and nice box
also nice dog :)
Cute puppy
Nice video
Bro you are very talented
No I am not Lorenzo, I'm just a frustrated DIYer. 😢 But thanks very much for watching. 😃
Hi! I have a question i was planing to buy the exact amp that you bought
But the subwoofer im going to use is a targa subwoofer it only has a peak power of 250watts so is the amplifier gonna toast the speaker at max volume or the speaker will handle max volume fine?
This amp is nothing. Get a separate and dedicated amplifier that has at least a thousand watt RMS to drive your 250w subwoofers.
@@chrclmnky maybe when i got a job 😂 I'm just saving up the money that my parents are giving to me 😊
@@anxiety1209 😆
Nice but in my opinion the reflex tube is too small for a 300mm speaker.
Too small reffering to the lenght or the cross section of the tube?
Ernestom5 ccvc
Snoopy GaminG you can just say 30cm... you don't have to measure in mm... also, it doesn't matter what you think the port size should be, as long as it is properly tuned it doesn't matter.
No it does matter because if its to small you get portnoise and the effect of the port gets less and less the port cross sectional area shoud be at least 1/3 of the cone area of the speaker which would be 3,5 Inches in this case or 17cm
Cupid Stunt yea I also use pvc tubes as ports mostly just cause it’s simple if ein want do build something strong and properly I use the enclosure as port
Well done mate..tweeter nlang ang kulang...
New subs here! Regards to all
Thanks for the comment. Tweeters are inclusive within the coaxial speakers installed in left and right doors. 6.5" coaxial speakers.
This makes me wanna to get my hcca 12.2 ready for stereo season but I fried my sound stream 2,5000
RCA signal cables right up against the power wire lmao.
The box looks nice tho
What's the problem? Interference? That is a thing of the past. It's already 2018 and we now have nicer things called "shielded RCA cables". Try it, they're nice.
CHRCLMNKY Dayum son, where'd ya find that roast?
@@sethh8892 ik was like dayyuuummm😂😂😂😂😂😂
Awesome work
Thanks a lot 😊
Nice puppy
Ryder Nigga ryder nigguh!
Hi bro can you tell me what dimensions have this project
Good working 💪 👏
Hello Selim, there is a link to the Tinkercad schematics in the video description. Thanks.
@@chrclmnky😂😂
Ka nice sa gawa mo ka idol harang pa
LMAO! so much unnecessary hate in the comments, I swear these kids are so jealous of your new box.
Superb... Very useful video...
Nice build sir . Ang linis.ssk ko lng wala po bang port noise?
Thanks for the feedback. No port noise. ☺
wah Bhai manna padega aapko
Sir can u give me some idea please
I bought 12 inch 1400w JBL subwoofer which amplifier will u prefer for it give me some options.
Hello Dash, get an amplifier that supports 1 Ohm load stable. With at least 1000w RMS.
@@chrclmnky thanku so much sir for sharing you precious time with us.❤️
@@Dash-Ø7-X anytime
Great work mate. Also nice music.
Thanks very much, Martin. 😎😁
Nice bass😁😁 But what if we do not make a air port in bass box . It produce same sound like yours??
Hello Shiv. Do you mean the SEALED (no port hole) subwoofer box? Yes sealed box are best for vehicles buy you need to use a higher power amp because sealed box needs more power.
Sealed subwoofer boxes sounds more accurate and sounds tighter than the ported box.
My sealed subwoofer producing a sound like when we vibrate cars no. Plate. If i make a air port in subwoofer box it will stop making that sound?? it is actually in high volume not in low. Plss bro tell me 😀😀
I have JBL 1200w subwoofer
Which is good for fixing it bass tube or bass box
karpenter ka all machines kahase buy karna padega uska link dijiye..
Nice ... The amplifier is it ok? I'm planning to get one just like that last year ... 50/50 sure.
Hello how you doin. Amp just ok but a little underpowered for the subwoofer. But total output is more than enough to my listening needs, in or out the vehicle. There are available larger amp power and also larger in size. Check out at Aliexpress, search for "12v subwoofer amplifier board".
600 W PMPO is about 30-50W rms for a jbl sub?
very nice
Can this be used as a home theater subwoofer?
Hello Naveen, yes you can use this for home theater if you have a 12V 30A power supply.
@@chrclmnky thank you so much I was thinking of building this for my dj set up. 😄
@@DJ_Naveen218 To be sure, get a 12V 60A or 80A.
@@chrclmnky just for the aesthetics can I put the puwer supply inside the box?
@@DJ_Naveen218 Yes, power supplies can be placed anywhere.
u r good karpenter
😉😆
Nice job !! Brother, what's the screws measures did you use ? Congrats from Brazil.
Screws are M6
Those amps don't come with the bass bosst function which expands the bass and creates sound pressure. I have it.
Yes sir correct. I still prefer those powerful separate amps.
Kamusta PA-80D ampli mo after 2 years of use? Nagkaroon ba ng issue? I'm planning to buy the same please help me decide based on your review. Thanks
It was sold right away after this build. Stay away from this kind of amps. Get yourself at least 100w RMS or more for car applications.
@@chrclmnky Any suggestion? Please share me the the link. Thanks.
@@kimchifan1 This is a 1000w RMS Class D amp I purchased a year ago- czcams.com/video/DXXAAVbYStg/video.html
Currently editing a video of a 1500w RMS variant and will upload very soon.
which ic or Transisgor is used in the amplifier?? and whats the fq range of the same.. if possible plz provide the link to the same amplifier
really good work!
Thanks! 😄😄😄
nice job pre !!!
matsalams sir 💰
The amplifier don't make 800w, probably not more than 150w
Yes you are correct.
@@chrclmnky aniway good project
Питание и тюлюпаны вместе, наводки не не слышал😃
Only bass lang po ba sya ?
Yes that's what subwoofers are for.
Wow superb
Nice
good job, can you please advice the size (dimensions) of the box, like Width, height, length, Depth at bottom and depth at top. Regards.
Hello Green Chilli, kindly go to the video description for the info. Thank you for watching! 😊
Thanks you, but there is a problem here, as i am new here and some time unable to understand the definition, i have 12" sony subwoofer xs-gtr121l, and i want to make box, and i dont under stand what size of box will best for this sub to get the best result. if you can help me, please advise
Stay tune and subscribe to my channel, I'm about to build a similar subwoofer as you have now, Sony NW1200 Xplod. It will be perfect for a 0.88-1.0 cubic feet of sealed box enclosure. You'll have to use a subwoofer calculator to get the actual measurements by the given volume.
For cutting the speaker hole, what bit did you use and what is the name of the thing that made it a perfect circle?
Palm router
sounds good.. either is youtube compression.. its vibrating like hell..
Tenx
Amazing good work man...,
Thank you, Babar.