I just installed one of these (I haven't test ridden it yet, I'm replacing my exhaust at the same time and am waiting on it). A couple of comments based on my install: 1) The cylinder comes with piston very retracted. Even with pre-bleeding, it takes a LOT more fluid to move the piston to contact the clutch shaft. I actually removed the slave and pre-bled it again because I wasn't getting the pressure on the leaver. Once I realized how far back the piston was compared to the factory piston, I knew it would just take a lot more fluid. A vacuum bleeder won't push out the piston, so you have to pump the leaver. 2) The pickup on the master reservoir is pretty high up so it's easy to run the reservoir dry, which means you have to start all over again. 3) The tube you sent with mine was annoyingly small and it was pretty hard to get it on the bleeder. I couldn't do it by hand (as in the video), I had to use pliers to push it on and the tube tore in my first attempt.
What would it mean if after installation the pull is reduced significantly but then after some time requires more effort, almost back to the level required to pull in the clutch with the stock slave cylinder?
Hello rphd07, thank you for reaching out. Can you please contact us at 208-426-0659 MON-FRI 8-5PM MTN or shoot our team an email at customerservice@rekluse.com. We will get you taken care of.
Your written tool list has one hex driver, the photo shows two different size hex drivers. Additionally the hose clamps on the heat shields must be loosened, maybe add a 5/16 socket for a 1/4 inch drive for that. Much easier than a flat blade screw driver... Plan on installing one of these soon so I checked it in detail..
Hi Rich, thank you for your feedback. We're glad to hear your are interested in the product- please let us know if you have any questions or if we can assist.
Hello and thank you for your question. Yes, this will reduce clutch lever pull. We designed the slave cylinder to reduce the clutch lever pull by the maximum amount without compromising clutch control, modulation and shifting performance. We have installed the product with aftermarket levers. The only problem we run into is the bleeding process during installation. In those instances, we’ve been able to bleed the clutch slave cylinder using the stock lever and then putting the aftermarket lever back on after the bleeding process is complete. You may experience slight clutch drag with the combination of the aftermarket lever and the Rekluse slave cylinder installed, making it difficult to find neutral sometimes.
I have Softbrake's reduced levers on my 2019 Road King Special and today, I installed this Rekluse product. I did not have any issues bleeding the system and the clutch is awesome now! I can literally shift with my pinkie finger and hold the lever in with no tension. I highly recommend this product!!
Hey Anthony, thank you for reaching out! Our slave cylinder will move the clutch modulation point closer to the handlebars, as well as widen the friction zone. This will decrease the "on/off" feel of the clutch feed, giving you more control for smoother takeoffs.
Yes, it will expand the friction zone, providing improved control at the lever and resulting in better take offs. For full product details, please visit this link:rekluse.com/product/slave-cylinder-assembly-hd/
Hello Steven, thank you for watching our video and showing interest in our products. We have found that using our Rekluse Slave Cylinder can reduce your lever pull up to 30% for M8 models and 20% for Twin-Cam models. If you need further assistance, please contact us directly at 208-426-0659 or customerservice@rekluse.com. We are in the office Mon-Fri 8am-5pm MTN time. Thank you.
I just installed one of these (I haven't test ridden it yet, I'm replacing my exhaust at the same time and am waiting on it). A couple of comments based on my install: 1) The cylinder comes with piston very retracted. Even with pre-bleeding, it takes a LOT more fluid to move the piston to contact the clutch shaft. I actually removed the slave and pre-bled it again because I wasn't getting the pressure on the leaver. Once I realized how far back the piston was compared to the factory piston, I knew it would just take a lot more fluid. A vacuum bleeder won't push out the piston, so you have to pump the leaver. 2) The pickup on the master reservoir is pretty high up so it's easy to run the reservoir dry, which means you have to start all over again. 3) The tube you sent with mine was annoyingly small and it was pretty hard to get it on the bleeder. I couldn't do it by hand (as in the video), I had to use pliers to push it on and the tube tore in my first attempt.
I’m going to put on the automatic clutch system today and I also bought this slave thing... do I need both???
What would it mean if after installation the pull is reduced significantly but then after some time requires more effort, almost back to the level required to pull in the clutch with the stock slave cylinder?
Hello rphd07, thank you for reaching out. Can you please contact us at 208-426-0659 MON-FRI 8-5PM MTN or shoot our team an email at customerservice@rekluse.com. We will get you taken care of.
Your written tool list has one hex driver, the photo shows two different size hex drivers. Additionally the hose clamps on the heat shields must be loosened, maybe add a 5/16 socket for a 1/4 inch drive for that. Much easier than a flat blade screw driver... Plan on installing one of these soon so I checked it in detail..
Hi Rich, thank you for your feedback. We're glad to hear your are interested in the product- please let us know if you have any questions or if we can assist.
Does this reduce the clutch lever pull? Also can you use it with Softbrake's Reduced reach clutch lever?
Hello and thank you for your question. Yes, this will reduce clutch lever pull. We designed the slave cylinder to reduce the clutch lever pull by the maximum amount without compromising clutch control, modulation and shifting performance. We have installed the product with aftermarket levers. The only problem we run into is the bleeding process during installation. In those instances, we’ve been able to bleed the clutch slave cylinder using the stock lever and then putting the aftermarket lever back on after the bleeding process is complete. You may experience slight clutch drag with the combination of the aftermarket lever and the Rekluse slave cylinder installed, making it difficult to find neutral sometimes.
I have Softbrake's reduced levers on my 2019 Road King Special and today, I installed this Rekluse product. I did not have any issues bleeding the system and the clutch is awesome now! I can literally shift with my pinkie finger and hold the lever in with no tension. I highly recommend this product!!
@@harleydave2316 will appreciate short Vid. I'm interested in installing both rekluse slave cylinder and soft break levers. thanks
Does the rekluse clutch slave cylinder help change the lever point to half way on the clutch let out?
Hey Anthony, thank you for reaching out! Our slave cylinder will move the clutch modulation point closer to the handlebars, as well as widen the friction zone. This will decrease the "on/off" feel of the clutch feed, giving you more control for smoother takeoffs.
Will this increase the friction zone?
Yes, it will expand the friction zone, providing improved control at the lever and resulting in better take offs. For full product details, please visit this link:rekluse.com/product/slave-cylinder-assembly-hd/
Hi , any dealers ,suppliers ,in Ireland?
Do you have an unit that fits the Twin Cams?
Hi Bruce, the unit for the Twin Cam models is available for pre-order. To order, please give us a call at (208) 426-0659 8AM - 5PM MST.
CAN THIS BE USED WITH THE REKLUSE AUTO CLUTCH
Thanks for your question. Yes, the slave cylinder is compatible with the Rekluse RadiusX auto clutch.
Does it make it easier
Hello Steven, thank you for watching our video and showing interest in our products. We have found that using our Rekluse Slave Cylinder can reduce your lever pull up to 30% for M8 models and 20% for Twin-Cam models. If you need further assistance, please contact us directly at 208-426-0659 or customerservice@rekluse.com. We are in the office Mon-Fri 8am-5pm MTN time. Thank you.